FeddersメーカーCH18ABD1の使用説明書/サービス説明書
ページ先へ移動 of 8
Installation, Oper ation and Maint enanc e 1.5 Thr oug h 5 T on H eat P ump INTRODUCTION ..............................................................................1 NOTES TO INST ALLER ..............................................................
NOTES TO INST ALLER The words “SHALL” and “MUST” indicate a requirement which is essential to satisfactory and safe product performance. The words “SHOULD” and “MA Y” indicate a recommendation or advice which is not essential and not required but which may be useful or helpful.
2 Six feet clearance above the unit Three feet clearance Rain Gutters Concrete slab Three feet clearance INST ALLA TION Condensing Unit Location The condensing unit should be located outdoors as close as possible to the evaporator .
Opening the Service V alve (Step V alve) NOTE: This is not a back-seating valve. 1. Remove the valve cap using an adjustable wrench. 2. Open the valve by inserting a hex wrench (3/16" for the liquid line, 5/16" for the vapor line) into the stem and back out counter-clockwise until the valve stem just touches the retaining ring.
4 CONNECT REFRIGERANT PIPING The following should be followed when installing refrigerant piping. Comply with all local, state, and federal codes and/or r egulations pertaining to this type of equipment and its installation. 1. Run the tubing by the most direct route and support every few feet.
Mo d e l 5 FINAL CHECKS FOR INST ALLER 1. Ensure that all wiring is routed away from tubing and she et metal edges to prevent rub-through or wire pinching. 2 . Ensure that all wiring and tubing is secure in unit before adding panels and covers. 3. Tighten service valve stem caps to 1/12 turn past finger tight.
6 24 AB 1 VF D CH 18 = 18000 BTU/H [5.28 kW] 24 = 24000 BTU/H [7.03 kW] 30 = 30000 BTU/H [8.79 kW] 36 = 36000 BTU/H [10.55 kW] 42 = 42000 BTU/H [12.31 kW] 48 = 48000 BTU/H [14.
M odel C10 & This W arranty Does Not Cover Damage Caused By: • Improper installation • Misuse of equipment • Negligent servicing • Improper applications • Preventative maintenance • Un.
デバイスFedders CH18ABD1の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Fedders CH18ABD1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFedders CH18ABD1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fedders CH18ABD1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fedders CH18ABD1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fedders CH18ABD1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFedders CH18ABD1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fedders CH18ABD1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFedders CH18ABD1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。