ElitegroupメーカーA790GXM-AD3の使用説明書/サービス説明書
ページ先へ移動 of 72
.
.
Preface Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author .
ii Preface Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • This device may not cause harmful interference, and • T.
iii T T T T T ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS Preface i Chapter 1 1 Introducing the Motherboard 1 Introduction........................................................................................
iv Integrated Peripherals..................................................................32 Power Management Setup.............................................................33 PCI/PnP Setup..........................................................
1 Introducing the Motherboard Chapter 1 Introducing the Motherboard Introduction Curr ently , the memory maximum size we have tested is 8 GB (2 GB per dimm) .
2 Introducing the Motherboard Feature Processor HyperT ransport TM T echnology is a point-to-point link between two devices, it enables integrated circuits to exchange information at much higher speeds than currently available interconnect technologies.
3 Introducing the Motherboard Onboard LAN This motherboard supports Ultra DMA bus mastering with transfer rates of 133/100/66/33 MB/s. Expansion Options The motherboard comes with the following expansion options: • T wo PCI Express x16 slots for Graphics Interface • T wo PCI Express x1 slots • T wo 32-bit PCI v2.
4 Introducing the Motherboard Motherboard Components The above image is for reference only; please take the actual motherboard for detailed parts..
5 Introducing the Motherboard T able of Motherboard Components LABE L COM PONENT S 1. CP U Socket Socket for A M D Phenom TM II processor (s ocket A M 3) 2. CPU _F AN C PU cooling fan connector 3 . D I MM1 ~ 4 240-pin DD R3 S DR A M slots 4. AT X_ PO WER Standard 24- p in A T X p ower connector 5.
6 Introducing the Motherboard Memo.
7 Installing the Motherboard Chapter 2 Installing the Motherboard Safety Precautions • Follow these safety precautions when installing the motherboard • Wear a grounding strap attached to a ground.
8 Installing the Motherboard Do not over-tighten the screws as this can stress the motherboard..
9 Installing the Motherboard Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan, make sure that you DO NOT scratch the motherboard or any of the surface- mount resistors with the clip of the cooling fan.
10 Installing the Motherboard 1 Install your CPU. Pull up the lever away from the socket and lift up to 90-degree angle. 2 Locate the CPU cut edge (the corner with the pin hold noticeably missing). Align and insert the CPU correctly . 3 Press the lever down and apply thermal grease on top of the CPU.
11 Installing the Motherboard Installation Procedure Refer to the following to install the memory modules. 1 This motherboard supports unbuffered DDR3 SDRAM only . 2 Push the latches on each side of the DIMM slot down. 3 Align the memory module with the slot.
12 Installing the Motherboard T able A: DDR3 (memory module) QVL (Qualified V endor List) The following DDR3 1333/1066 / 800 memory modules have been tested and quali- fied for use with this motherboard.
13 Installing the Motherboard The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities.
14 Installing the Motherboard Follow these instructions to install an add-on card: 1 Remove a blanking plate from the system case corresponding to the slot you are going to use. 2 Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot.
15 Installing the Motherboard Connecting Optional Devices Refer to the following for information on connecting the motherboard’s optional devices: SA T A1~6: Serial A T A connectors These connectors are used to support the new Serial A T A devices for the highest data transfer rates (3.
16 Installing the Motherboard F_USB1~3: Front Panel USB headers The motherboard has six USB ports installed on the rear edge I/O port array . Addi- tionally , some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
17 Installing the Motherboard Installing a Hard Disk Drive/CD-ROM/SA T A Hard Drive This section describes how to install IDE devices such as a hard disk drive and a CD- ROM drive. About IDE Devices Y our motherboard has one IDE interface . An IDE ribbon cable supporting two IDE devices is bundled with the motherboard.
18 Installing the Motherboard Refer to the illustration below for proper installation: This motherboard supports the “Hot-Plug” function. 1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SA T A hard drive.
19 Installing the Motherboard Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. CLRCOMS_BTN Use the CLR_CMOS button to clear CMOS.
20 Installing the Motherboard Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: With A TX v2.x power supply , users please note that when installing 24-pin power cable, the latches of power cable and the A TX_POWER match perfectly .
21 Installing the Motherboard When installing 8-pin power cable, the latches of power cable and the A TX12V match per- fectly . 8-pin power cable Connecting 8-pin power cable PWR_F AN/SYS_F AN/NB_F AN.
22 Installing the Motherboard Front Panel Header The front panel header (P ANEL) provides a standard set of switch and LED headers commonly found on FULL A TX, A TX or Micro A TX cases.
