EricssonメーカーLBI-39076Bの使用説明書/サービス説明書
ページ先へ移動 of 60
LBI-39076B ericssonz ericssonz System Manual EDACS Enhanced Local Interconnect (ELI).
LBI-39076B NOTICES Copyright September 1994, Ericsson GE Mobile Communications Inc. 2 REVISION HISTORY Revision Date Reason for Change - Sep 1994 Original Release (ELI Software Release 1.0) A Jan 1995 Revision D Main Board and Corrections B Feb 1996 Revision E Main Board, ELI Software Release 1.
TABLE OF CONTENTS LBI-39076 B 3 TABLE OF CONTENTS PAGE REGULATORY COMPLIANCE ............................................................................................................... 7 SPECIFICATIONS .............................................
LBI-39076B TABLE OF CONTENTS 4 TABLE OF CONTENTS (Cont.) PAGE CONFIGURATION .................................................................................................................................... 29 OVERVIEW ..............................
FIGURES LBI-39076 B 5 LIST OF FIGURES AND TABLES PAGE Figure 1 - Location of ELI Components in a Typical EDACS Installation ................................................. 10 Figure 2 - GTI Audio Paths ...............................................
LBI-39076B FIGURES AND TABLES 6 LIST OF FIGURES AND TABLES (Cont.) PAGE Figure 31 - MASTR II & IIe Connections ................................................................................................... 25 Figure 32 - PCM / Data Bus Cable .
REGULATORY COMPLIANCE LBI-39076 B 7 REGULATORY COMPLIANCE FEDERAL COMMUNICATIONS COMMISSION (FCC) REGULATIONS 1. This Telephone Interconnect, before its co nnection to a Telephone Central Office, mu s.
LBI-39076B REGULATORY COMPLIANCE 8 REGULATORY COMPLIANCE (Cont.) FEDERAL COMMUNICATIONS COMMISSION (FCC) REGULATIONS b. Incoming call is routed to a dial prompt. c. Incom ing call is routed to a recorded an nouncem ent th at can be adm inistered by the CPE (Customer Premise Equipment) user.
SPECIFICATIONS LBI-39076 B 9 SPECIFICATIONS Dimensions: Master GTI ........................................................... 1.75" H x 19.00" W x 12.00" D GTI ............................................................... 1.75" H x 19.
LBI-39076B INTRODUCTION / DESCRIPTION 10 INTRODUCTION This manual describes the installation, co nfiguration, and operation of the Enhanced L o cal Interconn ect (ELI) option.
DESCRIPTION LBI-39076 B 11 The Site Controller co mputer directs up to 16 levels of toll call restrictio ns, up to 15 r otary hunt sequences, 8 de- queuing priority levels, and inbound interconnect enable/disable assignm ents, for each ID num ber. It also accumu lates interconnect call activ ity data for the System Manager.
LBI-39076B DESCRIPTION / INSTALLATION 12 The telephone line interf ace provides the follow ing functions for radio-originated calls: • Applies signaling to seize telephone line. • Detects signaling from telephone line. • Generates and applies telephone number digits to telephone line.
INSTALLATION LBI-39076 B 13 Table 1 - Sequence of Installation Activities (with Step # References) Standard GTI Units Assign Record Software Set Up Set DIP Switches Mount with Connections Master GTI R.
LBI-39076B INSTALLATION 14 1. RADIO SOFTWARE The 1st step to install the ELI option applies o nly to MDR fu ll-du plex radios. If you plan to u se this ty pe of radio with your EL I system, m ake sure each radio contains 344A4271Gx softwa re (w here x = 2 or hig her).
INSTALLATION LBI-39076 B 15 The location of the Application Software and Personality PROMs on the PROM card is shown in Figure 7. When replacing PROMs, be su re to get each new PROM in the correct location an d the notched end facin g the right direction.
LBI-39076B INSTALLATION 16 You may use some other method. However, using the method described here assures that the supp lied cables will be the correct length and the PCM/Data Bus will be as short as possible. (The PCM/Data Bus mu st not exceed 120 feet in length).
