ENCOREメーカーENRTR-104-2の使用説明書/サービス説明書
ページ先へ移動 of 41
High Speed Internet BroadBand Router User Guide.
.
FCC Warning This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection agai nst harmful interference when the equipment is operated in a commercial environ ment.
.
TABLE OF CONT ENT About This Guide ...................................................................................... 1 Purpose ............................................................................................. 1 Overview of this User’s Guide .
.
ABOUT THIS GUIDE Congratulations on your purchase of this 4-port Broadband Router. This device integrates 100Mbps Fa st Ethernet and 10Mbps Ethernet network capabilities in a highly flexible desktop package.
.
INTRODUCTION With the explosive growth of the Internet, accessin g information and services at any time, day or night has become a standard requirement for most people. The era of the standalone PC is waning. Networking technology is moving out of the exclu sive domain of corporations and into homes with at least two computers.
File sharing: Exchange data, messages, and distribute files thus making good use of hard disk space. Online gaming: Through the local area network, online gaming and e-commerce service s can be easily setup. Firewall: A built-in firewall function — for security and anti-hack system.
UNPACKING AND SETUP This chapter provides unpacking and setup information for the Broadband Router. Unpacking Open the box of the Broadband Router and carefully unpack it.
.
HARDWARE INSTALLATI ON Front Panel The figure below shows the front panel of the Broadband Router. Front Panel POWER This indicator lights green while the device is receiving power, otherwise, it is off. SYSTEM This indicator blinks green means the Internet Broadband Router is working successful.
Rear Panel The figure below shows the rear panel of the Broadband Router . Rear Panel WAN In the four port broadband router, there is an RJ-45 10/100Mbps Auto- MDIX port for the WAN that will fit the xDSL/Cable m odem’s specification need.
Connect the Internet Broadband Router 1. Plug in one end of the network cable to the WAN port of the 4-port Internet Broadband Router. 2. Plug in the other end of the network cable to the Ethernet port of the xDSL or Cable modem.
.
PC NETWORK TCP/IP SETTI NG The network TCP/IP settings differ based on the computer’s operating system (Win95/98/ME/NT/2000/XP) and are as follows. Windows 95/98/ME 1. Click on the “ Network neighborhood ” icon found on the desktop. 2. Click the right mouse button and a context menu will be show.
5. Select “ Disable DNS ” in the “ DNS ” field. 6. Select “ None ” for the “ Gateway address ” field. 12.
Windows 2000 Double click on the “ My computer ” icon on the desktop. When “ My computer ” window opens, open the “ Control panel ” and then open t he “ Network dialup connection ” applet. Double click on the “Local area network connection” icon.
Windows XP Point the cursor and click the right button on the “My Network Place” icon. Select “properties” to enter the TCP/IP setting window. 1. Set “ IP address ” to “ Obtain an IP address automatically .” 2. Set “ DNS ” to “ Obtain DNS server address automatically .
INTERNET B ROADBAND ROUT ER CONFIGURAT ION First make sure that the network connections are functioning nor mally. This Internet Broadband Router can be configured using Internet Explorer 4.
4. After entering the password, the main web page comes up, there are two choices for setting, Quick Setup or Advanced Setup, it is recommended that the beginner to use the Quick Setup, it will lead you step by step to configure the Broadband Router.
1-2 WAN Connection Type To select which the WAN connection type will be connected to, point the cursor to the Cable modem (DHCP), Fixed IP, or Dial-up xDSL (PPPoE) to process.
1-2-2 Fixed IP If the Internet Service Providers assign a fixed IP address, choose this option and enter the assigned IP address, subnet mask, gateway IP and DNS IP addresses for your Broadband Router.
demand button to dial up to the ISP when only on de mand, while there is a need of connecting to the ISP automatically. 1-2-4 PPTP If connected to the Internet using a (PPTP) xDSL Modem, enter the PPTP Account Name, PPTP Password, Host Name, Service IP Address, Your IP Address, Your Subnet Mask required by your ISP in the appropriate fields.
1-4 Status When finish configuring the Quick Setup, the Status screen will list up the connection status for the Broadband Routers' W AN/LAN interfaces, firmware and hardware version numbers, and the number of connected clients to the network.