23 Installing the Motherboard Power Switch Supporting the power on/off function requires connecting pins 6 and 8 to a momen- tary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off.
24 Installing the Motherboard Memo.
25 Using BIOS Chapter 3 Using BIOS About the Setup Utility The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play . The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.
26 Using BIOS Press the delete key to access the BIOS Setup Utility . CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. v02.
27 Using BIOS Standard CMOS Setup This option displays basic information about your system. Help Item CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Use [ENTER], [T AB] or [SHIFT -T AB] to select a field. Use [+] or [-] to configure system Date.
28 Using BIOS IDE BusMaster (Enabled) This item enables or disables the DMA under DOS mode. W e recommend you to leave this item at the default value. Press <Esc> to return to the main menu setting page.
29 Using BIOS Boot Up Numlock Status (ON) This item defines if the keyboard Num Lock key is active when your system is started. Quick Power on Self T est (Enabled) Enable this item to shorten the power on testing (POST) and have your system start up faster .
30 Using BIOS Hard Disk Drives (Press Enter) Scroll to this item and press <Enter> to view the following screen: Hard Disk Drives 1st Drive TOSHIBA TransMemory Help Item Specifies the boot sequence from the available devices. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
31 Using BIOS Advanced Chipset Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer . GFX Clock Override (Disabled) Use this item to enable or disable GFX Clock Override.
32 Using BIOS Integrated Peripherals This page sets up some parameters for peripheral devices connected to the system. Onboard IDE Controller (Enabled) Use this item to enable or disable the onboard IDE interface. SA T A Configuration (Native IDE) Use this item to show the Serial A T A Configuration options: Disabled, Compatible, Enhanced.
33 Using BIOS Power Management Setup This page sets up some parameters for system power management operation. Select the ACPI state used for System Suspend. Help Item CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Power Management Setup ACPI Suspend T ype (S3) Use this item to define how your system suspends.
34 Using BIOS Press <Esc> to return to the main menu setting page. Resume on RTC Alarm (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the system’s R TC (realtime clock).
35 Using BIOS PC Health Status On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.
36 Using BIOS System Component Characteristics These items display the monitoring of the overall inboard hardware health events, such as System & CPU temperature, CPU & DIMM voltage, CPU & system fan speed,.
37 Using BIOS M.I.B. (MB Intelligent Bios) This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have in- stalled in your system. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
38 Using BIOS Spread Spectrum (Disabled) If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system. Auto Detect DIMM/PCI Clk (Enabled) When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots.
39 Using BIOS Press <Esc> to return to the main menu setting page. V oltage Function (Disabled) Use this item to enable or disable the V oltage Function.
40 Using BIOS Save & Exit Setup Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility . When the Save and Exit dialog box appears, select [OK] to save and exit, or select [Cancel] to return to the main menu.
41 Using BIOS Updating the BIOS Y ou can download and install updated BIOS for this motherboard from the manufacturer’s W eb site. New BIOS provides support for new peripherals, improve- ments in performance, or fixes for known bugs.
42 Using BIOS Memo.
43 Using the Motherboard Software Chapter 4 Using the Motherboard Software The Auto-install CD-ROM makes it easy for you to install the drivers and software for your motherboard. If the Auto-install CD-ROM does not work on your system, you can still install drivers thr ough the file manager for your OS (for example, W in- dows Explorer).
44 Using the Motherboard Software Setup T ab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD.
45 Using the Motherboard Software 2. Click Next. The following screen appears: 3. Check the box next to the items you want to install. The default options are recom - mended. 4. Click Next run the Installation Wizard. An item installation screen appears: 5.
46 Using the Motherboard Software Follow these instructions to Disable V ista UAC function: 1. Go to Control Panel . Method 1. Run Reboot Setup Windows V ista will block startup programs by default when installing drivers after the system restart.
47 Using the Motherboard Software 2. Select Classic View . 3. Set User Account . 4. Select Turn User Account Control on or off and press Continue ..
48 Using the Motherboard Software Manual Installation Insert the CD in the CD-ROM drive and locate the P A TH.DOC file in the root directory . This file contains the information needed to locate the drivers for your motherboard. Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers.
49 Using the Motherboard Software HDMI Audio setting SOP OS: XP system 1. Control Panel-->Sound and Audio Device Properties 2 . b. Audio--> Sound playback--> Default device--> HDMI Aud i o Output a. Audio--> Sound playback--> Default device--> HD Aud i o Output 3 .