INSTALLATION LBI-39076 B 17 Revision-D or E Main boards Revi si on - D or E M a i n boa r d s r eq u i r e ve r si on 2 . x or h igh er GTI 552 an d GTI DSP sof tware. Do not use v ersion 1. x GTI 552 o r GTI DSP soft wa r e wi t h r e vi s i on - D or E Ma i n boa r ds .
LBI-39076B INSTALLATION 18 6. GTI TELEPHONE INTERFACE The 6th step to install the ELI option is to configure each GTI telephone interf ace to match the type of telephone circuit to be connected to it.
INSTALLATION LBI-39076 B 19 End-to-End, Loop Start Ring Det. Loop Current Det. Trans- former Hybrid Send Rec Ring Tip K2 4 5 6 7 8 3 2 1 K3 JP3-B JP2-B JP15-A JP14-A JP8-A JP9-B JP13-A Audio Audio Figure 19 - End-to-End Loop Start (Rev A Main Board) Figure 19 show s the GTI telephone interface configured per Table 2 for End-t o-End, L oop Start.
LBI-39076B INSTALLATION 20 Table 3 - Configurations by Interface Characteristic (Rev A Main Board) INTERFACE JUMPER POSITIONS FOR JP1 THROUGH JP15 FUSES CHARACTERISTIC 1 2 3 4 5 6 7 8 9 10 1 1 12 13 1.
INSTALLATION LBI-39076 B 21 2 3 4 5 6 7 A B C D JP3 A B C D JP2 RING DET. 100 OHMS JP6 4.7 OHMS 4.7 OHMS 4.7 OHMS 4.7 OHMS JP5 8 620 OHMS FUSE F3 GND JP4 FUSE F2 -48 V 1 620 OHMS DS1 DS2 JP11 JP10 K3 A C B A B JP12 E-LEAD DET. JP8 JP1 A B JP9 K2 LOOP CURRENT DET.
LBI-39076B INSTALLATION 22 Revision-D or E Main Board The revis ion-D or E Main boards contain tw o jum p ers (JP3 and JP4) and a m atrix card connector (J5) to configu re the teleph one interf ace. Set the jumpers and insert th e Matrix card to m atch the type of telephone line to be connected to it.
INSTALLATION LBI-39076 B 23 Table 5 - Defined DIP Switch Settings for GTI Units 1 2 3 4 5 6 7 8 DIP SWITCH # 1 0 0 0 0 0 X X 0 1 0 0 0 0 X X 1 1 0 0 0 0 X X 0 0 1 0 0 0 X X 1 0 1 0 0 0 X X 0 1 1 0 0 0.
LBI-39076B INSTALLATION 24 9. GTI & IAM MOUNTING The 9th step to install the ELI option, is to mount the standard GT I units, the Master GTI, and op tional IAM (if supplied).
INSTALLATION LBI-39076 B 25 MASTR III Power Supply/Audio If the GTI unit is to be connected to a MASTR III repeater chan nel, connect a 19B803830P1 cable f rom the mal e 1x6- pin Molex connector on th.
LBI-39076B INSTALLATION 26 24-pin con nector on one end, an d a standard 24- pin connector on the other. To install the data bus cables, co nnect the IAM unit (if present) first, then the Master GTI unit, and finally the standard GTI units (from the lowest channel to the highest channel).
INSTALLATION LBI-39076 B 27 2#56022 601-0537 (C) ZETRON INC. U23 IAM V1.2 Software Version # Circuit Symbol Figure 35 - IAM Software Label 12. IAM CONNECTIONS The 12th step needed to install the ELI op tion app lies only if an IA M was supplied. All connectio ns to the IAM are m ade to connectors on the rear panel, as show n in Figure 36.
LBI-39076B INSTALLATION 28 be select ed using DIP switch sections 2 through 4 . The serial printer por t can be turned off and on using DIP switch section 5. The proper han dshaki ng protocol for y our printe r can be selected using DIP switch section 6.
CONFIGURATION LBI-39076 B 29 CONFIGURATION OVERVIEW The user configurable parameters for the ELI option reside in two locations: the Site Controller computer’s database and the GT I units’ d atabase. T h e configuration of these two databases is covered in this section.
LBI-39076B CONFIGURATION 30 Similarly , other interconnect timing parameters may need upward adjustment. In addition to the dial to ne detect duration, the following parameters m ay require changes: pulse digit delay base, pulse digit delay increment, DTMF digit delay, DTMF digit detect duration, an d line dropping duration.
