EmersonメーカーEWC0902の使用説明書/サービス説明書
ページ先へ移動 of 32
9-INCH COLOR TV/VCR EWC0902 O WNER’S MANU AL As an E NERGY S TAR Partner, our company has determined that this product meets the E NERGY S TAR guidelines for energy efficiency.
1.Read instructions- All the safety and operating instructions should be read before the appliance is operated. 2.Retain Instructions- The safety and operating instructions should be retained for future reference. 3.Heed W arnings -All warnings on the appliance and in the operating instructions should be adhered to.
- 3 - EN 9J27 13.Outdoor Antenna grounding- If an outside antenna or cable system is connected to the TV/VCR, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFP A No.
AV OID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE This equipment has been tested and found to com- ply with the limits for a Class B digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- 5 - EN 9J27 T ABLE OF CONTENTS A NOTE ABOUT RECYCLING This product’ s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
- 6 - EN 9J27 FEA TURES • I nfrared remote control • Bilingual on screen menu display selectab le in English or Spanish • Real time counter– This shows the elapsed recording or playback time in hours, minutes, and seconds. The “–” indication will appear when the tape is rewound further than the tape counter position “0:00:00”.
- 7 - EN 9J27 OPERA TING CONTROLS AND FUNCTIONS - TV/VCR FR ONT P ANEL - 5 PO WER button– Press to turn TV/VCR on and off. Press to activate timer recording. 6 ST OP button– Press to stop the tape motion. EJECT button– Press in the Stop mode to remove tape from TV/VCR.
- 8 - EN 9J27 - REAR VIEW - 26 ANT DC 13.2V AC 120V 27 28 10 REC button– Press for manual recording. O TR button– Activates One T ouch Recording. (only on the TV/VCR) 11 V OLUME X X / Y Y b uttons– Adjust the volume level. 12 CHANNEL K / L b uttons– Press to select the desired channels for viewing or recording.
- 9 - EN 9J27 ANTENNA/CABLE CONNECTIONS DIPOLE ANTENNA HOOK UP 1. Push the stem of the Dipole Antenna (accessory) into the hole for antenna at the back of TV/VCR. 2. Connect the flat twin-lead cable from the Dipole Antenna to the 300/75 ohm Matching Adapter (accessory .
- 10 - EN 9J27 INST ALLING THE BA TTERIES 1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow . 2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings.
- 11 - EN 9J27 SET UP FOR USE Y ou can program the tuner to scan all the channels you receive in your area. NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3).
- 12 - EN 9J27 NOTES: • Auto clock setting only needs to be set once. But it can be done again if the clock’ s time has become incorrect for some reason.
- 13 - EN 9J27 CHANNEL SET UP AGAIN Make sure ... • Press the POWER button to turn on the TV/VCR. 1 Select “CHANNEL SET UP” Press the MENU button on the remote control. Press the PLA Y/ K or ST OP/ L but- ton to point to “CHANNEL SET UP”. Then, press the F .
- 14 - EN 9J27 SELECTING THE LANGUAGE Make sure ... • Press the POWER button to turn on the TV/VCR. NOTE: This function effects only the language on the screen menu and not the audio source. 1 Select “LANGU A GE” Press the MENU button on the remote control.
- 15 - EN 9J27 TV OPERA TION WA TCHING A TV PROGRAM 1 T urn on the TV/VCR Press the POWER button to turn on the TV/VCR. 2 Select the channel number Press the CHANNEL K or L button to select your desired channel number or press the number buttons on the remote control.
- 16 - EN 9J27 PLA YBACK NORMAL PLA YBACK Make sure ... • TV/VCR power must be turned on. 1 Insert a prerecorded tape If the erase-protection tab has been removed, the TV/VCR will start playback automatically . 2 To begin playbac k Press the PLA Y button.
- 17 - EN 9J27 PICTURE SEARCH This feature is very useful in finding or skipping over a particular scene on a tape. In this mode, the sound will be muted. 1)Y ou may view a video tape at a high speed in either a forward or reverse direction by pressing the F .
- 18 - EN 9J27 RECORDING TWO DIFFERENT T APE SPEEDS Before recording, select the tape speed from : SP mode (Standard Play) or SLP mode (Super Long Play). The table below shows the maximum recording/play- back time using T60, T120 or T160 tapes in each mode.
