FordメーカーF-150 (2013)の使用説明書/サービス説明書
ページ先へ移動 of 592
DL3J 19A321 AA | February 2013 | Third P rinting | Owner’s Manual | F-150 | Litho in U.S.A. 2013 F- 150 Owner ’ s Manual for downer . com for d. ca 2013 F -150 Owner’s Manual I n f o r m a t i o.
Introduction 9 Child Safety 18 Child seats ........................................... 2 0 Child seat positioning ................................... 2 0 Booster seats ......................................... 2 2 Installing child safety seats .......
MyKey 71 Settings, MyKey ....................................... 7 1 Creating ............................................. 7 2 C l e a r i n g ............................................. 7 3 System status ......................................... 7 4 Remote start, MyKey .
Windows and Mirrors 98 Power windows ....................................... 9 8 E x t e r i o rm i r r o r s ...................................... 1 0 0 Interior mirrors ...................................... 1 0 4 Sun visors .......................
Seats 163 Sitting in the correct position ............................ 1 6 3 Head restraints ....................................... 1 6 4 Manual seats ........................................ 1 6 8 Power seats ........................................
Brakes 234 Brakes ............................................. 2 3 4 Hints on driving with anti-lock brakes ...................... 2 3 5 Parking brake ........................................ 2 3 5 T raction Control 236 T r a c t i o nC o n t r o l ™ .
Roadside Emergencies 294 Getting roadside assistance .............................. 2 9 4 Hazard warning flashers ................................ 2 9 6 Fuel cut-off switch .................................... 2 9 6 Jump-starting the vehicle .........
V ehicle Care 350 Cleaning products ..................................... 3 5 0 Cleaning the exterior .................................. 3 5 0 W a x i n g ............................................. 3 5 2 Repairing minor paint damage ...............
SYNC® 435 Pairing your phone for the first time ....................... 4 4 1 911 Assist™ ......................................... 4 5 5 V ehicle Health Report .................................. 4 5 8 MyFord T ouch® (If Equipped) 484 Privacy Information .
ABOUT THIS MANUAL Thank you for choosing Ford. W e recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it.
SYMBOL GLOSSAR Y W ARNING: Y ou risk death or serious injury to yourself and others if you do not follow the instruction highlighted by the warning symbol.
Symbol Description Symbol Description Symbol Description Fuel pump reset Fuse compartment Hazard warning flasher Heated rear window Interior luggage compartment release Jack Lighting control Low tire .
DA T A RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems.
Note: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data or information (e.g., name, gender , age, and crash location) is recorded (see limitations regarding 911 Assist and T raffic, Directions and Information privacy below).
Additionally , when you connect to T raf fic, Directions and Information (if equipped, U.S. only), the service uses GPS technology and advanced vehicle sensors to collect the vehicle’ s current loca.
REPLACEMENT P ARTS RECOMMENDA TION Y our vehicle has been built to the highest standards using quality parts. W e recommend that you demand the use of genuine Ford and Motorcraft parts whenever your vehicle requires scheduled maintenance or repair .
Special Instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. W ARNING: Please read the Supplementary Restraints System chapter . Failure to follow the specific warnings and instructions could result in personal injury .
MOBILE COMMUNICA TIONS EQUIPMENT Using mobile communications equipment is becoming increasingly important in the conduct of business and personal affairs.
GENERAL INFORMA TION See the following sections for directions on how to properly use safety restraints for children. W ARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your vehicle.
Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Small children Children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 ft. 9 in.
CHILD SEA TS Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat) for infants, toddlers or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). CHILD SEA T POSITIONING W ARNING: Airbags can kill or injure a child in a child seat.
W ARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a crash. W ARNING: Always restrain an unoccupied child seat or booster seat. These objects may become projectiles in a crash or sudden stop, which may increase the risk of serious injury .
Note: The child seat must rest tightly against the vehicle seat upon which it is installed. It may be necessary to lift or remove the head restraint. See the Seats chapter for information on head restraints.
T ypes of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child’ s head (as measured at the tops of the ears) above the top of the seat.
Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
INST ALLING CHILD SEA TS Using Lap and Shoulder Belts W ARNING: Airbags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Perform the following steps when installing the child seat with combination lap and shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in a seat with a combination lap and shoulder belt.
4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
This is necessary to remove the remaining slack that will exist once the extra weight of the child is added to the child restraint. It also helps to achieve the proper snugness of the child seat to your vehicle. Sometimes, a slight lean toward the buckle will additionally help to remove remaining slack from the belt.
The belt webbing below the tongue is the lap portion of the combination lap and shoulder belt, and the belt webbing above the tongue is the shoulder belt portion of the combination lap and shoulder belt. 1. Position the child safety seat in the center front seat.
4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
9. Check from time to time to be sure that there is no slack in the lap and shoulder belt. The shoulder belt must be snug to keep the lap belt tight during a collision. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician to make certain the child restraint is properly installed.
Y our vehicle is equipped with LA TCH lower anchors for child seat installation at the following seating positions (LA TCH is not available on F150 Regular cab) : • F150 SuperCab and SuperCrew The lower LA TCH anchors are located at the rear section of the rear seat between the cushion and seatback.
