EmersonメーカーCF960BS 00の使用説明書/サービス説明書
ページ先へ移動 of 12
Part No. F40BP72680001 Form No. BP7268-1 READ AND SA VE THESE INSTRUCTIONS WINDJAMMER ™ ® Net Weight: 27.6 Lbs. Ceiling Fan Owner's Manual LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
2 W ARNING ! WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference.
1. Check to see that you have received the following parts: NOTE: If you are uncertain of part description, refer to exploded view illustration. a. Fan motor assembly b. One light fixture assembly c. Six fan blades d. Six blade flanges e. One ceiling cover f.
5. Make sure the grommet is properly installed in the coupling cover, then slide the coupling cover on the downrod until it rests on the motor housing. Place the ceiling cover over the downrod. Be sure that the ceiling cover and the coupling cover are both oriented correctly (Figure 4).
7. The fan comes with blue, black and white leads that are 80” long. Before installing the fan, measure up approximately 6 to 9-inches above the top of hanger the ball/downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from the end of leads.
3. Screw the two threaded studs (supplied) into the tapped holes in the hanger bracket (Figure 9). 4. Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover (Figure 10).
7 To avoid possible fire or shock, make sure that the electrical wires are not pinched between the light fixture assembly and the mounting plate. W ARNING ! 3. Partially install two 3/16-24 x 1/4” Phillips round head screws in two of the tapped holes in the coupling adapter (Figure 13).
8 Installation of Light Adapter Plate NOTE: In order to use the light adapter plate (supplied), the wiring harness included as part of the light fixture assembly must be removed and be reinstalled in the light adapter plate. This Section contains the procedures to accomplish this.
9 Using Y our Ceiling Fan 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box. 2. Check the operation of the fan by gently pulling on the speed control pull chain switch (Figure 23). The operating sequence is as follows: THREE-SPEED 1st Pull—HIGH 2nd Pull—Medium 3rd Pull—Low 4th Pull—OFF 3.
10 WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble shooting your fan. T r ouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers.
13 26 27 14 28 16 17 15 24 20 9 19 18 3 1 5 4 6 7 8 2 21 25 23 22 12 11 10 11 Before discarding packaging material, be certain all parts have been removed.
Part No. F40BP72680001 Printed in Taiwan 05/03 Form No. BP7268-1 Air Comfort Products DIVISION OF EMERSON COMPANY 8100 W. Florissant ¥ St. Louis, MO 63136 Repair Par ts Listing Model No.
デバイスEmerson CF960BS 00の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Emerson CF960BS 00をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEmerson CF960BS 00の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Emerson CF960BS 00の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Emerson CF960BS 00で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Emerson CF960BS 00を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEmerson CF960BS 00の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Emerson CF960BS 00に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEmerson CF960BS 00デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。