50 Using the Motherboard Software OS: Vista system Control Panel--> Soundback--> Sound--> Digital Output Device (HDMI) --> Set Default 1. Volume --> Playback 2.
51 Using the Motherboard Software 3. Speaker --> Set Default --> OK User Speaker Palyback function working 4. SPDIF-Out --> Set Default --> OK User SPDIF-Out Playback function working This concludes chapter 4.
52 Using the Motherboard Software Memo.
53 A TI CrossFireX TM T echnology & Hybrid Graphics ® T echnology Suppor t Chapter 5 A TI CrossFireX TM T echnology & Hybrid Graphics ® T echnology Suppor t This motherboard supports A TI CrossFireX TM T echnology that allows you to install multi-graphics processing units (GPU) graphics cards.
54 A TI CrossFireX TM T echnology & Hybrid Graphics ® T echnology Suppor t 4. Connect the external cable to the corresponding port on your monitor . 3. Connect the two CrossFireX TM Edition graphics cards installed on PCIE16X_1 and PCIE16X_2 slots with the CrossFire Bridge.
55 A TI CrossFireX TM T echnology & Hybrid Graphics ® T echnology Suppor t 7. Enable the CrossFireX TM function in Catalyst Control Center . V iew The Catalyst TM Control Center provides two views; one is Standard view for begin- ners, the other is Advance view for advanced users to access and configure the complete features of the software.
56 A TI CrossFireX TM T echnology & Hybrid Graphics ® T echnology Suppor t Hybrid Graphics ® T echnology The Hybrid Graphics ® technology provides significant display performance boost to AMD-b.
57 A TI CrossFireX TM T echnology & Hybrid Graphics ® T echnology Suppor t 3. Click with your right mouse button on My Computer , then click the option Manage and choose the Device Manager , finally , click the Display Adapters. The following screen appears.
58 A TI CrossFireX TM T echnology & Hybrid Graphics ® T echnology Suppor t Note: 4. Enter Catalyst Control Center, you can see the option of CrossFire TM , click it and select Enable CrossFire TM , then Hybrid Graphics ® starts.
59 AMD RAID Configuration Setting Up a bootable RAID Array This section explains how to configure a bootable AMD RAID array . Setting Up the BIOS Use the arrow keys to select Integrated Peripherals (see Figure 1.1), then press Enter . The Integrated Peripherals screen (or a screen similar to it) appears.
60 AMD RAID Configuration 5 Enter the RAID BIOS Setup by pressing Ctrl-F when prompted, and proceed to set up the AMD RAID BIOS as described in the next section.
61 AMD RAID Configuration Select [2], then select LD 1 in the following page. 3 The Define LD Menu screen appears (Figure 1.4). Figure 1.4 Define LD Menu Using the Define a New Array Screen If necessary , press the tab key to move from field to field until the appropriate field is highlighted.
62 AMD RAID Configuration Figure 1.5 illustrates the Define a New Array screen after two disks have been assigned as RAID 0 array disks. Figure 1.5 FastBuild Utility—Array Disks Assigned Assigning the Disks 1. Select the Assignment to Y to designate a free disk to be used as a RAID array disk.
63 AMD RAID Configuration Figure 1.7 Main Menu Press ESC to exit. 4 Press Y to reboot. 3. The Main Menu screen appears (Figure 1.7). Figure 1.8 The following screen appears (Figure 1.
64 AMD RAID Configuration 1 Copy all files in " ...RAIDA TISB750FloppyW in3264" to a floppy disk. After you complete the RAID BIOS setup, boot from the Windows CD. Figure 1.10 Windows Setup—Specify Devices Installing the RAID Drivers Y our system may come with a Windows install CD that already includes AMD RAID drivers.
65 AMD RAID Configuration b Select “A TI AHCI Compatible RAID Controller -x86 platform” and press Enter for 32-bit OS or Select “A TI AHCI Compatible RAID Controller-x64 platform” and press Enter for 64-bit OS. The following Windows Setup screen appears listing both drivers:.
66 AMD RAID Configuration Memo.
デバイスElitegroup A790GXM-AD3の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Elitegroup A790GXM-AD3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはElitegroup A790GXM-AD3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Elitegroup A790GXM-AD3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Elitegroup A790GXM-AD3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Elitegroup A790GXM-AD3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はElitegroup A790GXM-AD3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Elitegroup A790GXM-AD3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちElitegroup A790GXM-AD3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。