EnviroメーカーDV42DXの使用説明書/サービス説明書
ページ先へ移動 of 39
This appliance may be installed in an after market permanently located, manufactured (mobile) home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible f or use with other gases, unless a certied kit is used.
2 FOR SAFE INST ALLA TION AND OPERA TION OF Y OUR “ENVIR O” HEA TER, PLEASE CAREFULL Y READ THE FOLLO WING INFORMA TION: • All ENVIRO gas-red appliances must be installed in accor dance with their instructions. Carefully read all the instructions in this manual rst.
T able of Contents 3 Safety Precautions....................................................................................................2 T able of Contents............................................................................................
4 DIRECT VENT ONLY: This type is identied by the prex DV . This appliance draws all of its air f or combustion from outside the dwelling, through a specially designed v ent pipe system. This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above sea level.
Specific a tions INSTALLATION OPTIONS: • P arallel to a wall or placed in a corner • With a oor hearth or raised up the w all • Ducting to other rooms • V ertical or horizontal venting WARN.
6 WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE. P ILOT L IGHTING I NSTRUCTIONS : Figure 2. Lighting instruction label. CAUTION: Hot while operating. Do not touch.
Warning: Incorrect venturi adjustment may lead to improper combustion, which is a safety hazard. Contact the dealer if there is any concern about the venturi adjustment. NEVER USE AN OPEN FLAME FOR LEAK TESTING A IR D IVERTER C ONTROL : When the blower is on, the amount of air ow into the room can be adjusted with the air diverter .
Oper a ting Instructions B URNER L IGHTING : A) Make sure the pilot is lit. B) T urn gas control knob COUNTER CLOCKWISE to ON. C) Flip the burner switch to ON. D) T urn HI/LO knob to the desired ame height. E) T urn on all electrical power to the unit.
9 Maintenance And Ser vice R OUTINE M AINTENANCE : At least once a year , run through the following procedures to ensure the system is clean and working properly . Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not blocked by anything.
Maintenance And Ser vice C LEANING D ECORATIVE S URFACES : P ainted and porcelain faces should be wiped with a damp cloth periodically . If a plated face has been purchased, it should be unpacked/unwrapped carefully to avoid getting anything on the surface of the nish, including cleaners, polish and nger prints.
11 F UEL C ONVERSION : Warning: This conversion kit shall be installed by a qualied service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction.
Initial Inst alla tion QUALIFIED INST ALLERS ONL Y I NTRODUCTION : This section of the owner’s manual is for the use of qualied technicians only . Fireplace placement, hearths, facings, mantels, and venting terminations will be covered, as well as the gas and electric systems.
13 Initial Inst alla tion QUALIFIED INST ALLERS ONL Y C ORNER I NSTALLATION : The dimensions for installing a replace in the corner of a r oom are given below in Figure 11. R AISED F IREPLACES AND H EARTHS : There are a few options with raised replaces: raised with no hearth, raised with a raised hearth, or r aised with a oor level hearth.
Initial Inst alla tion QUALIFIED INST ALLERS ONL Y Protector pad, cement board and finishing material. Do not tile higher than this ledge Cement board Tile Protector Pad trim can be combustible as long as the hearth extends at least 12” (305 mm) in front of the replace and 1” (25 mm) on either side of the replace opening.
15 3" (89mm) 8" (203mm) mantel Combustibles Cement Board DV42DX 10" (254mm) 12" (305mm) 17" (432mm) 20" (508mm) 8" (203mm) mantel Combustibles Cement Board DV42DX with Manor 10" (254mm) 12" (305mm) 17" (432mm) Figure 18.
1 In accordance with the current CSA B149, Natur al Gas and Propane Installation Code. 2 In accordance with the current ANSI Z223.1 NFP A 54, National Fuel Gas Code. * These numbers are only estimates. Clearance in accordance with installation codes and the r equirements of the gas supplier .
Flue Pipe Adaptor W all Framing W all Thimble Fire Stop Exhaust 4" Flex Pipe Combusion Air 6 5/8" Flex Pipe Wire Spacers Horizontal V ent T ermination 17 INSTALLATION INSTRUCTIONS: 1.
through the outside wall f ar enough to connect onto the vent termination cap. 10. Apply a bead of Mill-P ac Black sealant to the top section of the Ø4” (10 cm) by 5” (12.5 cm) ue collar adaptor previously installed into the replace ue outlet.
19 Table 4: Vent part numbers (Must state if galvanized or black wanted, PART NUMBERS). Direct Vent GS Direct- Temp Secure Vent Ameri Vent Direct Description 908 4DT -6 SV4L6 6” pipe length 4D7 7”.
20 Initial Inst alla tion QUALIFIED INST ALLERS ONL Y V ENTING : This replace has been tested and certied for use with SIMPSON DURA VENT DIRECT VENT T YPE “GS” PIPE FOR GAS STOVES, SECURITY CHIMNEY’ S SECURE VENT DIRECT VENT SYSTEM kits, and MDV SELKIRK MET ALBESTOS .