Use of Inboard Lower Anchors from the Outboard Seating Positions (Center Seating Use) W ARNING: The standardized spacing for LA TCH lower anchors is 280 mm (11 inches) center to center .
The passenger seats of your vehicle are equipped with built-in tether strap anchors located behind the seats as described below . The tether anchors in your vehicle may be loops of webbing above the seat back or an anchor bracket behind the seat on the rear edge of the seat cushion.
Front Seat T ether Strap Attachment (Regular Cab) 1. Route the child safety seat tether strap over the back of the seat and under the head restraint. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seat back.
Rear Seat T ether Strap Attachment (SuperCab and SuperCrew) There are three loops of webbing just above the back of the rear seat (along the bottom edge of the rear window). These loops are to be used as both routing loops and anchor loops for up to three child safety seat tether straps.
• Always put the tether strap through the routing loop. The head restraint support post will hold the child seat tightly , but the head restraint post is not strong enough to hold the child seat during a collision. 3. T ighten the tether strap according to the child seat manufacturer’ s instructions.
PRINCIPLES OF OPERA TION W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a crash. W ARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
W ARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death. W ARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child.
F ASTENING THE SAFETY BEL TS The front outboard and rear safety restraints in your vehicle are combination lap and shoulder belts. 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch.
Before you can reach and latch a lap and shoulder belt having a cinch tongue into the buckle, you may have to lengthen the lap belt portion of it. 1. T o lengthen the lap belt, pull some webbing out of the shoulder belt retractor .
Restraint of Pregnant Women W ARNING: Always ride and drive with your seat back upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. The shoulder portion of the safety belt should be positioned across the chest.
All safety restraints in the vehicle are combination lap and shoulder belts. The driver safety belt has the first type of locking mode, and the front outboard passenger and rear seat safety belts have.
How to Disengage the Automatic Locking Mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Safety Belt Extension Assembly W ARNING: Do not use extensions to change the fit of the shoulder belt across the torso.
SAFETY BEL T W ARNING LIGHT AND INDICA TOR CHIME This lamp illuminates and an audible warning will sound if the driver’ s safety belt has not been fastened when the vehicle’ s ignition is turned on. Conditions of Operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the on position.
If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder feature will not activate.
Deactivating and Activating the Belt-Minder® Feature W ARNING: While the design allows you to deactivate your Belt-Minder , this system is designed to improve your chances of being safely belted and surviving an accident. W e recommend you leave the Belt-Minder system activated for yourself and others who may use the vehicle.
CHILD RESTRAINT AND SAFETY BEL T MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodically to make sure they work properly and are not damaged. Inspect the vehicle and child seat safety belts to make sure there are no nicks, tears or cuts.
PERSONAL SAFETY SYSTEM™ The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries.
PRINCIPLES OF OPERA TION W ARNING: Airbags do not inflate slowly or gently , and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module.
The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag.
DRIVER AND P ASSENGER AIRBAGS W ARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury .
Proper Driver and Front Passenger Seating Adjustment W ARNING: The National Highway T raffic Safety Administration recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant’ s chest and the driver airbag module.
If two adults and a child occupy a Regular Cab, properly restrain the child in the center front unless doing so would interfere with driving your vehicle. This provides lap and shoulder belt protection for all occupants, and airbag protection for the adults.
High-series vehicles (if equipped) The front passenger sensing system uses a passenger airbag status indicator which will illuminate indicating that the front passenger frontal airbag is either ON (enabled) or OFF (disabled). The indicator lamp is located by the radio.
• Restart your vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’ s frontal airbag. • If the passenger airbag status indicator OFF lamp remains lit even after this, the person should be advised to ride in the rear seat.
The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the previous list.
Low-series vehicles (if equipped) The front passenger sensing system uses a pass airbag off indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled.
• Restart your vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’ s frontal airbag. • If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat.
SIDE AIRBAGS W ARNING: Do not place objects or mount equipment on or near the airbag cover , on the side of the seat backs (of the front seats), or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.
The system consists of the following: • a tag on the seat back indicating that side airbags are found on your vehicle • side airbags located inside the seat back of the driver and front passenger seats. • crash sensors and monitoring system with readiness indicator .
W ARNING: All occupants of your vehicle including the driver should always wear their safety belts even when an airbag supplemental restraint system and curtain airbag is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.
Children 12 years old and under should always be properly restrained in the rear seats. The Safety Canopy will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening.
If any of these things happen, even intermittently , have the supplemental restraint system serviced at an authorized dealer immediately . Unless serviced, the system may not function properly in the event of a crash.
GENERAL INFORMA TION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditio.
REMOTE CONTROL Integrated Keyhead T ransmitters (IKT s) (If Equipped) Y our vehicle may be equipped with two integrated keyhead transmitters. Use the key blade to start your vehicle and unlock or lock the driver door from outside the vehicle. The transmitter portion functions as the remote control.
Integrated Keyhead Transmitter 1. T wist a thin coin in the slot near the key ring to remove the battery cover (1). 2. Carefully peel up the rubber gasket (2) from the transmitter if it does not come off with the battery cover . 3. Remove the old battery (3).