- 19 - EN 9J27 Make sure ... • TV/VCR power must be turned on. • Insert a cassette tape with its erase prevention tab in place. (If necessary , rewind or fast forward the tape to the point at which you want to begin recording.) NOTE: This unit will ONL Y record and view the same channel.
- 20 - EN 9J27 3 Begin O TR Press the REC/OTR button on the TV/VCR as many times as needed. The recording length will be deter- mined by the number of times you press the REC/OTR button. Each additional push will increase the recording time by 30 minutes.
- 21 - EN 9J27 For every day recording : To r ecor d a TV pr ogram at the same time on the same channel every day . (Example: Monday thr ough Sunday) Press the STOP/ L (down) button until “EVR Y DA Y” appears. Then, press the F .FWD/ B but- ton. For weekly recording : To r ecor d a TV pr ogram at the same time on the same channel every week.
- 22 - EN 9J27 TO CANCEL AN AUTOMA TIC TIMER RECORDING • After setting a pr ogram; 1)Press the POWER button. 2)Repeat steps [1] ~ [2] on page 20 and select a program you want to cancel. 3)Press the T -PROG. CLEAR button. 4)Press the MENU button on the remote control to return to TV mode.
- 23 - EN 9J27 3 Set wake up time Press the PLA Y/ K or ST OP/ L but- ton until to point to “TIME”. Press the F .FWD/ B or REW/ s button until your desired wake up time appears. Each additional push will increase (or decrease) the time by 10 minutes.
- 24 - EN 9J27 CABINET CLEANING • W ipe the front panel and other exterior surfaces of the TV/VCR with a soft cloth immersed in luke- warm water and wrung dry . • Never use a solvent or alcohol. Do not spray insec- ticide liquid near the TV/VCR. Such chemicals may cause damage and discoloration to the exposed surfaces.
- 25 - EN 9J27 TROUBLESHOOTING GUIDE If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR, locate the PROBLEM in the left column below . Check the corresponding CORRECTIVE ACTION column to remedy the problem.
- 26 - EN 9J27 GENERAL SPECIFICA TIONS CR T : 9 inch in-line gun, 90˚ deflection tube T elevision system : NTSC-M V ideo Heads : Rotary two-head T ape width : 1/2 inch T ape speed SP : 33.
- 27 - ES 0M21 1 T oma de entrada de audio (A UDIO)– Conéctela a la toma de salida de audio de su equipo de audio, videocámara u otra videograbadora. 2 T oma de entrada de vídeo (VIDEO)– Conéctela a la toma de salida de vídeo de su videocámara u otra videograbadora.
- 28 - ES 0M21 11 Botones de volumen (V OLUME X X / Y Y )– Ajustan el nivel del volumen. 12 Botones de canales (CHANNEL K / L )– Púlselos para selec- cionar los canales deseados para ver o grabar . Se puede mostrar el menú principal en la pantalla del televisor pulsando repetidamente este botón del televisor/videograbadora.
- 29 - ES 0M21 CONEXION DE LA ANTENA BIPOLAR 1. Introduzca la varilla de la antena bipolar (accesorio) en el orifi- cio destinado para la antena, en la parte trasera de la TV/VCR. 2. Conecte el cable bifilar plano de la antena bipolar al adaptador de acoplo (accesorio) de 300/75 ohm.
- 30 - ES 0M21 1) Abra la tapa del compartimiento de las pilas del mando a distancia presionándola en el sentido de la flecha. 2) Inserte 2 pilas tamaño “AA” en el compartimiento de las pilas, en el sentido indicado por las marcas de polaridad (+/-).
- 31 - ES 0M21 1) Conecte el extremo más prqueño del cordón de CA al conector de CA de 120V en la parte posterior de la TV/VCR. Luego, enchufe el otro extremo enun tomacorriente normal de CA. NOT AS: • Dede desconectar de la TV/VCR el cordón para la batería del automóvil antes de usar la alimentación de CA.
LIMITED W ARRANTY FUNAI CORP . will repair this product, free of char ge in the USA in the event of defect in materials or workman- ship as follows: DURA TION: PA R TS: FUNAI CORP . will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase.
デバイスEmerson EWC0902の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Emerson EWC0902をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEmerson EWC0902の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Emerson EWC0902の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Emerson EWC0902で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Emerson EWC0902を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEmerson EWC0902の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Emerson EWC0902に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEmerson EWC0902デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。