Fisher-Priceメーカー74420の使用説明書/サービス説明書
ページ先へ移動 of 44
Monster Sound BIGFOOT ® Owner ’ s Manual with Assembly Instructions Please read this manual and save it with your original sale’s receipt. For Model 74420 TM T ools needed for assembly: Phillips Screwdriver , Slotted Screwdriver , Hammer , Safety Scissors.
W ARNING • Children can be harmed by small par ts, sharp edges and sharp points in the vehicle’ s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, batteries or help in assembly of the vehicle.
CAUTION • Do not operate your vehicle for the first time until you have inserted the 30 amp fuses into the 6 volt batteries and charged the 6 volt batteries for at least 18 hours. Never charge the 6 volt batteries longer than 30 hours. • After first-time use, charge the 6 volt batteries for at least 14 hours after each use.
T able of Contents A Message to Parents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B Important Infor mation . . . . . . . . . . . . . . . . . . . . . .
Impor tant Infor mation • Carefully read this manual for important safety infor mation and operating instructions before using your vehicle. • Please complete and retur n the enclosed Registration Card, or call 1-800-348-0751 to register your vehicle by phone.
Seatbelt Set Pa r t s C Soundbox Cover Lens Guard – 2 Battery Retainer 6 If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751 , rather than return this product to the store. Please save all packaging material until assembly is complete to ensure that no parts are discar ded.
#8 x 1" Screw – 18 #6 x 1 1 / 2 " Screw – 2 30 Amp Fuse – 3* Knob Sport Bar Not Shown: Label Sheet 6 V olt Battery – 2 Steering Column 7 Pa r t s .354 Cap Nut – 3* All Shown Actual Size V ehicle Body Hood Seat Light Rack 12 V olt Charger 12-VOLT CHARGER T M * For your convenience, an extra 30 amp fuse and .
TM 8 Par ts Diagram D 1 Airscoop 2 Hood 3 Microphone 4 Steering Column 5 Steering Wheel 6 Steering Wheel Cap 7 Cap Nut 8 Sound Box Cover 9 Knob 10 Key 11 Seat 12 Lens Cover 13 Lens 14 Light Plate 15 L.
9 First-Time 6 V olt Batter y Charging E W ARNING • Batteries must be handled by adults only . • Never allow childr en to charge the 6 volt batteries. Batter y charging must be done by adults only . A child could be injur ed by the electricity involved in charging batteries.
® ® • Squeeze the Lock-In TM connector tabs on the charger connector and plug it into the battery connector . • Plug the charger into a standard 120 volt wall outlet. Note: If power flow to the wall outlet is controlled by a switch, make sure the switch is “ON”.
Assembly Do Not Omit Any Steps. Please set aside at least 45 minutes for assembly . • Locate the sound box battery compartment. • Loosen the screw in the battery compartment door with a Phillips screwdriver . The screw will remain in the door . • Lift the battery compartment door open.
• Insert the tabs on the sound box cover into the slots in the dash near the sound box. • Lower the bottom of the sound box cover . • Insert two #6 x 1 / 2 " screws through the sound box cover and into the dash. • T ighten the screws with a Phillips screwdriver .
• Fit the curved end of the steering column into the hole in the front axle. Please Note: Y ou may need to straighten the vehicle tires and rotate the steering column to fit it into the hole in the front axle.
Assembly • Hold the steering column in place and gently lower the vehicle body. • Position the steering wheel so that the spokes for m a “Y” as shown. • While supporting the steering column, fit the steering wheel onto the steering column. • Fit a cap nut onto the end of the steering column.
Assembly 15 12 Please Note: The seat can be assembled in either of two positions for your child’s comfort. • Push down on the center of the seat and slide it toward the rear of the vehicle. • Align the screw holes in the back of the seat with the first or second set of holes in the vehicle body.
14 Assembly • With the light plate at an angle, fit the notches in the light plate around the top tabs on the inside of a light housing. • Lower the light plate into the housing so that it lays flat. • Insert a #6 x 1 / 2 " screw into the light plate as shown.
