Follettメーカー110 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 28
Installation, Oper ation and Ser vice Manual F ollo wing installation, please f orw ard this man ual t o the appropr iat e operations per son. 00 1 09520R03 C/E1 1 0CT40 0A/W C/E1 1 0CR40 0A/W C/E1 1 0FB40 0A/W Order parts online www .follet tice.com 80 1 Church Lane • East on, P A 1 8040, US A (61 0) 252-730 1 • F ax (61 0) 250-0696 • www .
Befor e y ou begin Specif ications Field wir ing Installation Installing fr eestanding dispensers Installing count er t op dispensers Installing Sat ellite-f ill ™ icemaker s Installing t op mount i.
W elcome t o F ollet t F ollet t equipment enjo ys a well-deserved r eputation f or e x cellent perf or mance, long-t er m reliability and outstanding af ter -the-sale suppor t.
Specif ications Electrical 1 . Models with Sat ellite-f ill icemaker s (C/E1 1 0CR400A/W) Icemaker Dispenser 220V/60Hz/1 phase 5 amps 1 .5 amps 230V/50Hz/1 phase 5 amps 1 .5 amps 2. F reestanding models and models with int egral icemak ers (C/E1 1 0FB400A/W , C/E1 1 0CT400A/W) T otal sy stem 220V/60Hz/1 phase 6.
5 F ield wiring f or counter t op dispensers with Sat ellite-f ill icemaker s Model Electrical connection Current C1 1 0FB400A/W cord pro vided 220V 60Hz, 6.5 amp E1 1 0FB400A/W 230V 50Hz, 6.5 amp C1 1 0CT400A/W cord pr ovided 220V 60Hz, 6.5 amp E1 1 0CT400A/W 230V 50Hz, 6.
Installation pr ocedur es Installing fr eestanding dispensers 1 . C arefull y tip dispenser back t o e xpose underside and b lock up in place . 2. Remov e legs from shipping bo x (taped to dr ain pan of dispenser) and scre w into dispenser bot tom, taking car e t o seat legs securel y against under side of dispenser .
1 2. V er ify that water sensor t abs are immer sed in wat er in reservoir . 1 3. Remo ve t op front cov er by r emoving two scre ws at bot tom corners of co ver . Lif t cov er slightly and pull f orward. 1 4. If dispenser is equipped with SensorSAFE, r emove pr otecti v e plastic coating from dispense sensor labels .
Installing countertop dispenser s 1 . P osition dispenser in desired location, mark dispenser outline on counter and r emov e dispenser . 2. Dr ill f our 5mm (3/8") holes in counter (F ig.
1 0. Apply a thic k bead, appro ximatel y . 6mm (1/4") diameter , of NSF listed silicone sealant (Do w- Corning RTV -732 or equiv alent) 6mm (1/4") inside marked outline of dispenser .
Installing Satellit e-f ill icemak ers Models C/E1 1 0CR400A/W 1 . Install Satellit e-fill icemak er f ollowing instructions in icemaker man ual. 2. Run uninsulated ice tr anspor t tube from dispenser thr ough ice transpor t tube knock-out, (F ig. 5G) or through count er opening to icemak er .
1 . Remo ve dispenser t op front cov er by r emoving two scre ws at bot tom corners of co ver , lif ting cov er slightl y and pulling f orwar d. 2. Remov e icemaker compar tment top and side panels. 3. Remov e icemaker hold-down brac ket from fr ont of icemaker compartment.
User inf or mation How the dispenser w orks F ollet t’ s 1 1 0 ser ies automatic load ice and wat er dispensers recei ve ice fr om Follet t’ s 1 81kg (400 lb)/da y icemaker located in the dispenser base, in the cabinet t op or in a remot e location up to 6m (20 f t) aw ay .
Recommended w eekly cleaning 1 . W ash drain pan and grille with Solution A abov e. Rinse thoroughl y . 2. Slowly pour solution of one cup (237ml/8 oz) household b leach mix ed with 3.8L (1 gallon) hot w ater int o drain pan t o help pre vent alg ae gro wth in drain lines.
