Extron electronicメーカーHSA 802の使用説明書/サービス説明書
ページ先へ移動 of 25
User ’ s Manual Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Extron Electronics, Europe Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.33.453.4050 Extron Electronics, Asia 135 Joo Seng R oad, #04-01 PM Industrial Building Singapore 368363 +65.
Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock.
i Surface Access Products • Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About the HSA Hideaway Enclosures ......................... 1-2 Features ........................................
ii Surface Access Products • Table of Contents T able of Contents, cont’d Surface Access Products 1 Chapter One Intr oduction About the HSA Hideaway Enclosures Features.
Surface Access Products • Introduction Surface Access Products • Introduction Intr oduction About the HSA Hideaway Enclosure s The Extron Hideaway HSA 800 and HSA 802 are furniture- mounted, architectural solutions for inconspicuous computer video interface connector access and control.
Surface Access Products • Introduction Surface Access Products • Introduction Intr oduction 2 Chapter T wo Installation Installation Overview Preparing the Routing Template Preparing the Table and.
Surface Access Products • Installation Surface Access Products • Installation Installation 2-3 These strips raise the routing template above the mounting surface to provide room for the r outer ’s collar , protect the mounting surface, and extend the reach of the routing template so that it can be clamped to the edge of the surface.
Surface Access Products • Installation Surface Access Products • Installation Installation, cont’d 2-5 2-4 template, you will cut an improperly-sized hole. If you use a larger template than r equir ed, the cut will r esult in gaps in the table surface on either side of the enclosure.
Surface Access Products • Installation Surface Access Products • Installation Installation, cont’d 2-6 Mounting Surface Clamshell Full Thread Mounting Bolts AAP Cables Flat W asher IEC P ower Co.
Surface Access Products • Installation Surface Access Products • Installation Installation, cont’d 2-8 needed, four spare screws ar e stored in the underside of the enclosure .
Surface Access Products • Installation Surface Access Products • Installation Installation, cont’d If necessary , on the front panel, have a qualified service person replace the connector icon by prying the old icon of f of the connector plug-in with a tweeker (figure 2-9) and snapping a new icon in place.
Surface Access Products • Installation Installation, cont’d Surface Access Products 3 Chapter Thr ee Maintenance and Modifications Replacing an AAP Replacing the Bezels Removing and Replacing the .
Maintenance and Modifications Surface Access Products • Maintenance and Modifications Surface Access Products • Maintenance and Modifications 3-2 The HSA 800 and HSA 802 surface mount enclosures can be modified in the future to replace an AAP or to add a second connector panel (with all of the associated cables) to an HSA 800.
Surface Access Products • Maintenance and Modifications Surface Access Products • Maintenance and Modifications Maintenance and Modifications, cont’d 2 . W ith a tweeker , push down on and gently twist on the front of each RJ-45 connector detent to disconnect the connector from the r ear of the front panel plug-in.
Surface Access Products • Maintenance and Modifications Surface Access Products • Maintenance and Modifications Maintenance and Modifications, cont’d Mounting Surface Clamshell Full Thread Mounting Bolts AAP Cables Flat Washer IEC P ower Cord RJ-45 Connectors Shroud HSA 802 Remove 16 screws 1 2 5 - 5 0 / 6 0 H z 0 .
Surface Access Products • Maintenance and Modifications Surface Access Products • Maintenance and Modifications Maintenance and Modifications, cont’d 1 . Remove the surface mount enclosure. See Removing and Replacing the Enclosure , steps 1 through 9 .
Surface Access Products • Maintenance and Modifications Surface Access Products • Maintenance and Modifications Maintenance and Modifications, cont’d 3-10 frame. Carefully draw the gas lift out thr ough the top of the enclosure frame. 6 . Insert the shaft end of the r eplacement gas lift through the hole in the lifting platform.
Surface Access Products • Maintenance and Modifications Maintenance and Modifications, cont’d Surface Access Products A Appendix A Reference Information Specifications Part Numbers Included Parts .
Surface Access Products • Reference Information Surface Access Products • Reference Information Reference Information A-3 A-2 Specifications General Rack mount .................... No, but furniture mountable Enclosure type ............... Metal Enclosure approximate dimensions Top pla te (outer rim) .
Surface Access Products • Reference Information Surface Access Products • Reference Information Reference Informati on, cont’d -or - A-4 HSA 800/802 EU Part number HSA 802 EU Enclosure (po lishe.
Surface Access Products • Reference Information Surface Access Products • Reference Information Reference Informati on, cont’d A-6 T op Plate Dimensions The cut-out template (figure A-2) is not to scale and is for refer ence only .
Surface Access Products • Reference Information Reference Informati on, cont’d Surface Access Products B Appendix B Packaging for Shipment Page intentionally left blank A-8.
The HSA 800’s and HSA 802’s ultra-fine machined surfaces and moving parts make them vulnerable to damage caused by mishandling during shipment if they are improperly packaged. If, for any reason, you need to r eturn an HSA to Extr on, first contact Extron to obtain a r eturn kit.
Surface Access Products • Packaging for Shipment Surface Access Products • Packaging for Shipment Packaging for Shipment, Cont’d 6 . Release (extend) the top panel. 7 . Insert the HSA 800/802 and the clamshell into one of the foam shells (figure B-4).
Surface Access Products • Packaging for Shipment Packaging for Shipment, Cont’d B-6 Page intentionally left blank.
デバイスExtron electronic HSA 802の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Extron electronic HSA 802をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはExtron electronic HSA 802の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Extron electronic HSA 802の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Extron electronic HSA 802で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Extron electronic HSA 802を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はExtron electronic HSA 802の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Extron electronic HSA 802に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちExtron electronic HSA 802デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。