Euphonixメーカー840-08758-02の使用説明書/サービス説明書
ページ先へ移動 of 20
Control Surface Manual Document Revision : 1.1 Part Number : 840-08758- 02 Release Date : Sep tember, 2003 Euphonix, Inc. 220 Portage Ave. Palo Alto, Californi a 94306 Phone: 650-855-0400 Fax: 650-855-0410 Web: http://www.euphonix.com e-mail: info@eupho nix.
In the interest of continued product development, Euphonix reserves the right to make improvements to this manual and the product it describes at any ti me, without notice or obligation.
IMPORTANT SAFETY INSTRUCTIONS The lighting flash with arrowhead symbol within an equilateral triang le, is intended to alert the user to the presence of uninsulated “da ngerous voltage” within the product’s enclosure that may be of sufficient magnitude to cons titute a risk of electrical shock to persons.
13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam.
Euphonix Max Air Contro l Surface Manual v Table of Contents System Startup Sequence ....... .................................................................. ................. 7 Description ................ ..........................................
Euphonix Max Air Contro l Surface Manual vi List of Figures 1 Typical Console Layout ...................................................................................................... 7 2 CM404 Rear Panel ..........................................
Euphonix Max Air Contro l Surface Manual 7 System Startup Sequence See page 21 in the Max Air Operation Manual for the system startup sequence. Description The Max Air Console consists of a configurable number of Control Modules that com- prise the Control Surfac e.
Euphonix Max Air Contro l Surface Manual 8 Rear Panels Figure 2 CM404 Rear Panel Figure 3 CM416 Rear Panel Power Connectors (IEC): Accepts two standard IE C power cords (provided). Two au- to ran gi ng switching supplies accept voltages between 100–240 VAC, 50–60 Hz.
Euphonix Max Air Contro l Surface Manual 9 Self Test Procedure The following pages describe the operation of standalone self-test software for the Max Air control modules. The self-test code is designed to be invoked in a module right after power-up and before the Single Board Computer (SBC) downloads code.
Euphonix Max Air Contro l Surface Manual 10 LED Test LED loop This switch cycles through all the LED colors. Color Toggle These switches light all the LEDs of each color: green, red, yellow, orange All LEDS This turns all LEDs on. NOTE: To avoid overheating, the module should not be left with All LEDS on for more than 5 minutes.
Euphonix Max Air Contro l Surface Manual 11 Display Test Clear All Char Up Char Down Char E Char W Enumerate Memory Test ROM Test This test reads the ROM and computes and displays the checksum . The user/tester can match the checksum to a known good checksum (s ee below) to make sure ROM test is successful.
Euphonix Max Air Contro l Surface Manual 12 Selecting and Adjusting the Onscreen Display The Touchscreen image controls are found on the panel behind the Touchscreen. If the image needs adjustment, access press the Menu button and follow the onscreen instructions.
Euphonix Max Air Contro l Surface Manual 13 Touchscreen Alignment The Max Air Touchscreen can be calibrated using the Elo Touchscreen utility. Note that different users may have slightly different wa ys of touching the screen. If an oper- ator finds they often miss onscreen obj ects, re-calibrate the touchscreen: 1.
Euphonix Max Air Contro l Surface Manual 14 Figure 8 3. Touch Align and follow the onscreen instructions. When asked to touch the target s on the screen, best results are achieved by touching the targets naturally without thinking too much a bout it. This aligns the touchscreen to an individual’s hand-eye coordination.
Euphonix Max Air Contro l Surface Manual 15 Changing the ID of a CM416 Module 1. Power cycle the module and then simult aneously press and hold the two lower knobs on the first strip befo re the module connects to the System PC (you have about 15 seconds).
Euphonix Max Air Contro l Surface Manual 16 Technical Specifications Power Voltage 90–254 VAC (RMS), 50/60 Hz Power Consumption 2 x 50 W per module 1.
Euphonix Max Air Contro l Surface Manual 17 Dimensions Figure 10 Side Dim ensions Figure 11 CM416 Bottom Dimensions 0 4.39 5.85 9.83 11.42 20.83 22.42 28.50 29.58 0 1.20 2.06 3.06 6.78 8.39 16.25 75.00° Dimensions in inches 15.625 CM416 BALANCE POINT 16.
Euphonix Max Air Contro l Surface Manual 18 Figure 12 CM404 Bottom Dimensions Figure 13 Max Air Top Dimension s .90 21.40 22.30 19.46 1.79 9.83 11.42 20.83 22.42 .53 VENTILATION FOR PROPER KEEP CLEAR 0 0 1/4-20 THREADED INSERT 8 PLACES 8.742 0.00 0.00 35.
Euphonix Max Air Contro l Surface Manual 19 User Reference Internal Components Figure 14 CM404 Figure 15 CM416 Dual Power Connections Dual Power Supplies KVM Extender Power Distribution Single Board C.
Euphonix Max Air Contro l Surface Manual 20 Fans The CM416 modules have low-noise internal fans and a thermal sensor between the displays on strips five and six. If a module ge ts too hot, the fans automatically turn on at a low or high speed depending on the temperature.
デバイスEuphonix 840-08758-02の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Euphonix 840-08758-02をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEuphonix 840-08758-02の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Euphonix 840-08758-02の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Euphonix 840-08758-02で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Euphonix 840-08758-02を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEuphonix 840-08758-02の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Euphonix 840-08758-02に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEuphonix 840-08758-02デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