CONFIGURATION LBI-39076 B 31 • Line Active - This colum n of parame ters defin es (for the site) if a line is available for interconnect calls. Default is no (N) for all lines. Enter Y for yes, or leave N for no. Note that a line number gets its number from the radio chann el num ber that shares the same GTI Unit.
LBI-39076B CONFIGURATION 32 Who Has What Priority • Interconnect - This 1-digit field defin es (for each logical unit ID) w hich of eight queuing priority levels (from 0 to 7) is to be app lied to this specific logical unit ID for interconnect calls.
CONFIGURATION LBI-39076 B 33 Who Has What Dedicated Line • Dedicated Line - This 3-digit field def ines (for each logical unit ID) the line number to be dedicated to outgoing interconnect calls. Default is line 1. Enter a line n um ber, or 0 for denial.
LBI-39076B CONFIGURATION 34 GTI Unit Office PC 1 1 2 2 3 3 DB-9 (F) Gnd Tx Data Rx Data DB-9 (M) Signal Ground Rx Data Tx Data COM Port Cable 19D903985P72 4 5 6 7 8 9 DTR CTS RTS 4 5 6 7 8 9 DTR RTS C.
OPERATION LBI-39076 B 35 OPERATION GTI UNITS The location o f the indicators and reset button o n the front panel of each GTI unit (includin g the Master GTI) is shown in Figure 43.
LBI-39076B OPERATION 36 with the Master GT I w ithin a couple of minutes of being powered-up, but in the event that it doesn’t, m omentarily press the button labeled “RESET”. CDR Received Indicator The red L ED labeled “ CDR RECEIVED” shoul d be lit mom entarily each time a Call Detail Record is receiv ed by the IAM.
OPERATION LBI-39076 B 37 Backup The IAM has the capacity to hold 60,000 records in battery back ed RAM. Every effort has been m ade to ensure that this m emory w on’t be corrup ted in normal operation.
LBI-39076B OPERATION 38 • Radio-originated call - a call from a radio using an EDACS repea ter site, through a telepho ne line connected to that EDA CS repeater site, to a telephone. • Line-connected GTI - the GTI unit connected to the telephone line for the interconnect call being described.
OPERATION LBI-39076 B 39 IDENTIFYING CALLED ID 13. T he channel-term inating GTI detects the first DTMF digit, momentarily lights the “DTMF DET ECTED” red LED on the front panel, and reports the digit to the Site Controller.
LBI-39076B OPERATION 40 PCM Data Bus (completing the audio path b etween the calling telephone and the called radio(s)). 28. The Site Controller directs the line- connected GTI to look for DTMF digits. ENDING THE CALL 29. T o end the telep hone interconnect call, the caller presse s the # key on the DT MF keypad and hangs up .
OPERATION LBI-39076 B 41 2. The radio sends an interconnect call request on the Control Channel. 3. The Control Channel GETC receives th e request for an interconnect call, and sends the request to the Site Controller.
LBI-39076B OPERATION 42 If the Dial Tone Required field is set to Y in the System Configuratio n of the GTI Configurato r, then the absence of dial tone, f or wh atever line ty pe (E&M or End-to-End), will cause the Site Controller to initiate a rotary hunt to get an available telephone line.
MAINTENANCE LBI-39076 B 43 MAINTENANCE GTI REMOVAL When y ou are about to rem o ve a GTI from an EDAC S Repeater cabinet in a w orking system , you mu st take special care to avoid disrupting th e system .
LBI-39076B MAINTENANCE 44 5. (Master GT I only) Disconnect the tw o Site Controller data link plugs from the back of the Master GTI. 6. Disconnect the PCM Data Bus f rom th e back panel of the GTI.
MAINTENANCE LBI-39076 B 45 Table 8 - Software Compatibility by Main Board Revision Number ELI EQUIPM- ENT CIRCUIT BOARD SOFTWARE PACKAGE SOFTWARE VERSION REQUIRED FOR MAIN BOARD REVISION NUMBER Revision A Revision D Revision E GTI Unit Main Board GTI DSP V1.