Deactivating Memory from the Transmitter 1. Press and hold the desired memory button for five seconds. A tone will sound after about two seconds. Continue to hold until a second tone is heard. 2. W ithin three seconds press the unlock button on the remote control.
The remote start system will not work if: • the ignition is on • the alarm system is triggered • you disable the feature • the hood is not closed • the transmission is not in P • the vehicle battery voltage is too low • your service engine soon light is on.
Extending the V ehicle Run Time Repeat Steps 1 and 2 with your vehicle still running to extend the run time for another remote start duration. If the duration is set to last 10 minutes, the duration will extend by another 10 minutes beginning after what is left of the first activation time.
PRINCIPLES OF OPERA TION MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as administrator keys or admin keys.
• V ehicle speed minders of 45, 55 or 65 mph (75, 90 or 105 km/h). Once you select a speed, it will be shown in the display , followed by an audible tone when the preselected vehicle speed is exceeded. • Audio system maximum volume of 45%. A message will be shown in the display when you attempt to exceed the limited volume.
Programming/Changing Optional Settings Use the information display to access your configurable MyKey settings. For T ype 1 information display settings 1. Switch the ignition on using an admin key . 2. Press SETUP until RESET FOR MYKEY SETTINGS is displayed.
For T ype 2 information display settings: 1. Access main menu of your information display and select Settings , then MyKey . 2. Scroll to Clear All and press the OK button.
MYKEY TROUBLESHOOTING Condition Potential causes I cannot create a MyKey . • The key or fob used to start the vehicle does not have admin privileges. • The key or fob used to start the vehicle is the only admin key (there always has to be at least one admin key).
LOCKING AND UNLOCKING Y ou can use the power door lock control or the remote control to lock and unlock the vehicle. Power Door Locks (If Equipped) The power door lock control is located on the driver and front passenger door panels. A. Unlock B. Lock Remote Control Y ou can use the remote control anytime the vehicle is not running.
Smart Unlocks (If Equipped) This feature helps to prevent you from locking yourself out of your vehicle if your key is still in the ignition. When you open the driver door and lock your vehicle with the power door lock control, all the doors will lock then unlock if your key is still in the ignition.
Autolock: Once in programming mode, press the power door unlock button then the lock button. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. Autounlock: Once in programming mode, press the power door lock button then the unlock button.
SECURICODE™ KEYLESS ENTR Y KEYP AD (IF EQUIPPED) Y ou can use the keyless entry keypad to lock or unlock the doors without using a key . The keypad can be operated with the factory-set 5-digit entry code; this code is located on the owner’ s wallet card in the glove box and is available from your authorized dealer .
Programming Memory to a Personal Entry Code T o program a personal entry code to recall memory settings, repeat Steps 1–4 above. • Pressing 1 • 2 on the keypad in Step 4 will program the code to driver memory setting 1. • Pressing 3 • 4 in Step 4 will program the code to driver memory setting 2.
Unlocking and Locking the Doors T o unlock the driver door: Enter the factory-set 5-digit code or your personal code. Y ou must press each number within five seconds of each other . The interior lamps will illuminate. Note: All doors will unlock if the two-stage unlocking feature is disabled.
SECURILOCK® P ASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Programming a Spare Key Note: A maximum of eight coded keys can be programmed to your vehicle. Only four of these eight can be integrated keyhead transmitters. Y ou can program your own integrated keyhead transmitters or standard SecuriLock coded keys to your vehicle.
ANTI-THEFT ALARM (IF EQUIPPED) The system will warn you of unauthorized entry to your vehicle. The turn signal lamps will flash and the horn will sound when: • any door or the hood is opened without using the key or the remote control • the ignition is turned on with an invalid key .
ADJUSTING THE STEERING WHEEL W ARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. Refer to Sitting in the Correct Position in the Seats chapter . 1. Unlock the steering column.
Power Tilt and T elescope Steering Column (If Equipped) W ARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. Refer to Sitting in the Correct Position in the Seats chapter .
AUDIO CONTROL (IF EQUIPPED) T ype 1 A. V olume up B. Seek up or next C. Media D. Seek down or previous E. V olume down T ype 2 A. V olume up B. Seek up or next C. Media D. Seek down or previous E. V olume down Media Press the media button repeatedly to scroll through available audio modes.
VOICE CONTROL (IF EQUIPPED) A. V oice recognition B. Phone mode C. Confirm selection See the SYNC or MyFord T ouch chapter . CRUISE CONTROL (IF EQUIPPED) See the Cruise Control chapter .
INFORMA TION DISPLA Y CONTROL T ype 1 T ype 2 See the Information Displays chapter . SETUP RESET INFO SET RESET INFO SETUP ON OFF RSM CNCL OK Steering Wheel 89 2013 F-150 (f12) Owners Guide gf, 3rd Pr.
ADJUST ABLE PEDALS (IF EQUIPPED) W ARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. The control is located on the left side of the steering column. Press and hold the appropriate control to move the pedals.
WINDSHIELD WIPERS Note: Fully defrost the windshield in icy conditions before turning on the windshield wipers. Rotate the end of the control away from you to increase the speed of the wipers.
