EmersonメーカーBP7251の使用説明書/サービス説明書
ページ先へ移動 of 16
READ AND SA VE THESE INSTRUCTIONS Raphael Model No. CF2600AB01 CF2600WB01 CF2600PW01 Raphael II Model No. CF2650BC01 CF2650WB01 CF2650PW01 RAPHAEL ™ / RAPHAEL II ™ Part No.
2 W ARNING ! WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference.
1. Open carton containing your ceiling fan. Remove the top half of the styrofoam packing. Remove parts and check to see that you have received the following: a. Fan motor and shade assembly b. One motor cover c. One ceiling cover d. Five blade flanges e.
If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.
5 SECTION A Assembly Instructions for Installing the CF2600 and CF2650 Ceiling Fan with the Emerson SR330 Remote Contr ol or the SW350 W all Control 1. Obtain the hanger ball/downrod assembly and remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 1A).
6 11. Fold the wires from the downrod into the slot in the motor coupling (Figure 5A). Then slide the downrod down the wires and seat the downrod in the motor coupling. 12. Align the clevis pin holes in the downrod with the holes in the motor coupling.
7 DOWNROD PIN HANGER BALL CEILING COVER Figure 9A 17. Screw in four 60-watt (maximum) candelabra base lamps in the housing sockets (Figure 10A). Grasp the sockets and pivot them until the lamp bulbs are even with the top of the housing as shown. This will provide the optimum lighting effect.
21. Position the receiver by passing the opening in the receiver over the hanger pipe (Figure 14A). 22. Connect the black wire from the wiring harness to the black (hot) supply wire (Figure 6A). Connect the white wire from the wiring harness to the white (neutral) supply wire.
31. Using the 5/64” hex wrench (supplied), loosen the setscrew in the collar on the light kit adapter assembly. Then pass the connectors and the wires from the motor shaft through the collar (Figure 18A). Screw the adapter assembly onto the motor shaft and then tighten the setscrew to secure the adapter assembly to the motor shaft.
8. Install the setscrew (supplied) in the motor coupling and tighten using the 5/32” setscrew wrench (supplied) (Figure 3B). 9. Screw two 1” threaded studs (provided) into the motor (Figure 4B). Leave approximately 7/8” of the stud extending above the motor.
10. Position the ceiling cover over the downrod. Be sure the cover is oriented correctly, with the large opening at the top (Figure 5B). 11. Reinstall the hanger ball on the downrod as follows. Route the motor leads through the hanger ball and slide the hanger ball over the downrod (Figure 5B).
15. Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 9B). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 8B).
21. Attach one blade assembly to the motor hub using two 10-32 x 5/8” oval head screws (supplied) (Figure 13B). Do not tighten completely at this time. Install remaining blade assemblies in the same way. Gently snug all flange screws to the motor hub, working around the hub in a clockwise sequence.
14 Installation of the Decorative Suppor t Rods Assembly NOTE: The following procedures are to be performed only if you have installed the 18” or longer downrod. 1. Loosen the setscrew in the collar of the rod support assembly using the 5/64” hex wrench (supplied) and slide the support assembly over the downrod (Figure 1).
15 Using Y our Ceiling Fan 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box. 2. Check the operation of the fan and lights by using the wall controls or the remote control. 3. If airflow is desired in the opposite direction, turn your fan off and wait for the blades to stop turning.
Printed in Taiwan 04/03 Part No. F40BP72510004 Form No BP7251-4 Repair Par ts Listing Raphael Part Numbers Raphael II Part Numbers Key Model No. Model No.
デバイスEmerson BP7251の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Emerson BP7251をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEmerson BP7251の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Emerson BP7251の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Emerson BP7251で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Emerson BP7251を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEmerson BP7251の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Emerson BP7251に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEmerson BP7251デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。