Alliedメーカー(2の使用説明書/サービス説明書
ページ先へ移動 of 14
506248-01 Page 1 of 14 Issue 0902 Save these instructions for future reference INST ALLA TION AND MAINTENANCE INSTRUCTIONS (2,4)PHP(13,15) Series Self-Contained Heat Pump Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage.
Page 2 of 14 506248-01 Issue 0902 INST ALLA TION These instructions explain the recommended method of installation of the PHP heat pump unit and associated electrical wiring. This unit is designed and approved for use as a self- contained air-to-air outdoor heat pump system.
506248-01 Page 3 of 14 Issue 0902 Using Accessory Lif t Kit Figure 1 Units may also be moved or lifted with a forklif t while still in the factory-supplied packaging.
Page 4 of 14 506248-01 Issue 0902 Ductwork Ductwork should be designed and sized according to the methods in Manual Q of the Air Conditioning Contractors of America (ACCA). A closed return duct system shall be used. This shall not preclude use of economizers or outdoor fresh air intake.
506248-01 Page 5 of 14 Issue 0902 Power supply to the unit must comply with all applicable codes and the National Electical Code (NEC) or Canadian Electrical Code (CEC). A fused disconnect switch should be field provided for the unit. The switch must be sep arate from all other circuit s.
Page 6 of 14 506248-01 Issue 0902 Thermostat The room thermostat should be located on an inside wall where it will not be subject to draft s, sun exposure, or heat from electrical fixtures or appliances. Follow the manufacturer ’ s instructions enclosed with thermostat for general installation procedure.
506248-01 Page 7 of 14 Issue 0902 OPERA TION Sequence of Operation Cooling When the thermostat is in the cooling mode, the O circuit is powered which energizes the reversing valve. Upon cooling demand, the thermostat closes circuit R and Y . Closing R and Y closes the unit cont actor , starting the compressor and outdoor fan.
Page 8 of 14 506248-01 Issue 0902 jumper is not in place, the control defaults to a 90-minute defrost interval. The maximum defrost period is 14 minutes and cannot be adjusted. A test option is provided for troubleshooting. The test mode may be started any time the unit is in the heating mode and the defrost thermostat is closed or jumpered.
506248-01 Page 9 of 14 Issue 0902 There is no blower “on” delay after a call for heating or cooling. Blower “off” delay is 90 seconds af ter the thermostat is satisfied. V ariable Speed Motor Units equipped with a variable speed circulation air blower motor will deliver a constant airflow within a wide range of external static pressures.
Page 10 of 14 506248-01 Issue 0902 Owner Record Model # _________________________________ Serial # _________________________________ Installation Date ___________________________ Installed by: Dealer .
506248-01 Page 11 of 14 Issue 0902 Figure 9 208/230V -1-60 G W1 CR O BLK RED YEL RED CONT ACT OR THERMOST A T HIGH PRESSURE SWITCH (IF USED) L1 T1 T2 L2 C H F CONDENSER F AN MO TOR COMPRESSOR CONT ACT.
Page 12 of 14 506248-01 Issue 0902 Connection Diagram Single Phase – V ariable Speed Motor P/N 48374-001 Figure 10 DIAGNOSTIC DISPLA Y Note: Because the pressure switches are monitored only when "Y1" (Input) is activ e, the code for pressure s witch open will not be seen when "Y1" is off .
506248-01 Page 13 of 14 Issue 0902 ALLIED AIR ENTERPRISES EQUIPMENT LIMITED W ARRANTY APPLIES IN U.S.A. AND CANADA ONL Y F AILURE T O MAINT AIN YOUR EQUIPMENT WILL VOID THIS W ARRANTY COVERED EQUIPMEN.
Page 14 of 14 506248-01 Issue 0902 Allied Air Enterprises Inc. (“Allied Air”) provides its air conditioning and heating product s with a S tandard Limited Parts W a rranty for five (5) years.
デバイスAllied (2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Allied (2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAllied (2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Allied (2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Allied (2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Allied (2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAllied (2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Allied (2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAllied (2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