WINDSHIELD W ASHERS Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washer before wiping a dry windshield. Note: Do not operate the washer when the washer reservoir is empty .
LIGHTING CONTROL • Rotate the headlamp control clockwise to the first position to turn on the parking lamps. • Rotate clockwise to the second position to also turn on the headlamps. High Beams Pull the lever fully past the detent to switch the high beams on.
AUTOLAMPS (IF EQUIPPED) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for a predetermined amount of time after the ignition switch is turned to off.
DA YTIME RUNNING LAMPS (IF EQUIPPED) W ARNING: Always remember to switch your headlamps on in low light situations or during inclement weather . The system does not activate the tail lamps and may not provide adequate lighting during these conditions.
Lane Change T o indicate a left or right lane change: • Push the lever up/down to the first stop position and release. The turn signals will flash three times and stop. • Push the lever up/down to the first stop position and hold. The turn signals will flash for as long as the lever is held in this position.
Rear Dome, Courtesy Lamps (If Equipped) The dome lamp lights when: • any door is opened. • the instrument panel dimmer button is pressed until the courtesy lamp comes on. • any of the remote entry controls are pressed and the ignition is off. The reading portion, the two outer lights, can only be turned on and off at the lamp.
POWER WINDOWS (IF EQUIPPED) W ARNING: Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves. W ARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the proximity of the window openings.
Restoring the One-T ouch Up Functionality Note: Perform one-touch up re-calibration with the door closed. Calibrating with the door open will cause the window to continuously bounce back. Functionality may be lost under low battery power conditions. T o reset this function after restoring full battery power: 1.
Power Sliding Back Window (If Equipped) W ARNING: When operating the power sliding back window you must ensure all rear seat occupants and/or cargo are not in the proximity of the back window . W ARNING: Do not leave children unattended in the vehicle and do not let children play with the power sliding back window .
T o adjust your mirrors: 1. Select the mirror you want to adjust. 2. Move the control in the direction you want to tilt the mirror . 3. Return the control to the center position to lock mirrors in place. Fold-Away Exterior Mirrors Push the mirror toward the door window glass.
Auto-Dimming Feature (If Equipped) The driver’ s side exterior mirror will automatically dim when the interior auto-dimming mirror is activated. Signal Indicator Mirrors (If Equipped) The rear -facing portion of the appropriate mirror housing will blink when the turn signal is activated.
Integrated Blind Spot Mirror (If Equipped) W ARNING: Objects in the blind spot mirror are closer than they appear . Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They are designed to assist you by increasing visibility along the side of your vehicle.
INTERIOR MIRROR W ARNING: Do not adjust the mirror when your vehicle is moving. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia based cleaning products. Y ou can adjust the interior mirror to your preference.
MOONROOF (IF EQUIPPED) W ARNING: Do not let children play with the moonroof or leave children unattended in the vehicle. They may seriously hurt themselves. W ARNING: When closing the moonroof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moonroof opening.
GAUGES Cluster shown in standard measure. Metric similar . A. Engine oil pressure gauge B. Engine coolant temperature gauge C. Fuel gauge D. T ransmission fluid temperature gauge E. Speedometer F . Information display . See Information displays for more information.
Engine Coolant T emperature Gauge Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.
W ARNING LAMPS AND INDICA TORS The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information.
Charging System It will illuminate when the 12–volt battery is not charging properly . Contact your authorized dealer as soon as possible. This indicates a problem with the electrical system or a related component. Check 4X4 Displays with the message CHECK 4X4 when a four -wheel drive fault is present.
Fasten Safety belt It will illuminate and a chime will sound to remind you to fasten your safety belt. High Beam It will illuminate when the headlamp high beam is switched on. It will flash when you use the headlamp flasher . Hill Descent (if equipped) Illuminates when hill descent is turned on.
Service Engine Soon The service engine soon indicator light illuminates when the ignition is first turned to the on position to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing.
4X2 Illuminates momentarily when two-wheel drive high is selected. If the light fails to display when the ignition is turned on, or remains on, have the system serviced immediately by your authorized dealer . 4X4 LOW Illuminates when four -wheel drive low is engaged.
GENERAL INFORMA TION W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Y our primary responsibility is the safe operation of the vehicle.
Info Press the INFO button repeatedly to cycle through the following features: Note: Some options may appear slightly different or not at all if the items are optional.
System Check and V ehicle Feature Customization Press the SETUP button repeatedly to cycle the message center through the following features: SETUP RESET FOR SYSTEM CHECK press the RESET button XXX% OIL LIFE DOOR ST A TUS BRAKE SYSTEM FUEL LEVEL LOW TBC GAIN = XX.
SETUP LANGUAGE = ENGLISH / SP ANISH / FRENCH press the RESET button English / Spanish / French • RESET FOR SYSTEM CHECK: The message center will begin to cycle through the vehicle systems and provide a status of the item if needed. Some systems show a message only if a condition is present.
• REAR P ARK AID (if equipped): This feature sounds a tone to warn the driver of obstacles near the rear bumper , and functions only when R (Reverse) gear is selected. • TRAILER SW A Y (if equipped): This feature uses the electronic stability control to mitigate trailer sway .
