EpsonメーカーC823301の使用説明書/サービス説明書
ページ先へ移動 of 17
C823301 Fax I/F Board User’s Manual.
Introduction This EPSON ® Fax Interface Board adds standalone plain paper fax reception to your EPSON laser printer. The Fax Interface Board is a G3 facsimile receiver and can be connected to any standard two-wire phone line.
Setup Setting up your fax board is a four-step process: 1. Set the DIP switches on the board. 2. Install the board in your printer. 3. Plug the appropriate cables into the board. 4. Perform a self test. Before you install your fax board, you need to make a number of choices about how your fax board will work.
Automatic reception Select this mode if you use the fax board with a telephone line that you use exclusively for fax reception. If you select Automatic reception mode, the board receives faxes automatically any time fax data is received and the printer it turned on.
Manual or software reception Select this mode if you want to connect the fax board to your computer and use fax sending and receiving software or if you use the fax board with a telephone line that you usually use for voice calls. In this mode, you receive a fax using your fax software or in the following manner: 1.
Once you have decided which fax reception setting you want, set the DIP switches according to the table below. This illustration shows the location of the switches; on is up and off is down.
There are three other settings you may want to change: Paper size The fax board can use either paper size shown below. SW 1-3 Functions I OFF Letter (default) ON A4 I Page overflow settings If the sen.
Installing the fax board in your printer After you have set the DIP switches, install the fax board in your printer following the instructions in your printer manual.
Fax modem mode If you want to use the fax board to send faxes from your computer, you need to buy a straight through serial (or modem) cable and appropriate fax modem software. One cable is included with your fax board, but you need an additional cable to connect the board to your computer.
Troubleshooting When the fax board cannot receive a fax The fax board has a 300KB buffer that allows it to store fax data when it can receive but not print.
o Other errors that can be corrected without turning the printer off. After these printer errors are corrected, the fax board starts to print the received fax data automatically.
Limitations EPL - 8000 users Set the following DIP switches if the fax board is installed in the EPL-8000. SW 2-l ON SW 2-2 OFF ActionLaser II users Set the printer emulation mode for the option interface card to the LJ-2 (Laser Jet) mode using SelecType.
Error Codes Error status report When an error occurs, the fax board prints a Fax Reception Error report, which includes an Error Code number. See the listing below for the meaning of the error code.
Technical specifications Facsimile reception Modem Facsimile V.29 9600bps, 7200bps V.27ter 4800bps, 2400bps T.30 (G3) Codec MH, MR Paper size A4, Letter (A4 mode on fax communication) Resolution Raster Feed 8.
Fax modem Modem V.29 9600bps, 7200bps V.27ter 4800bps, 2400pbs Modem commands EIA-578 (Fax class 1 compatible) Terminal speed NCU control 19200bps Auto / Manual Dial type Tone/Pulse Common specifications PTT line Two wires 3.
Connectors LINE (RJ-11: to telephone network) No. Signal I/O Comments 1 (N.C.) 2 (N.C.) 3 I PTT LINE (-48V / RING) 4 I PTT LINE ( EARTH / TIP) 5 (N.C.) 6 (N.C.) PHONE (RJ-11: to phone) No. Signal IlO Comments 1 (N.C.) 2 (N.C.) 3 0 PTT LINE (-48V / RING) 4 0 PTT LINE ( EARTH / TIP) 5 (N.
Serial interface cable PC side I/F card side Modular cable Serial cable DB-25 connector (DDK 17 JE-13250-02 compatible) Mini- DIN 9-pin (MSK EC-35-9P-C111 compatible) RJ-11 compatible Mini-DIN 9-pin t.
デバイスEpson C823301の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Epson C823301をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson C823301の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson C823301の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson C823301で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson C823301を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson C823301の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson C823301に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson C823301デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。