Assembly 16 • Insert the wide tab on a lens assembly into the wide slot in a light housing assembly. • Press fir mly to snap the lens assembly into the light housing assembly. • Repeat this procedure to assem- ble the other lens assembly to the other light housing assembly.
Assembly 18 • Slide the assembled sport bar lights onto the light rack with the lenses facing away from the hinge. • Fit a 3 / 16 " washer onto each of two #8 x 1" screws. • Insert the #8 x 1" screws with washers up through the light rack and into the sport bar lights as shown.
Assembly 19 • Fit the ends of the sport bar into the holes in the vehicle body. 21 TM 20 • Fit the bottom half of the light rack onto the center section of the sport bar . • Insert two #6 x 1 1 / 2 " screws up through the bottom half of the light bar and into the sport bar , as shown.
TM • Fit a sport bar support into the hole in each sport bar foot. 23 Assembly • Using safety scissors, remove the sport bar brackets from the plastic connector . Dispose of the plastic connector . • Position the right sport bar bracket above the right side of the sport bar , as shown.
• Fold the sport bar bracket over the sport bar to close it around the sport bar and sport bar support. • Insert a #8 x 1" screw through the sport bar bracket and into the inside sur face of the sport bar , as shown. • T ighten the screw with a Phillips screwdriver .
Assembly • Position the tailgate with the flat side facing up. • Fit the peg on one side of the tailgate into the tailgate opening in the rear of the vehicle body. • Slide the peg on the other side of the tailgate into the tailgate opening in the other side of the vehicle body.
Assembly 30 T abs Ta b Left Headlight Lens • Using safety scissors, remove the headlight lenses from the plastic connector . Dispose of the plastic connector . • Align the tabs on the back of the right and left headlight lenses with the slots in the grille.
Assembly TM 33 Please Note: If you have already charged your Power Wheels ® Type H 6 volt batteries for at least 18 hours, you may want to install them in the battery compartment before assem- bling the hood. Please refer to the 6 V olt Battery Installation section on page 26 for instructions.
Assembly TM TM One-time assembly is now complete. IMPORT ANT NOTES: • Please carefully read the owner’s infor mation in this manual and teach your child about proper vehicle operation and rules for safe driving before allowing him to drive this vehicle.
• The battery compartment is locat- ed under the hood of your vehi- cle. • Place both Power Wheels ® Type H 6 volt batteries upright in the bat- tery compartment. Make sure the bottoms of the 6 volt batteries are flat on the bottom of the battery compartment and that the battery connectors extend toward the rear of the vehicle.
6 V olt Batter y Installation • Re-assemble the hood to the vehicle if you have removed it to install your Power Wheels Type H 6 volt batteries. • Lower the hood. • Face the front of the vehicle. • Using a slotted screwdriver , rotate the lock-fasteners in the hood so that they are horizontal () .
Charging the 6 V olt Batteries H W ARNING • Batteries must be handled by adults only . • Never allow childr en to charge the 6 volt batteries. Batter y charging must be done by adults only . A child could be injured by the electricity involved in char ging batteries.
2 • Squeeze the tabs on the motor harness connector to unplug it from the battery connector . • Squeeze the tabs on the charger connector to plug it into the battery connector . • Plug the charger into a standard 120 volt wall outlet . Note: If power to the outlet is con- trolled by a wall switch, make sure the switch is “ON”.
Batter y Handling/Care/Disposal I W ARNING • Batteries must be handled by adults only . • Never permit a child to handle batteries. The 6 volt batteries ar e heavy and contain sulfuric acid (electr olyte), and if dropped could result in serious injury .
• Adult supervision is r equired. Childr en do not have the judgement necessary to avoid many accidents. Be sure that children operating this vehicle can do so safely and that they are supervised at all times. • Never use near steps, driveways, steep inclines, roadways, alleys, swimming pool areas or other bodies of water .