• Fuel Economy • T ruck Apps (If Equipped) • Settings • Information Gauge Mode Use the arrow buttons to choose between the following gauge options. Gauge Mode Gauges Detail T rans T emp Compass The compass orientation can be changed between fixed north or rotating north.
Trip A/ B Use the arrow buttons to choose between the following trip options. T rip A/ B T rip time T rip distance Fuel used A vg mpg(L/100km) Odometer (displays in lower line and may display in other menus) Press OK to pause the T rip A or B screen/press again to un-pause.
Hold OK to Reset, this resets the currently displayed fuel economy information. • Instant MPG: shows instantaneous fuel usage. • mi to E: shows the approximate distance the vehicle can travel before running out of fuel. • A verage MPG: shows the average fuel usage based on time.
T ruck Apps T railer T railer disconnected. Disregard this status if your vehicle is not equipped with a factory installed trailer brake controller . This message may appear when an aftermarket TBC is used even when the trailer is connected.
T ruck Apps T railer Press OK for options Options Connection Checklist (if equipped) Conventional, Fifth Wheel and Gooseneck. Use the up/down arrows to highlight one of these choices and press OK to display the connection checklist. Follow the on-screen instructions to go through the connections list.
Settings In this mode, you can configure different driver setting choices. Note: Some items are optional and may not appear . Settings Driver Assist Rear Park Aid On/Off Rear Video Camera Camera Delay On/Off Visual Park Aid On/Off Guidelines Fixed/Off Zoom Levels (This will only be shown when Reverse (R) is selected.
Settings V ehicle Autolamp Delay Off or XXX seconds Compass Zone Setting (1–15) See the diagram below to determine your magnetic zone. Calibration (When choosing Calibration, follow the on-screen di.
Compass: Determine which magnetic zone you are in for your geographic location by referring to the zone map. Settings MyKey Create MyKey Hold OK to Create MyKey AdvanceT rac Always On / Selectable MAX.
Information In this mode, you can view different vehicle system information and perform a system check. Information MyKey Admin Keys (Number of admin keys) MyKeys (Number of MyKeys programmed) MyKey Miles (km) (Distance traveled using a programmed MyKey) System Check Some items will only display during a system check if a problem has been detected.
AdvanceT rac® / T raction Control Messages Action / Description SER VICE ADV ANCETRAC Displayed when the AdvanceT rac® system has detected a condition that requires service. Contact your authorized dealer as soon as possible. ADV ANCETRAC OFF Displayed when the AdvanceT rac® system has been disabled by the driver .
Battery and Charging System Messages Action / Description TURN POWER OFF TO SA VE BA TTER Y Displayed when the battery management system determines that the battery is at a low state of charge or , the ignition has been in accessory position or on position with the engine off for approximately 45 minutes.
Door Messages Action / Description X DOOR AJAR Displayed when the corresponding door is not completely closed. Drivetrain Messages Action / Description NEUTRAL TOW ENABLED LEA VE TRANSMISSION IN NEUTRAL Displayed when the transfer case is in the neutral position.
Engine Messages Action / Description POWER REDUCED TO LOWER ENGINE TEMP Displayed when the engine temperature gauge needle moves to H. Y ou may notice reduced engine power .
MyKey® Messages Action / Description MYKEY ACTIVE DRIVE SAFEL Y Displayed when MyKey® is active. ADV ANCETRAC AL W A YS ON - MYKEY SETTING Displayed when a MyKey® is in use and the ESC cannot be deactivated.
Off Road Messages Action / Description FOR OFF ROAD SLOW TO 5 MPH Displayed when the vehicle speed requirement for off-road mode entry has not been met. OFF ROAD MODE ENABLED Displayed when off-road mode becomes active. EXITING OFF ROAD MODE Displayed when off-road mode becomes inactive.
T ire Messages Action / Description LOW TIRE PRESSURE Displays when one or more tires on your vehicle have low tire pressure. TIRE PRESSURE MONITOR F AUL T Displays when the tire pressure monitoring system is malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer .
T railer Messages Action / Description TRAILER SW A Y REDUCE SPEED Displayed when the trailer sway control has detected trailer sway . WIRING F AUL T ON TRAILER Displayed if there are certain faults in the vehicle wiring and trailer wiring/brake system.
GENERAL INFORMA TION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.
MP3 T rack and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracks and folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 track mode (system default) and MP3 folder mode.
AM/FM W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
E. Memory presets: Store your favorite radio stations. T o store a radio station, tune to the station, then press and hold a preset button until sound returns. F. AM/FM: Press this button to select a frequency band. G. VOL-PUSH: • Press this button to switch the system off and on.
• Save presets automatically by using the autoset feature. Press MENU repeatedly until AUTO PRESET ON/OFF appears in the display . Use the SEEK buttons to turn AUTO PRESET to ON, and either wait five seconds for the search to initiate or press OK to immediately start the search.
• All Seat Mode/Driver Seat Mode optimizes sound quality for the chosen seating position. • DSP Mode (if equipped) allows you to choose between STEREO SURROUND mode and STEREO mode. J. SEEK: • In radio mode, select a frequency band and press one of these buttons.
