EminentメーカーEM8622の使用説明書/サービス説明書
ページ先へ移動 of 23
EM8622 Wireless Control Panel.
2 | ENGLISH EM8622 - Wireless Control Panel Table of contents 1.0 Introduction ...... ...... ......... ...... ..... ...... ......... ...... ...... ..... ......... ...... ...... ...... ........ ...... .. 3 1.1 Packing content s ...... ......... ...... .
3 | ENGLISH 1.0 Introduction Congratulations w ith the purchase of thi s high-quality Eminent product ! This prod uct has undergone ex tensive testing by Eminen t’s technical ex perts. Should you experience any pro blems with this pro duct, you are covered by a five- year Eminent warranty.
4 | ENGLISH 1.3 Control panel ins ide 2.0 Installation Install the batteries and mount the control panel on the door fra me or the w all before use. Battery contact, plea se check positive and negativ.
5 | ENGLISH 1) Remove the screw and open the ca se 2) Install the batteries ac cording to th e positive and negative sign s (Re move the insulating strip be fore the first use) 3) Mount the backcover .
6 | ENGLISH If there is an intru sion the alarm sy stem will be trigger ed, the siren w ill hoot and the alarm sy stem will send an SMS and au to dial to pre-stored phone numbers to notify u sers. Note : When an en try delay is set, the external control pane l will NOT warn you with an audio signal when a sensor is t riggered.
7 | ENGLISH 3.2.2 Using RFID Tag to disarm If direct disar m by RFID tag is disa bled (this is the defaul t power saving mode when using batteries), u ser needs to press [* ] to wake up the control panel and then put RFID tag close to the reade r to di sarm the alar m system.
8 | ENGLISH 3.2.4 Emergency Call When the control panel is in SOS Speed Dial mode, u ser just holds the [SOS] key for 3 seconds, the LED indicator flashes once, the con trol panel beeps once, and the alarm system alar ms immediately.
9 | ENGLISH 4.0 Connect to the alarm sy stem Note : The default admin code is : 1 23456. See chapter “Ch ange Ad min Code” to change it. Note : The default user code is : 12 34. See chapter “Change User Code” to change it. Make sure the alar m system is in connection state (pres s code on alarm syste m and press the me mo button).
10 | ENGLISH 3. Put the RFID tag close to the RFID re ader. If one beep is heard the connecting is successful. When 2 beeps are hea rd, the RFID tag w as already connected to the control panel. To remove all conne cted RFID tag s, input the admin code followed by the # button.
11 | ENGLISH 6.0 Settings Before changing the settings of th e control panel, the control panel sho uld be in “setup-state”. 6.1 Enter Setup-s tate Note : The default adm in code is : 123456 Input the admin code fol lowed by the [#] button to w ake up the control panel.
12 | ENGLISH After setting a delay time, press the [Arm] button on the con trol pan el. The control panel will send the Arm command to the alarm system afte r the delay time you set in the control panel . Note : This setting will not apply to the Hom e mode.
13 | ENGLISH 6.3.1 Disable SO S code Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful. 6.3.2 Enable SOS code Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful.
14 | ENGLISH 6.4 Keyboard tone Keyboard tones can be switched o n or off. If they are switched of f, the beep when a setup is successful w ill also be swit ched off ! 6.4.1 Disable key board tone Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful.
15 | ENGLISH 6.5 Disarm system by RFID tag Users can enable or disable the function of d isarming the alar m system by RFID tag , or disarming silent by RFID tag. 6.5.1 Disable disar ming by RFID tag Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful.
16 | ENGLISH 6.5.3 Disarming silently by RFID tag The alarm panel an d siren will hoo t twice when disar ming the alarm system by RFID tag. If set disar ming silently by RFID tag, the alarm syste m and siren will keep silent when disarming.
17 | ENGLISH 6.6.1 Enable power savi g mode Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful. 6.6.2 Disable po wer saving mod e If the control panel is powered by an external 12V pow er supply (not included), i t is recommended to switch of the po wer saving mode.
18 | ENGLISH 6.7 Change user code A user can use its own code to wake up the control panel and send Ar m, Disarm or Home mode command s to the alarm syste m.
19 | ENGLISH 6.9 Reset the control panel After a reset the u ser code, admin code and all other setting s will be restored to default. Only the connected RFID t ags will remain wo rking. To remove the conne cted RFID tags, please refer to chapter “Connect RFID Tag to control panel”.
20 | ENGLISH 8.0 Service and su pport This user’s manual has been carefu lly written by Eminen t’s technical experts. If you have problems in stalling or using t he product, please fill out the support for m at the website www .eminent-online.com/supp ort .
21 | ENGLISH 9.0 Warning and p oints of attention Due to laws, directive s and regulat ions set out by the Europ ean parlia ment, some (wireless) devices could be subject to limitations concerning i ts use in certain European member states. In certai n European member states the use of su ch devices could be prohibited.
22 | ENGLISH 10.0 Warranty conditions The five-year Eminen t warranty ap plies to all Eminent produc ts, unless mentione d otherwise before or during the momen t of purchase. After buy ing a second -hand Eminent produc t the remaining per iod of warranty is measured from the moment of purchase by the produ ct’s initial ow ner.
23 | ENGLISH 11.0 Declaration of Conformity Application of Council Dire ctives: Manufacturer’s Na me: Eminent Type of Equip ment: Control panel Equipment Class: Commercial, Light Industrial, Cons umer PRODUCTNUM BER: EM8622 Conforms to the following standar ds: EN 301 489-1 V1.
デバイスEminent EM8622の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Eminent EM8622をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEminent EM8622の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Eminent EM8622の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Eminent EM8622で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Eminent EM8622を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEminent EM8622の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Eminent EM8622に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEminent EM8622デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。