5 4 3 2 1 0' (0m) 0' (0m) 1' (0.31m) 4' (1.22m) 4' (1.22m) 8' (2.45m) 10' (3.06m) 20' (6.1 1m) 30' (9.17m) V ent Restrict or Configuration Figure 25. Possible Vent Congurations V ent Restrictor P ositions 5 4 3 2 1 V ent Restrictor Figure 26.
W all framing Horizontal wall termination W all thimble fire stop Exhaust flex pipe Combustion air outer pipe Elbow Initial Inst alla tion QUALIFIED INST ALLERS ONL Y H ORIZONTAL T ERMINATION : NOTES: 1. Horizontal pipes must not be level. For every 12 inches (305 mm) of horizontal travel (away from the stove), there should be at least inch (6.
23 Initial Inst alla tion QUALIFIED INST ALLERS ONL Y Step 3. T o install the Round Support B ox/W all Thimble in a at ceiling, cut a 10 inch (25.4 cm) square hole in the ceiling, centered in the hole drilled in Step 2. Frame the hole as shown in Figure 24.
Initial Inst alla tion QUALIFIED INST ALLERS ONL Y STEP 5. Cut hole in the roof centered on the small hole placed in the roof fr om Step 2. The hole should be of sufcient size to meet minimum requirements for Clearance to Combustibles, as specied.
25 NOTES: (1) If an offset is necessary in the attic to avoid obstructions, it is important to support the vent pipe every 3 feet (914 mm), to av oid excessiv e stress on the elbows, and possible separ ation. W all straps are available for this purpose (see Figure 30).
F or the rst 24 inches (610 mm) of ducting, inch (13 mm) of clearance is required. After 24 inches (610 mm), the duct can be run with 0 inch (0 mm) clearance, though inch (13 mm) is preferred. T o avoid heat loss, insulate the duct whenev er it passes through an unheated area (i.
27 Initial Inst alla tion QUALIFIED INST ALLERS ONL Y E LECTRICAL R EQUIREMENTS : The replace must be electrical ly connected and grounded in accordance with local codes or , in the absence of local codes, with the current CSA C22.
Initial Inst alla tion G AS L INE C ONNECTION AND T ESTING : WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance. GAS LINE CONNECTION • This stove is equipped with a certied exible pipe located on the right side of the unit terminating in a ” male NPT tting.
29 Second ar y Inst alla tion B RICK L INER R EMOVAL : There are two (2) different brick liner sets; the ceramic set that comes with the unit or the optional cast iron set. The following instructions are f or both sets. WARNING: DO NOT INSTALL LINER IF UNIT IS HOT.
Second ar y Inst alla tion Right Log Figure 39: Shows the back log plus the two (2) small log twigs . Put the large back log in rst, making sure the locator pins line up with the cutout sections on the log. There are two (2) pins with ledges and a single ledge on the back log.
31 Figure 43: Final Log Set Arrangement with Embers. Left Log Center Log Second ar y Inst alla tion Figure 44: DV42DX Burning. Figure 42: Fourth Stage Log Set Installation. Figure 42: The left log rests on the left pin and ledge of the back log and the back of the andiron.
Second ar y Inst alla tion B URNER AND F AN R EMOVAL : 1. R emove brick liners, see steps 1 to 4 in S ECONDARY I NSTALLATION - B RICK L INER R EMOV AL . 2. The control panel is held in place with a T -20 screw on each end of the panel. Remov e the two (2) screws and the control panel.
33 T roubleshooting Problem Possible Cause Solution Spark wil l not light the pilot after r epeatedly pressing the spark ignitor Defective piezo ignitor • Check connections to ignitor . • If ignitor connections are good but no spark, replace ignitor .
P ar ts List - Components Reference Number Description Part Number 1 120°F (49°C) Ceramic F an T emperature Sensor EC-001 2 S.I.T . Nova V alve NG (50% turn down) EC-006 2 S.
35 P ar ts Diagr am - Components DV42DX - Components November 2004.
P ar ts List - Options Reference Number Options Part Number 1 The Lodge - Painted Char coal F ace With Plated Brushed Nickel Louvres & Knobs 50-534 The Manor Cast Iron Bay F ace - Painted 50-537 2.
37 P ar ts Diagr am - Options 1 2 3 4 5.
38 W arr anty Sherwood Industries Ltd. offers a Limited Lifetime Warr anty on this gas product. This Limited Lifetime W arrant y covers the appliance for a period of seven years from the date of installation. This warranty applies only to the original owner in the original location.
39 Inst alla tion Da t a Sheet The following information must be recorded by the installer for w arranty purposes and future ref erence. NAME OF OWNER: _________________________________________ ADDRES.
デバイスEnviro DV42DXの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Enviro DV42DXをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEnviro DV42DXの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Enviro DV42DXの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Enviro DV42DXで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Enviro DV42DXを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEnviro DV42DXの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Enviro DV42DXに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEnviro DV42DXデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
