Ferrisメーカー1000z Seriesの使用説明書/サービス説明書
ページ先へ移動 of 19
OPERA TOR’S MANUAL 22860 Rev. 9/2001 TP 100-7040-01-AT-FD with Blower Setup Instructions Double & T riple Bag Grass Collection Systems Double Bag Collection System for: Ferris 1000Z Series - 48.
Ferris Industries 5375 North Main Street Munnsville, NY 13409 800-933-6175 www.ferrisindustries.com © Copyright 2001 Ferris Industries All Rights Reserved. Printed in USA. FERRIS LIMITED W ARRANTY IMPORT ANT This warr anty shall apply ONL Y if the warranty registr ation f or m has been completed and retur ned to F erris Industr ies, Inc.
1 I I N N I I T T I I A A L L I I N N S S T T A A L L L L A A T T I I O O N N & & A A S S S S E E M M B B L L Y Y 6 6 1 1 ” ” T T R R I I P P L L E E B B A A G G C C O O L L L L E E C C T .
2 Read and obey all operation and warning decals. DANGER ROTATING CUTTING BLADE Do not operate mower without deflector or entire grass catcher in place.
3 BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged.
4 Initial Installation & Assembly Remove Disc harge Chute 1. Park machine on a flat, level surface and apply the parking brake. 2. Remove the discharge chute and save. Save springs and spacer (Derby Colt only). 48” & 52” DOUBLE-B A G COLLECTION SYSTEM BLO WER MOUNT & DRIVE GR OUP Figure 1.
5 Install Spindle Pulley 1. Apply an anti-seize compound to the spindle shaft. Install the new, double spindle pulley (C, FIgure 4) on the shaft with the smaller pulley facing up with the 5/8 ” nylon lock nut (A), 5/8 ” washer (B) and 1/4 ” key (D) and tighten to 85-95 ft.
6 2. While holding the mount plate vertical and against the chute mount tabs, place the spacers on the mower deck in the recesses of the mount plate. Make sure they are at the bottom of the recess (see Figure 7). Mark their location with a paint pen or prick punch.
7 Blower Preparation 1. Remove the belt guard (A, Figure 9) and hardware (B & C) from the blower housing and set aside. NOTE: Record the model and serial number of the blower on the warranty registration card and in the space provided on Page 1. The serial tag is located on the outside face of the blower housing.
8 Figure 11. Install Bearing & Eyebolt A. 7/16 ” x 1-1/2 ” Capscrew (4) E. 1/4 ” Washer B. Bearing F. 1/4 ” x 1 ” Eyebolt C. 7/16 ” Nylon Lock Nut (4) G. Spring D. 1/4-20 Nylon Lock Nut H. 5/16-18 Nylon Lock Nut Figure 12. Install Blower Pulley & Guide Bolt 6.
9 Figure 14. Install Blower & Belt Guard Install Blower & Belt Guar d 1. Install the blower onto the chute mount tabs with the blower mount tabs towards the rear. Secure with the retainer pin and hair pin. Make sure the handle of the retaining pin is pointing down.
10 Initial Installation & Assembly Remove Disc harge Chute 1. Park machine on a flat, level surface and apply the parking brake. 2. Remove the discharge chute and save. Save springs and spacer (Derby Stallion only). Release Mower Drive Belt T ension 1.
11 Install Spindle Pulley 1. Apply an anti-seize compound to the spindle shaft. Install the new, double spindle pulley (C, Figure 22) on the shaft with the smaller pulley facing up with the 5/8 ” nylon lock nut (A), 5/8 ” washer (B) and 1/4 ” key (D) and tighten to 85-95 ft.
12 61” Blower Mount & Drive Installation Blower Preparation 1. Remove the belt guard (A, Figure 24) and hardware (B & C) from the blower housing and set aside. NOTE: Record the model and serial number of the blower on the warranty registration card and in the space provided on Page 1.
13 Figure 26. Install Bearing & Spring A. 7/16-14 x 1-1/2 ” Bolt E. 5/16-18 Flange Nut B. Bearing F. 5/16-18 Nylon Lock Nut C. 7/16-14 Nylon Lock Nut G. Spring D. 5/16-18 x 1-1/4 ” Bolt Figure 27. Install Support Rail & Spring A. Deck Support Rail C.
14 Figure 28. Install Blower Brace A. Blower Brace B. 3/8-16 x 1 ” Bolt C. 3/8 ” Washer Figure 29. Install Blower Pulley & Guide Bolt 11. Loosely install the blower brace (A, Figure 28), 3/8- 16 x 1 ” bolts (B) and 3/8 ” washers (C) as shown.
15 Figure 31. Install Blower A. 3/8-16 x 1 ” Bolt D. 3/8-16 Flange Nut B. Mount Bar E. 3/8-16 x 1 ” Bolt C. 3/8-16 X 1 ” Bolt Figure 32. Install Belt Shield & Clevis Pin A. 3/8 ” x 4 ” Clevis Pin D. Belt Shield B. Plastic Cap E. Plastic Knob C.
16 Discharge Chute Reattachment MO WING WITHOUT THE BLO WER For operation without the blower, the deflector must be properly installed in the down position and retained by the spring latch (Derby models only). To remove the blower, reverse the installation steps.
T or que Specification Char t FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
デバイスFerris 1000z Seriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ferris 1000z Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFerris 1000z Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ferris 1000z Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ferris 1000z Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ferris 1000z Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFerris 1000z Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ferris 1000z Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFerris 1000z Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。