Fisher & PaykelメーカーDD603Iの使用説明書/サービス説明書
ページ先へ移動 of 12
open 5 / 16 (8mm) gap between panels BEFORE YOU ST ART FOR INTEGRA TED DOUBLE MODELS DD603I (NOTE: FOR SINGLE R MODELS, REFER TO BACK OF THIS BOOK) DOUBLE R INTEGRA TED P ANEL PREP ARA TION part numbe.
BEFORE YOU ST ART P ARTS SUPPLIED INTEGRA TED P ARTS KIT part no. 526674 P anel Preparation Booklet (1) TOOLS NEEDED Safety Glasses, T ape Measure, P encil, Needle-Nose Pliers, Drill & Phillips Bit or Phillips Screwdriver , ø 1” (25.4mm) Boring Bit or ø 1” (25.
R READ THESE INSTRUCTIONS COMPLETEL Y AND CAREFULL Y . BADGE AND HANDLE POSITIONS On both P anels, select the Badge position to suit the cabinetry design, within the available badge zones. The Badge may be centered on the edge of the badge zone. The handle position will also need to be taken into account.
FITTING THE HANDLE Fit the customer supplied handle. WARNING! When mounting the handle, be sure fastenings do not protrude beyond the back surface of the P anel. FITTING THE BADGE Fit a Badge to each P anel by feeding the wires through to the back and pressing the Badge into the cut out.
R P ANEL PREP ARA TION INSTRUCTIONS STEP 5: SECURING THE TOE KICK P ANEL STEP 6: GROUNDING THE MOUNTING BRACKETS AND CONNECTING THE BADGE WIRES WARNING! Be sure the Product is not plugged in. Important! The Badge Isolator Board is an electrostatic sensitive device.
R P ANEL PREP ARA TION INSTRUCTIONS STEP 7: FITTING THE P ANELS TO THE PRODUCT 6 Fit the assembled P anels by sliding in an inwards and upwards motion. The rubber seal between the Drawer and P anels must be kept in place. Secure the P anels by inserting the pins on either side of the Drawer .
open 3 / 8 (9mm) gap between panels BEFORE YOU ST ART FOR INTEGRA TED SINGLE MODELS DS603I (NOTE: FOR DOUBLE MODELS, REFER TO BACK OF THIS BOOK) SINGLE INTEGRA TED P ANEL PREP ARA TION part number 526.
BEFORE YOU ST ART IMPORT ANT INTEGRA TED P ANEL THICKNESS P anel minimum thickness is 16mm. P anel thicknesses above 18mm can be accommodated but product depth will increase accordingly . INTEGRA TED P ANEL MA TERIAL Drawer F ront material must be suitable for damp conditions (122 o F/50 o C @ 80% RH) or adequately sealed to withstand moisture.
READ THESE INSTRUCTIONS COMPLETEL Y AND CAREFULL Y . BADGE AND HANDLE POSITIONS On both P anel, select the Badge position to suit the cabinetry design, within the available badge zone. If required, the Badge may be centered on the edge of the badge zone.
P ANEL PREP ARA TION INSTRUCTIONS 4 The Mounting Bracket is directly screwed to the back of the Integrated P anel. On a soft surface centralize and align the Mounting Bracket on the P anel. Important! For some materials pilot holes may need to be drilled first before screwing the Mounting Bracket onto the P anel.
P ANEL PREP ARA TION INSTRUCTIONS STEP 5: GROUNDING THE MOUNTING BRACKETS STEP 6: CONNECTING THE BADGE WIRES WARNING! Be sure the Product is not plugged in.
P ANEL PREP ARA TION INSTRUCTIONS STEP 7: FITTING THE P ANELS TO THE PRODUCT 6 Fit the assembled P anel by sliding in an inwards and upwards motion. The rubber seal between the Drawer and P anel must be kept in place. Secure the P anel by inserting the pins on either side of the Drawer .
デバイスFisher & Paykel DD603Iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Fisher & Paykel DD603Iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFisher & Paykel DD603Iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fisher & Paykel DD603Iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fisher & Paykel DD603Iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fisher & Paykel DD603Iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFisher & Paykel DD603Iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fisher & Paykel DD603Iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFisher & Paykel DD603Iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
