Alliance Laundry SystemsメーカーDishwasherの使用説明書/サービス説明書
ページ先へ移動 of 24
Para bajar una copia de estas instrucci ones en español, visite www.comlaundry.com. Keep these instructions for future reference. (If this machine changes ownership, this manual must accompany machine.) www.comlaundry.com Inst allation Instructions for S t acked W ashers and Dryers Dimensions .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 2 802715 IMPOR T ANT : Purchaser must consu lt the local gas supplie r for suggested instructions to be followed if the unit user smells gas.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 3 Dimensions SWD897N * With leveli ng legs turned into base. NOTE: Exhaust op enings are 4 inch (10.2 c m) metal ducting. SWD898N *With leveling legs turned into base. NOTE: Exhaust op enings are 4 inch (10.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 4 802715 Before Y ou St art Supplies For most installations, the basic supplies you will need are: Figure 1 NOTE: If the unit i.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 5 Inst allation Step 1: Position Unit Near Inst allation Area Move unit as close to the desired area of installation as possible. NOTE: For best performance and to minimize vibration or movement, install washer on a solid, sturdy and level floor .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 6 802715 NOTE: Use of the dispenser drawer or unit doors as a handle in the transportation of the unit may cause damage to the dispenser or doors. Place unit in position on a soli d, sturdy and level floor .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 7 Step 3: Connect Fill Hoses Wat e r Su p p l y W ater supply faucets must fit standard 3/4 inch (19.1 mm) female garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 8 802715 IMPOR T ANT : Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperatur e and constant high pressur e they are subject to.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 9 Step 4: Connect Drain Hose to Drain Recept acle Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose f rom the retainer clamp and by removing th e shipping tape.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 10 802715 Step 5: (Gas Dryer Only) Connect Gas Supply Pipe 1. Make certain your dryer is equipped for use with the type of gas in your laundry room. Dryer is equipped at the factory for Natural Gas with a 3/8 inch NPT gas connectio n.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 11 4. T ighten all connections securely . T urn on gas and check all pipe connections (internal & external) for gas leaks with a non-corrosive leak detection fluid.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 12 802715 Grounding Information • This dryer must be con nected to a grounded metal, permanent wiring system; or an equipment-grounding cond uctor must be run with the circuit conducto rs and connected to the equipment-grounding term inal or lead on the dryer .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 13 Connecting Power Cord with Three-Wire Plug NOTE: Four -wire cord is requir ed for mobile homes or where codes do not permit grounding through neutral. Figure 12 1. Disconnect power to dryer .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 14 802715 4. Use the three screws from the accessories bag to attach the power cord wir es to the terminal block.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 15 3. Remove ground screw and save for use in S tep 5. Remove wire and use in Step 6. Figure 18 4. Use a strain relief and insert end of power cord through power suppl y hole.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 16 802715 Step 7: Connect Dryer Exhaust System • DO NOT use plastic or thin foil ducting. Rigid metal duct is recommended. Refer to Figur e 21 . • Locate dryer so exhaust duct is as short as possible.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 17 Exhaust Direction The dryer can be exhausted to the ou tdoors through the back, left, right or bottom of the dryer . EXCEPT ION: Gas dryers cannot be vented out the left side because of the burner housing.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 18 802715 Step 8: (W asher On ly) Remove th e Shock Sleeves and Shipping Brace Remove front access panel by removing the two screws at the bottom of the panel. Remove the five bolts an d lockwashers from shipping brace with 9/16 inch wrench and remove brace.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 19 Step 10: Plug In the W asher and Dryer Electric Dryer Connect the dryer to an electrical pow er source.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 20 802715 Washer - All Models Except L TSA7A*N2989 W asher requires 120 V olt, 60 Hertz e lectrical supply and comes equipped with a 3-prong grou nding plug. Refer to serial plate for specific electrical requirements.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 21 When plugging in the washer: • DO NOT overload circuits. • DO NOT use an extension cord. • DO NOT use an adapter . • DO NOT operate both a washer and gas dryer on the same circuit.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 22 802715 After the dryer has operated fo r approximately five minutes, observe burn er flame through lower front panel. Adjust the air shutte r to obtain a soft, uniform blue flame.
.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT Inst aller Checklist Fast T rack for Inst alling the Unit (Refer to the manual for mor e detailed information) • Position Unit Near Installation Are a. 1 CHECK • Position and Level the Unit.
デバイスAlliance Laundry Systems Dishwasherの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Alliance Laundry Systems Dishwasherをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAlliance Laundry Systems Dishwasherの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Alliance Laundry Systems Dishwasherの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Alliance Laundry Systems Dishwasherで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Alliance Laundry Systems Dishwasherを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAlliance Laundry Systems Dishwasherの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Alliance Laundry Systems Dishwasherに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAlliance Laundry Systems Dishwasherデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。