Q. CA T/FOLD: • In SIRIUS mode, press this button to switch between turning the most recently selected satellite radio category off or on. • In MP3 mode, press this button, then use the SEEK buttons to access the previous or next folder . R. SCAN: • In radio mode, press this button to hear a brief sampling of all radio stations.
MyFord® SYSTEM W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
C. Memory presets: • In radio mode, store your favorite radio stations. T o store a radio station, tune to the station, then press and hold a preset button until sound returns.
K. SOUND: Press this button to adjust settings for T reble, Middle, Bass, Balance and Fade. L. MENU: Press this button to access different audio system features. See Menu structure later in this section. M. PHONE: Press this button to access the phone features of the SYNC system.
SIRIUS Scan Select for a brief sampling of all available channels. Show ESN Select to view your satellite radio electronic serial number (ESN). Y ou need this number when communicating with SIRIUS® to activate, modify or track your account. Channel Guide Select to view available satellite radio channels.
Audio Settings Spd. Comp. V ol. Automatically adjusts the volume to compensate for speed and wind noise. Y ou can set the system between 0 and +7. Sound Select to adjust settings for T reble, Middle, Bass, Fade and Balance. Occupancy Mode Select to optimize sound quality for the chosen seating position.
AM/FM/CD SONY AUDIO SYSTEM W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
F. Seek, Reverse and Fast Forward: • In radio mode, select a frequency band and press one of these buttons. The system stops at the first station it finds in that direction. • In SIRIUS mode, press these buttons to select the previous or next channel.
The auxiliary input jack allows you to connect and play music from your portable music player through your vehicle speakers. Y ou can use any portable music player designed for use with headphones. Y our audio extension cable must have male 1 ⁄ 8 -inch (3.
MEDIA HUB The media hub is located either in the center console or behind an access door in the instrument panel (below the climate control buttons) and has the following features: A. A/V inputs B. SD card slot C. USB ports For more information, see the MyFord T ouch or MyLincoln T ouch chapter .
Potential satellite radio reception issues Station overload When you pass a ground-based broadcast-repeating tower , a stronger signal may overtake a weaker one and the audio system may mute. Satellite radio signal interference Y our display may show ACQUIRIN G.
T roubleshooting Radio display Condition Possible action Acquiring Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly . Sat Fault/SIRIUS system failure There is an internal module or system failure present.
MANUAL HEA TING AND AIR CONDITIONING SYSTEM A. Defrost: Distributes air through the windshield defroster vents and demister vents. This setting can also be used to defog and clear the windshield of a thin covering of ice. B. Rear defrost and heated mirrors: T urns the heated windows and mirrors off and on.
D. A/C: Press to turn air conditioning off and on. Air conditioning cools the vehicle using outside air . T o improve air conditioning when starting your vehicle, drive with the windows slightly open for two to three minutes. E. Recirculated air: Press to switch between outside air and recirculated air .
MANUAL HEA TING AND AIR CONDITIONING SYSTEM A. Fan speed control: Controls the volume of air circulated in your vehicle. T urn to select the desired fan speed or switch off. If you switch the fan off, the windshield may fog up. B. Rear defrost: T urns the heated windows and mirrors off and on.
Distributes air through the instrument panel vents, floor vents, and demister vents. Distributes air through the floor vents. E. A/C: Press to turn air conditioning off and on.
DUAL AUTOMA TIC TEMPERA TURE CONTROL SYSTEM Note: Y ou can switch temperature units between Fahrenheit and Celsius. See Menu features in the MyFord T ouch or MyLincoln T ouch chapter . A. Power/Driver temperature control: Press to turn the climate control system off and on.
D. Air distribution control: Press to set the air distribution to a position listed below: Distributes air through the windshield defroster vents, demister vents and floor vents. Distributes air through the instrument panel vents. Distributes air through the instrument panel vents, floor vents, and demister vents.
I. Fan speed control +: Press to increase the volume of air circulated in your vehicle. J. AUTO: Press to turn on fully automatic operation. Select the desired temperature using the temperature control.
T o aid in side window defogging and demisting in cold or humid weather: 1. Select Floor/Panel. 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents toward the side windows.
HEA TED WINDOWS AND MIRRORS (IF EQUIPPED) Heated Rear Window Note: The ignition must be switched on to use this feature. Note: If your vehicle is equipped with a sliding rear window , the defroster does not operate when the window is opened. Press the button to clear the rear window of thin ice and fog.
Automatic Climate Systems Automatic Settings Y ou can set the climate control to operate in AUTO mode through the information display setting: Remote Start > Climate Control > Heater – A/C > Auto. The climate control system automatically sets the interior temperature to 72°F (22°C).
SITTING IN THE CORRECT POSITION W ARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash.
• Keep sufficient distance between yourself and the steering wheel. W e recommend a minimum of 10 inches (250 millimeters) between your breastbone and the airbag cover . • Hold the steering wheel with your arms slightly bent. • Bend your legs slightly so that you can press the pedals fully .
Front Seat Head Restraints Rear Seat Outboard Head Restraints Rear Seat Center Head Restraint The head restraints consist of : A. An energy absorbing head restraint B. T wo steel stems C. Guide sleeve adjust and release button D. Guide sleeve unlock and remove button E.
