Electroluxメーカー95604 Gの使用説明書/サービス説明書
ページ先へ移動 of 26
AUS ERFAHRUNG GUT 95600 G - 9560 1 G - 9560 2 G 95604 G Gas hob Table de cuisson Kochmulde Gaskookplaat Piano di cottura Operating and Installation Instructions GB Notice d’utilisation et d’encast.
2 Important Safety Information You MUST r ead these warnings car efully before installing or us ing the hob. If you need assi stance, contact our Customer Care Department on 087 05 350 350 Installation ● This hob must be installed by qualified personnel, accor ding to the manufacturer’ s instructions and to the relevant British Standar ds.
3 ● When in use a gas cooking hob will produce heat and moisture in the room in which it has been installed. Ensure there is a continuous air supply , keeping air vents in good condition or installing a cooker hood with a venting hose.
4 Content s Important Safety Information .................................................................... 2 In structions for the User .............................................................................. 6 Description of the Hob ........
5 This appliance is manufactured accor ding to the following EEC dir ectives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition.
6 1. Hob T op 2. Rapid Burner 3. Semi-r apid Burners 4. Auxiliary Burner 5. Contr ol knob for back right burner (semi-rapid) 6. Contr ol knob for back left burner (semi-rapid) 7.
7 HOB BURNERS To light a burner , turn the relevant contr ol knob anticlockwise to the maximum position, then push it down to ignite the burner . Upon, ignition, keep the knob pushed down about 5 seconds, then adjust the flame as required. If the burner does not ignite, turn the control knob to zer o, and try again.
8 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob fr om the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
9 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local AEG Service Force Centr e.
10 Service and Spar e Part s When you contact the Service Force Centr e, they will need the following information: 1. Y our name, address and post code. 2. Y our telephone number 3. Clear and concise details of the fault 4. The model and the serial number (see r ating label on the back of this instruction booklet) 5.
11 Guarantee Condition s AEG offer the following guar antee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the fir st retail purchaser , which must be verified by pur chase invoice or similar documentation.
12 OVERALL DIMENSIONS Width: 580 mm. Depth: 51 0 mm. Height: 88 mm. Weight: 8 Kg. CUT OUT DIMENSIONS Width: 550 mm. Depth: 470 mm. Thickness: 30 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply , 3 core flexible cable with non r ewireable plug fitted with a 3 amp cartridge fuse.
13 BURNER RAPID SEMI-RAPID AUXILIARY (large) (medium) (small) POSITION MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 2.9 0.65 1.9 0.45 1.0 0.33 NOMINAL FLOW RATE m 3 /h 0.276 0.062 0.181 0.043 0.095 0.031 NOZZLE REFERENCE 119 Adjust. 96 Adjust. 70 Adjust.
14 Important safety r equir ement s This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations ar e contained in the following British Standards Codes Of Pr actice: B.
15 650 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 600 mm 700 mm 400 mm 100 mm 400 mm 50 mm 55 mm 50 mm CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN .
16 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded elbow , adjustment is fixed so that the washer is fitted between the components as shown in the diagram.
17 550 470 580 510 55 min. FO 2359 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or dr awer If the hob is to be installed above a cupboar d or drawer it will be necessary to fit a heat resistant boar d below the base of the hob on the under side of the work surface.
18 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arr angements must be taken in designing the furnitur e unit, in or der to avoid any contact with the bottom of the hob which can be heated when it is operated.
19 Fitting the hob to the worktop Befor e fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to pr event spillage near the hob seeping into the cabinet below .
20 Electrical connection s Any electrical work requir ed to install this hob should be carried out by a qualified electrician or competent person, in accor dance with the current r egulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measur es not be observed.
21 P ermanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the requir ed load in compliance with the current electric r egulations.
22 Fault Finding Preliminary Electrical Sy stem s Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supply should now be satisfactory. Carry out: D: Resistance to Earth check.
23 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight.
24 Check gas supply at burner Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ig.
25 Commi ssioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the pr ocedure below . 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
26 Conver sion from Natur al Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injector s are fitted and the gas r ate is adjusted to suit.
デバイスElectrolux 95604 Gの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Electrolux 95604 Gをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはElectrolux 95604 Gの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Electrolux 95604 Gの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Electrolux 95604 Gで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Electrolux 95604 Gを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はElectrolux 95604 Gの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Electrolux 95604 Gに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちElectrolux 95604 Gデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