WTR S 1 7 M RELA Y #1 4 B RL Y A MAIN POWER SWITCH BIN SIGNAL T- S TAT SWITCH (220/230 V AC) ICE MACHINE POWER RED RD RD ORANGE RED PUR ORANGE WHITE WHITE WHITE WHITE WHITE WHITE WHITE WHITE 3 2 1 TIM.
How unit w orks — SensorS AFE models SensorSAFE models pr ovide “t ouchless” ice and water dispensing . When a container is placed within the actuation zone belo w the ice or wat er chute on SensorS AFE dispenser models, an infr a-red signal r eflects of f the container and is detect ed by the sensor .
Sym p to m 1 . Does not dispense ice 2. Does not dispense wate r 3. W ater runs continuousl y 4. Dispense wheel rot ates continuousl y 5. Icemaker runs continuousl y 6. Ice dispenses by itself Solution a. Replace dispense g ate b . Replace dispense solenoid c.
T r oubleshooting SensorS AFE boar d and sensor s Board guide LEDs, when illuminat ed, indicate the f ollowing: PWR (board po wer) CLN (cleaning, no dispensing c ycle) ICE (ice dispensing activ ated) .
18 Lens/sensor troub leshooting 1 . T ur n dispenser power s witch of f . 2. Remov e splash panel. 3. Disconnect wires fr om output terminal(s) (WTR, SOL, WM) on boar d. 4. Gently r emov e appropriate sensor/mounting b lock assemb l y from panel b y moving b lock side wa y s until edge of bloc k clears r etaining tab of panel.
Ice tr anspor t tube r eplacement Models C/E1 1 0FB400A/W , C/E1 1 0CR400A/W 1 . Remov e top and r ear access panel from dispenser (lo wer fr ont panel in fr eestanding unit). 2. Disconnect existing ice tube fr om engaging pin on tr anspor t tube brack et in ice stor age bin ev aporator and pull do wn through dispenser chase.
engaging pin 5mm (3/16") ice tube hole ice hose mounting brac ket ice le vel control stat ice tube 26mm (1") capillar y tube 20 All units 9. Slip supplied hose clamp onto tube and push tube onto e xit por t of e vapor ator . Do not t wist hose when securing t o evapor ator .
well nu t ice lev el control stat rubber grommet control box assemb ly ice mounting hose brack et knurled screw hopper assembly ice lev el control stat bin thermostat control box assemb ly Thermostat .
22 P ar t # Description Ref erence 502756 Co ver , top fr ont, 1 1 0 counter top (CT) 1 502703 Co ver , top fr ont, 1 1 0 counter top unit with S atellit e-fill icemak er (CR) & freest anding (FB).
P ar t # Description Ref erence 502057 F astener , dispense chute brac ket 1 502356 T ube, wat er station 2 502681 Co ver , dispense chute 3 50 1 829 Switch, dispense , ice, le ver actuat ed (includes.
24 P ar t # Description Ref erence 502057 F astener , dispense chute brac ket 1 502681 Co ver , dispense chute (includes labels) 2 502248 Chute and funnel, ice 3 502249 Chute , wat er 4 502247 Brac ke.
1 2 4 3 3 5 Wheel mot or and driv e s y stem 25 1 6 7 8 7 P ar t # Description Ref erence 50 1 699 Wheel mot or , 220V , 60Hz/230V , 50Hz 1 50 1 026 W asher , thrust 2 50 1 607 F an blade, wheel mot o.
26 P ar t # Description Ref erence 50 1 802 Baff le, ice 1 50 1 493 Wheel, dispense (includes driv e bar , rot ating agitator , threaded bar & r od) 2 50 1 494 Agitat or , rotating 3 50271 2 Brack.
27 P ar t # Description Refer ence 502598 Coil, chilled wat er (includes t wo 502599) 1 502599 Fit ting, w ater coil 2 502600 Brack ets, chilled wat er canister , pair (includes scr ews) 3 50260 1 Can.
Solenoid dispense assembl y P ar t # Description Ref erence # 50 1 844 Solenoid, dispense , 220V , 60 Hz/230V , 50Hz 1 502040 Cot ter pin 2 502039 Link age, solenoid (includes 502054 g rommet) 3 50204.
デバイスFollett 110 Seriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Follett 110 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFollett 110 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Follett 110 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Follett 110 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Follett 110 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFollett 110 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Follett 110 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFollett 110 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。