Rules for Safe Driving 10° Incline should never be more than 10° • While driving across a steep slope, the vehicle may tilt and tip over . The wheels could lose traction, causing the vehicle to slip. •While driving up a steep incline, the motor may stop and the vehicle could roll backwards at an unsafe speed.
How to Operate Y our V ehicle K Beginner Drivers: Low Speed Forward T o Drive • Make sure the shifter is in the LOW ( ) position . • Press down on the foot pedal .
How to Operate Y our V ehicle T o Drive: Note: T o prevent damage to the motors, stop the vehicle before shifting speeds. • Make sure the shifter is in the HIGH ( ) position . • Press down on the foot pedal . The vehicle goes forward at a maximum of 5 mph .
? Frequently Asked Questions L Q. How often do I need to charge the 6 volt batteries? A. Charge the 6 volt batteries for a minimum of 14 hours after each use of the vehicle or whenever the vehicle begins to slow down. When the vehicle is not in regular use, charge the 6 volt batteries at least once a month until nor mal use is resumed.
Problems and Solutions Guide M Problem Possible Cause Solution V ehicle does not run Undercharged batteries Charge the batteries. New batteries should have been charged for at least 18 hours before using the vehicle for the first time. After first-time use, recharge batteries for at least 14 hours after each use.
V ehicle was running but Loose wire or loose connectors Check all wir es and connectors. Make sure the battery suddenly stopped connector is tightly plugged into the motor harness connector , and that there are no loose wir es around the motors.
Problem Possible Cause Solution V ehicle runs sluggishly Undercharged batteries Charge the batteries. New batteries should have been charged for at least 18 hours before using the vehicle for the first time. After first-time use, recharge batteries for at least 14 hours after each use.
Sometimes the vehicle doesn’t Loose wire or connector Check all wires ar ound the motors and all connectors to run, but other times it does make sure they ar e tight. Motor or electrical switch damage Contact your local Power Wheels ® Authorized Service Center for diagnosis and repair .
Statement of Limited W arranty N 90-day limited warranty for the Power Wheels ® Ride-On T oy V ehicle A 6-month battery warranty applying only to those 6 volt batteries which wer e included by Power Wheels ® , with the Power Wheels ® vehicle when originally pur chased.
Authorized Ser vice Centers 41 ALAB AMA BIRMINGHAM - F r igid Service & Sales, 701 Gra ymont Ave . Nor th, 35203, (205) 323-5831 BIRMINGHAM - F r igid Service & Sales, 1861 Centerpoint Rd., 35215, (205) 853-3952 BIRMINGHAM (HOMEWOOD) - D & R Appliance Company , 154 W est V alley Av e.
Authorized Ser vice Centers 42 ALAB AMA BIRMINGHAM - F r igid Service & Sales, 701 Gra ymont Ave . Nor th, 35203, (205) 323-5831 BIRMINGHAM - F r igid Service & Sales, 1861 Centerpoint Rd., 35215, (205) 853-3952 BIRMINGHAM (HOMEWOOD) - D & R Appliance Company , 154 W est V alley Av e.
Authorized Ser vice Centers 43 ALAB AMA BIRMINGHAM - F r igid Service & Sales, 701 Gra ymont Ave . Nor th, 35203, (205) 323-5831 BIRMINGHAM - F r igid Service & Sales, 1861 Centerpoint Rd., 35215, (205) 853-3952 BIRMINGHAM (HOMEWOOD) - D & R Appliance Company , 154 W est V alley Av e.
TM Monster Sound BIGFOOT ® FOR MODEL 74420 Questions? Please call Consumer Affairs toll-free at 1-800-348-0751. The trademark BIGFOOT is licensed from BIGFOOT 4 x 4, Inc. St. Louis, Missouri, U.S.A. Firestone is a registered trademark of Bridgestone/Firestone, Inc.
デバイスFisher-Price 74420の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Fisher-Price 74420をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFisher-Price 74420の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fisher-Price 74420の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fisher-Price 74420で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fisher-Price 74420を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFisher-Price 74420の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fisher-Price 74420に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFisher-Price 74420デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