Advance Setup The Broadband Router supports advanced fu nctions like System setting WAN setting, LAN setting, NAT Setting and Firewall setting. 2-1 System This page includes all the basic configuration tools for the Broadband Router. Point the selections in the left side of the menu screen.
z Remote Management from Internet To manage the Broadband Router from a remote location (outside of the local network through WAN port), it must specify the IP address of the remote PC, otherwise, leave the IP address 0.0.0.0, means all legal IP address can access the device.
2-1-4 Configuration Tools Use the "Backup Settings" tool to save the Broadband Router's current configuration to a file named "config.bin" on y our PC. You can then use the "Restore Settings" tool to rest ore the saved configuration of the Broadband Router that you set before.
2-1-5 Status Use the Status screen to se e the connection status for th e Broadband Routers' WAN/LAN interfaces, firmware and hardware version numbers, and the number of connected clients to the network. 2-1-6 System Log View any attempts that have been made to gain access to the network.
2-2 WAN The Broadband Router can be connected to the service provider in any of the following ways: Dynamic IP Address, Static IP Address, PPPoE and PPTP. 2-2-1 Dynamic IP The Host Name is optional, but may be required by some Service Providers. The default MAC address is set to the WAN's physical interface on the Broadband Router.
2-2-3 Dial-up xDSL (PPPoE) If connected to the Internet using a Dial-up xDSL (PPPoE) Modem, the ISP will provide a Password and Us er Name, and then the ISP uses PPPoE. Choose this option and enter th e required information, if the ISP provided a Service Name, enter it in the column of the Service Name field, otherwise, leave it blank.
2-2-4 PPTP If connected to the Internet using a (PPTP) xDSL Modem, enter the PPTP Account Name, PPTP Password, Host Name, Service IP Address, Your IP Address, Your Subnet Mask required by your ISP in the appropriate fields. If your ISP has provided you with a Connection ID, enter it in the Connection ID field, otherwise, leave it zero.
2-2-6 Dynamic DNS Dynamic DNS (Domain Name Service) is a method of keeping a domain name linked to a changing (dynamic) IP address. With most Cable and DSL connections, you are assigned a dy namic IP address and that address is used only for the duration of that specific connection.
2-3 LAN To configure the LAN’s IP Address and DHCP Service setting. 2-3-1 LAN Settings The default value is 192.168.1.1 for the IP address and 255.255.255.0 for the Subnet Mask. And you can also change the value for your needs. To enable the DHCP server for dy namic IP address allocation to the clients PCs, click the “Enable”.
2-4-1 Special Application Some applications require multiple connectio ns, such as Internet gaming, video conferencing, Internet telephony and others. These applications cannot work when Network Address Translation (NAT) is en abled.
Example: ID Trigger Port Trigger Type Public Port Public Type Comment 1 28800 UDP 2300-2400, 47624 UDP MSN Game Zone 2 28800 UDP 2300-2400, 47624 TCP MSN Game Zone 3 6112 UDP 6112 UDP Battle.net 2-4-2 Virtual Server Configure the Broadband Router as a virtual server to allow the Router to watch outgoing data for specific port numbers.
Example: ID Server IP Mapping Port Type Comment 1 192.168.2.20 80 TCP Web Server 2 192.168.2.12 20 TCP FTP Server 3 192.168.2.12 21 TCP FTP Server 4 192.
2-5-2 Client Filtering To block a certain client PCs accessing the Internet based on time. You can filter Internet access for local clients based on IP addresses, application types, (i.e., HTTP port), and time of day. For example, this screen shows that clients in the add ress range 192.
34.
TECHNICAL SP ECIFICATIO NS General Standards IE EE 802.3 10BASE-T Ether net IEEE 802.3u 100BASE -TX Fast Ethernet ANSI/IEEE 802.3 Auto-negotiation Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps .
デバイスENCORE ENRTR-104-2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
ENCORE ENRTR-104-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはENCORE ENRTR-104-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ENCORE ENRTR-104-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ENCORE ENRTR-104-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ENCORE ENRTR-104-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はENCORE ENRTR-104-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ENCORE ENRTR-104-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちENCORE ENRTR-104-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