Adjusting the Head Restraint Raise: Pull up the head restraint. Lower: 1. Press and hold button C. 2. Push down on the head restraint. Remove: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Press and hold buttons C and D.
These head restraints consist of : A. An energy absorbing head restraint B. T wo steel stems C. Guide sleeve unlock and remove button Remove: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Press and hold buttons C. 3.
MANUAL SEA TS Moving the Seats Backward and Forward Recline Adjustment Manual Lumbar T urn the control to adjust your support. 168 Seats 2013 F-150 (f12) Owners Guide gf, 3rd Printing, February 2013 U.
POWER SEA TS (IF EQUIPPED) W ARNING: Before returning the seat back to its original position, make sure that cargo or any objects are not trapped behind the seat back. W ARNING: Never adjust the driver’ s seat or seat back when the vehicle is moving.
MEMOR Y FUNCTION (IF EQUIPPED) W ARNING: Before activating the seat memory , make sure that the area immediately surrounding the seat is clear of obstructions and that all occupants are clear of moving parts. W ARNING: Do not use the memory store function when your vehicle is moving.
Recalling Saved Memory Positions T o recall position 1 settings, press and release memory button 1. The memory features will move to the saved memory 1 position.
REAR SEA TS Folding Up the Rear Seats (SuperCab only) The rear seat has a split 60/40 cushion. Each seat cushion can be flipped up into a vertical storage position. 1. Pull the control to release the seat cushion. 2. Rotate the seat cushion up until it locks into the vertical storage position.
Folding Up the Rear Seats (SuperCrew V ehicles Only) The rear seat has a split 60/40 cushion. Each seat cushion can be flipped up into a vertical storage position. Rotate the seat cushion up by lifting on the corner until it locks into the vertical storage position.
Rear Heated Seats (If Equipped) W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
• Push the indicated side of the control for minimum heat. • Push again to deactivate. The heated seat module resets at every ignition run cycle. While the ignition is in the on position, activate the high or low heated seat switch to enable heating mode.
HEA TED SEA TS (IF EQUIPPED) W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
HEA TED AND COOLED SEA TS (IF EQUIPPED) Heated Seats W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
Heated and Cooled Seats Air Filter Replacement (If Equipped) The heated and cooled seat system includes air filters. They must be replaced periodically . See scheduled maintenance information. The filter is located under each front seat. Access the filter from the second row foot-well area.
FRONT SEA T ARMREST (IF EQUIPPED) Push the release control to move the armrest up or down. Pull out the drawer at the bottom of the center seat to access the cup holders (if equipped) T o gain access to the storage compartment (if equipped) under the center seat cushion, lift the latch to open the lid.
UNIVERSAL GARAGE DOOR OPENER The appearance of your vehicle’ s universal garage door opener will vary according to your option package. Before programing, make sure you identify which transmitter you have by comparing it to the graphics below .
Note: W e recommend that upon the sale or lease termination of your vehicle, you erase the programmed function buttons for security reasons. See Erasing the Function Button Codes later in this section. Note: Y ou can program a maximum of three devices.
Rolling Code Programming Note: If you do not follow the time-sensitive instructions, the device will time out and you will have to repeat the complete procedure. Note: It may be helpful to have another person assist you in programming the transmitter .
Fixed Code Programming Note: It may be helpful to have another person assist you in programming the transmitter . T o program units with fixed code DIP switches, you will need the garage door hand-held transmitter , paper and a pen or pencil. 1. Switch the ignition on.
6. Press and hold the function button you would like to use to control the garage door . Note: Y ou may need to hold the button from 5–55 seconds before observing movement of the garage door . 7. When the garage door moves, release the button within one second.
HOMELINK® WIRELESS CONTROL SYSTEM (IF EQUIPPED) W ARNING: Make sure that the garage door and security device are free from obstruction when you are programming.
Programming Note: Put a new battery in the hand-held transmitter . This will ensure quicker training and accurate transmission of the radio-frequency signal. 1. W ith your vehicle parked outside of the garage and your key in the ignition, turn the key so that the ignition is in the on position.
Note: Y ou may need a ladder to reach the unit and you may need to remove the cover or lamp lens on your garage door opener . 5. Press the learn button on the garage door opener motor , and then you have 30 seconds to complete the next step. 6. Return to your car .
Programing the transmitters T o program HomeLink to the transmitter you must first put the transmitter into programming mode. T o do this: A. Red LED B. Green LED 1. Press and hold one of the buttons on the hand-held transmitter for 10 seconds. The LED light will change from green to green and red.
Programming HomeLink to the Genie Intellicode garage door opener motor Note: Y ou may need a ladder to access the garage door opener motor . T o program HomeLink to the garage door opener motor: 1. Press and hold the PROGRAM button on the garage door opener motor until both blue LED’ s turn on.
AUXILIAR Y POWER POINTS W ARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty , and can result in fire or serious injury . Note: If used when the engine is not running, the battery will discharge.
1 10 V olt AC Power Point (If Equipped) W ARNING: Do not keep electrical devices plugged in the power point whenever the device is not in use. Do not use any extension cord with the 110 volt AC power point, since it will defeat the safety protection design.
