EmersonメーカーKF180の使用説明書/サービス説明書
ページ先へ移動 of 16
Net Weight: 30.9 Lbs. Part No. F40BP72840003 Form No. BP7284-3 U.L. Model No.: KF180 READ AND SA VE THESE INSTRUCTIONS KF180AP01 Antique P ewter with Natural Cher r y/Mahogany Blades KF180OZ01 Olde Br.
W ARNING: T o avoid fire, shock, and serious personal injury , follow these instructions. Safety Instructions 1. Read your owner ’ s manual carefully and keep it for future reference.
3 T ools Needed for Assembly One Phillips head screwdriver One wire stripper Six wire connectors (supplied) Three 60-watt (max.) candelabra base bulbs Materials Wiring, outlet box and box connectors must be of type required by the local code.
Preset Memory Feature Y our remote control receiver is equipped with a preset memory feature. The receiv- er will remember the light intensity and fan speed when the light and fan are turned off from the wall switch. When the wall switch is turned back on, the lights and fan will resume operation as they were prior to the switch being turned off.
2. Slide the four switch levers on the code switch to your choice of ON (up) or down positions. Use a ball-point pen or small screwdriver and slide the levers firmly up or down. 3. In the receiver (Figure 1), slide the four switch levers to the same positions as set in the transmitter .
6 It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tight- ened. Failure to verify that the pin and setscrews are properly installed (as shown in Figure 3) could result in the fan falling. ! W ARNING HAIRPIN CLIP DOWNROD CLEVIS PIN MOTOR COUPLIN G SETSCREW (2) Figure 3 3.
7 8. T urn the fan motor and housing assem- bly upside down in preparation for mounting the fan blade assemblies. Remove and discard the three shipping retainers securing the motor hub in the motor housing. NOTE: T ake care not to scratch the fan housing when installing the blade assemblies.
2. Carefully lift the fan and seat the hang- er ball/downrod assembly on the hang- er bracket that was just attached to the outlet box (Figure 1 1). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 10).
9 1. Position the supply wires to the left side of the outlet box (Figure 12); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 12. NOTE: Make all wiring connections using wire connectors (supplied).
7. Screw three 60-watt (maximum) cande- labra base flame bulbs into the light fitter sockets (Figure 15). 8. Unscrew the six ring screws from the lower ring assembly (Figure 15). Position the lower glass in the lower ring assembly so that the six channels in the glass align with the six arms of the lower ring assembly .
button is held down. When the light is at the desired brightness, release the button. 5. T o turn the light on and off, press and release the button. The light will turn on at the light level previously set (see step 4). 6. If airflow is desired in the opposite direction, turn the fan off and wait for the blades to stop turning.
12 Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. ! W ARNING The use of any other control not specifically approved for this fan could result in fire, shock and per- sonal injury .
13 T rouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker 1. Check main and branch start. blown. circuit fuses or circuit breakers. 2. Loose power line 2. Check line power connections connections to the fan, or to fan and wire.
14 Repair Parts 10 16 12 3 2 1 5 4 7 6 14 21 19 23 H I OFF LOW MED 24 11 15 13 9 17 20 25 8 22 18 BP7284, Sturbrige, KF180 7/31/06 10:52 AM Page 14.
Part Numbers Key Model No. Model No. Model No. N o . Description KF180AP01 KF180DBK01 KF180OZ01 * Hanger Pack, Consisting of: 761655-34 761655-36 761655-35 1 Hanger Bracket — — — 2 Hanger Ball .
LIMITED WARRANTY What The War ranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. Y ou must be the original purchaser or user of the product to be covered.
デバイスEmerson KF180の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Emerson KF180をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEmerson KF180の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Emerson KF180の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Emerson KF180で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Emerson KF180を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEmerson KF180の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Emerson KF180に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEmerson KF180デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。