LBI-39076B MAINTENANCE 46 • Replace the GTI Master software on the GT I Interface Board with V1.04 GTI Master software. • Re-attach the top co ver, and re-install in cabinet (don’t forget to fasten rear supports).
MAINTENANCE LBI-39076 B 47 4. Each GTI in 1st Group (Modify 1st Group): • (MASTR II & IIe applications only ) - Add a jum per between pin s 2 and 3 of the Power/ Audi o plug on the back panel of the GTI (see Figure 45).
LBI-39076B MAINTENANCE 48 9. System Manager (Enable all but 2nd Group): • Using System Manager scre en 10, p anel 1 :4, reconfigu re the “Intercon nect” field to “Y” for the radio channels con nected to the Master GTI unit and each GTI unit in the first group.
MAINTENANCE LBI-39076 B 49 1. System Manager (Disable All): • Using System Manager scre en 10, p anel 1 :4, reconfigu re the Interconn ect field to N for each radio channel. • Using System Manager scre en 14, r econfigure the “Line Active” field to “N” for each line number.
LBI-39076B MAINTENANCE 50 If the EL I system experiences problems due to the temporary disconnections, you w ill have to d isable the ELI sy stem through the System Manager for each temporary disconnection.
MAINTENANCE LBI-39076 B 51 TROUBLESHOOTING The hardware u sed in the ELI sy stem is extremely reliable, making component failure the unlikely cause o f most problem s.
LBI-39076B TROUBLESHOOTING 52 Table 9 (Cont.) - Troubleshooting Symptoms SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION All radio-originated interconnect calls from all LIDs get rotary hunt tone after the dial tone is heard. The Site Controller’s personality does not contain the correct v alue for the Dial Tone Detect Duration parameter.
TROUBLESHOOTING LBI-39076 B 53 Table 9 (Cont.) - Troubleshooting Symptoms SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION All telephone-originated interconnect calls are unanswered on all lines. Site Controller com puter not connected to the Master GTI. Check 19B803826P1 and P2 dat a cable connections.
LBI-39076B TROUBLESHOOTING 54 Table 9 (Cont.) - Troubleshooting Symptoms SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION Billing data do es not contain the correct ID and channel information. Application Softw are in Site Controller compu ter does not support the EL I option.
GLOSSARY LBI-39076 B 55 GLOSSARY 2-Wire A udio Line....................................................... A 2- Wire audio line uses a sing le audio pair for passin g audio sign als in both directions. 4-Wire Audio Line ...............................
LBI-39076B GLOSSARY 56 GLOSSARY (CONT.) Ground-Start Signaling ................................................Ground-Start signaling is used to send the local off-ho ok and on-hook signals to the pub lic tel ephone network.
GLOSSARY / PARTS LIST LBI-39076 B 57 GLOSSARY (CONT.) Radio-Originated Call .................................................. A telephone interconnect call from a radio to a telephone. Site Controller Database ........................................
LBI-39076B INTERCONNECTION DIAGRAM ELI Interconnection Diagram 58 Site Controller Computer Port 30 RJ-45 Rx Data Tx Data Signal Ground 2 3 7 Port 31 RJ-45 Rx Data Tx Data Signal Ground 2 3 7 (Optional.
SCHEMATIC DIAGRAM LBI-39076 B ELI TELCO Module 19C852327G1 (Similar to 19D904451, Sh. 1, Rev. 0) 59 1 2 3 4 5 678 J1 RJ-45 J14 25-Pair 1 26 2 27 3 28 4 29 5 RJ-45 J2 678 123 45 RJ-45 J3 678 12345 J15 .
LBI-39076B INSTALLATION CHECKLIST Ericsson Inc. Private Radio Systems Mountain View Road Lynchburg, Virginia 24502 1-800-528-7711 (Outside USA, 804-528-7711) Printed in U.S.A. INSTALLATION CHECKLIST Steps 1 thro ugh 14 pa rallel the main headings in the Installatio n section of this manual.
デバイスEricsson LBI-39076Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ericsson LBI-39076Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEricsson LBI-39076Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ericsson LBI-39076Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ericsson LBI-39076Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ericsson LBI-39076Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEricsson LBI-39076Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ericsson LBI-39076Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEricsson LBI-39076Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
