Fisher & PaykelメーカーDS602Iの使用説明書/サービス説明書
ページ先へ移動 of 20
DS602 I (Integrated) Models DS602 DS602 I DS602 (Prefinished) Part No. 599066/D USA.
Single DishDrawer Table of Contents Section 1 General Information 1.1 Preparation 1.2 Product Specifications & Cavity Dimensions 1.3 Options for Installing Multiple Products 1.4 Electrical, Plumbing & Drainage Information 1.5 Product Parts 1.6 Additional Product Parts for Integrated DishDrawer Section 2 Fitting the DishDrawer 2.
Weight - Full 93lb (42kg) Prefinished - Empty 62lb (28kg) Prefinished Electrical 110-120VAC 3 pin socket outlet Drying Residual Heat & Fan Assisted Water Connection Recommended Hot 140 ° F (60 ° C) Max. Water Pressure Maximum 139 p.s.i. (960 kpa) Minimum 4.
Page DS_03 Where the DishDrawer is in an under counter situation, i.e. built into a kitchen unit, it is recommended that bare wood surrounding the DishDrawer is sealed with an oil based paint or polyurethane to prevent possible steam damage. IMPORTANT IMPORTANT STEP 1.
Note: DS602 Prefinished Model is shown. There is no variation in plumbing between DS602 Prefinished Model and DS602I Integrated Model. Options 1 and 2 are the preferred options. PLUMBING - DRAINAGE OPTIONS Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Page DS_05 STEP 1.5 PRODUCT PARTS Tools Needed To Install DishDrawer Wooden Chopping Board Level Safety Glasses Utility Knife Pencil Drill & Drill Bits ( 3 / 32 ", 9 / 16 " & 11 / 32 ") (2.
SECTION 2 FITTING THE DISHDRAWER Ensure the cavity is at least 22 7 / 8 " (580mm) deep. TIP STEP 2.1 DISHDRAWER MOUNTING HOLE LOCATIONS 2.1.1 Draw the cavity center line on the supporting cabinetry. 2.1.2 Center Template in cavity using V-notch on the front of the Template.
STEP 2.2 CONNECTING THE SERVICES Ensure the edges of the Service Hole are smooth or covered. (See Step 1.2 - Product Specifications & Cavity Dimensions.) If the Services Hole is through a metal partition, the hole must be protected with the Edge Protector provided.
The Product MUST NOT be plugged in at this stage. WARNING 2.2.6 If required, trim the Single Connector to the size which matches the waste tee or air break to be used. There are ribs provided to guide cutting. When using the Single Connector, the hose should be pushed in firmly, 5 clicks.
STEP 2.3 FLEXIBLE EXTRUSION ATTACHMENT FOR 24 (610mm) CAVITY Wiring, Plumbing and Services should be completed before attaching the flexible extrusion. TIP 2.3.1 Flexible Extrusions are supplied to enable the installer to help fill any excess space between the sides of the DishDrawer and the cavity.
SECTION 3 DO NOT push against the middle of the drawer. The DishDrawer should not support any part of the kitchen cabinetry. WARNING Make sure the inlet and drain hose and main flex are not restricted or damaged by carefully pulling them through the Services Hole as the DishDrawer is being pushed back into the cavity.
Recommended Drawer Front thickness for Integrated product is 5 / 8 " to 3 / 4 " (16mm - 18mm). IMPORTANT SECTION 4 INFORMATION FOR CABINET MAKER FOR INTEGRATED DISHDRAWER STEP 4.1 INTEGRATED DRAWER FRONT DIMENSIONS Drawer Front material must be suitable for damp conditions or adequately sealed to withstand moisture.
A minimum clearance of 3 / 32 (2.5mm) must be maintained between the Drawer Front and existing cabinetry, except between the underside of the Drawer Front and the shelf, where a 1 / 4 (6mm) clearance is needed for product venting.
Accuracy is essential when cutting the Badge Mounting Hole to ensure a neat fit to hold the badge. IMPORTANT IMPORTANT All marking out to be done on the back surface of the Drawer Front. When mounting the handle, ensure fastenings do not protrude beyond the back surface of the Drawer Front.
I N T E G R A T E D P R O D U C T O N L Y Use of a depth gauge is recommended when drilling out holes for Drawer Front Mounting Panel. WARNING Page DS_14 4.1.5 Drawer Front Mounting Bracket Nut Holes Using a 11 / 32 (8.5mm) diameter drill bit, drill out the four screw holes in each door panel to a depth of 9 / 16 (14mm).
SECTION 5 STEP 5.1 CHANGING THE INTEGRATED BADGE ENCLOSURE INTEGRATED DRAWER FRONT INSTALLATION STEP 5.2 DISASSEMBLING THE INTEGRATED BADGE ASSEMBLY There are several different colored Integrated badges to choose from. They include black, chrome, satin & brass.
WARNING CAUTION Take care not to damage front surface of panel. Ensure all cuts are straight and care is taken to avoid damage to the Drawer Front. Care should be taken in the following steps. Overtightening will damage the Drawer Front. CAUTION I N T E G R A T E D P R O D U C T O N L Y STEP 5.
STEP 5.5 FITTING THE DRAWER FRONT TO THE DISHDRAWER Use a small amount of liquid soap along the lip of the seal to aid the Drawer Front to slide on easily against the seal.
SECTION 6 FINAL FITTING FOR SINGLE DISHDRAWER 6.1.1 Check final fit of DishDrawer in cavity. 6.1.2 Tighten M8 bolts. Page DS_18.
SECTION 12 FINAL CHECKS STEP 7.1 INSTALLATION WET TEST SECTION 7 STEP 7.2 TROUBLESHOOTING Water underneath DishDrawer, check the hose connections and hose for leaks. Water around water supply and drainage connections - check connections, existing plumbing and hoses for leaks.
デバイスFisher & Paykel DS602Iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Fisher & Paykel DS602Iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFisher & Paykel DS602Iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fisher & Paykel DS602Iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fisher & Paykel DS602Iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fisher & Paykel DS602Iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFisher & Paykel DS602Iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fisher & Paykel DS602Iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFisher & Paykel DS602Iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