The power point is not designed for the following electric appliances; they may not work properly: • Cathode-ray , tube-type televisions • Motor loads, such as vacuum cleaners, electric saws and other electric power tools, compressor -driven refrigerators, etc.
CENTER CONSOLE (IF EQUIPPED) Stow items in the cupholder carefully as items may become loose during hard braking, acceleration or collisions, including hot drinks which may spill.
GENERAL INFORMA TION W ARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. W ARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover .
IGNITION SWITCH A. Off: The ignition is off. Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery to lose charge. B. Accessory: Allows the electrical accessories such as the radio to operate while the engine is not running.
Note: If you cannot start the engine on the first try , wait for a short period and try again. If you have difficulty starting the engine when the temperature is below -13°F (-25°C), press the accelerator pedal slightly and try again.
Do not crank the engine for more than 10 seconds at a time as starter damage may occur . If the engine fails to start, turn the key to off and wait 30 seconds before trying again. Do not use starting fluid such as ether in the air intake system. Such fluid could cause immediate explosive damage to the engine and possible personal injury .
ENGINE BLOCK HEA TER (IF EQUIPPED) W ARNING: Failure to follow engine block heater instructions could result in property damage or physical injury . W ARNING: Do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters.
• Make sure the heater , heater cord and extension cord are firmly connected. • Check for heat anywhere in the electrical hookup once the system has been operating for approximately 30 minutes. • Make sure the system is unplugged and properly stowed before driving your vehicle.
SAFETY PRECAUTIONS W ARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. W ARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops.
• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin.
Choosing the Right Fuel With a Flex Fuel V ehicle (If Equipped) Note: If your vehicle is flex fuel capable, it will have a yellow bezel placed over the fuel fill inlet. Flex fuel vehicles are designed to use unleaded gasoline or an ethanol fuel blend that contain up to 85% ethanol.
RUNNING OUT OF FUEL A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine.
1. Locate the white plastic funnel. In SuperCab and Super Crew vehicles, it is located under the second row driver side seat near the spare tire tool box. On regular cab vehicles, the funnel is located behind the driver seat. 2. Slowly insert the funnel into the Easy Fuel® system.
Easy Fuel® “No Cap” Fuel System W ARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door , do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury .
FUEL CONSUMPTION Filling the T ank The advertised capacity is the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty . Empty reserve is the amount of fuel in the tank after the fuel gauge indicates empty .
EMISSION CONTROL SYSTEM W ARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. W ARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment.
Do not make any unauthorized changes to your vehicle or engine. By law , vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Readiness for Inspection/Maintenance (I/M) T esting Some state, provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.
AUTOMA TIC TRANSMISSION W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the off position and remove the key whenever you leave your vehicle.
D (Drive) with T ow/Haul On The T ow/Haul feature improves transmission operation when towing a trailer or a heavy load. All transmission gear ranges are available when using T ow/Haul.
3 (Third) (column-shift only) (For vehicles without SST) T ransmission operates in third gear only . Used for improved traction on slippery roads. 2 (Second) T ransmission operates in 2nd gear only . Use 2 (Second) to start-up on slippery roads. 1 (First) • T ransmission operates in 1st gear only .
M (Manual) Moving the gearshift lever from drive position D (Drive) to M (Manual) gives you the ability to manually change gears. The current gear will be displayed in the instrument cluster . Press the (+)/(–) buttons on the gearshift lever to manually make shifts: • Press (+) on the gearshift lever button to manually upshift the transmission.
In order to prevent the engine from running at too low an RPM, which may cause it to stall, the SST will still automatically make some downshifts if it has determined that you have not downshifted in time.
Brake-shift interlock W ARNING: Do not drive your vehicle until you verify that the brake lamps are working. W ARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely . T o avoid unwanted vehicle movement, always fully set the parking brake prior to doing this procedure.
4. Place fingers into hole where the gearshift lever boot was removed from and pull top half of shroud up and forward to separate it from the lower half of the shroud.
Brake-Shift Interlock – Floor-Shifter Assembly W ARNING: Do not drive your vehicle until you verify that the brakelamps are working. W ARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely .
3. Locate the brake shift interlock lever on the passenger side of the shifter assembly . 4. Apply the brake pedal. Using a screwdriver (or similar tool), press and hold the brake shift interlock lever while pulling the gearshift lever out of the P (Park) position and into the N (Neutral) position.
W ARNING: During all times, you are responsible for controlling the vehicle, supervising the hill start assist system and intervening, if required. W ARNING: If the engine is revved excessively , or if a malfunction is detected when the hill start assist feature is active, the hill start assist feature will be deactivated.
USING FOUR-WHEEL DRIVE (4WD) (IF EQUIPPED ) W ARNING: For important information regarding safe operation of this type of vehicle, see General Information in the Wheels and T ires chapter . Note: Do not use 4X4 mode on dry , hard surfaced roads. Doing so will produce excessive noise, increase tire wear and may damage drive components.
Using the Electronic Shift on the Fly 4WD system (If Equipped) 2H (4X2) - Delivers power to the rear wheels only . This mode is appropriate for normal on-road driving and provides the best fuel economy and smoothness. 4H (4X4 HIGH) - provides mechanically locked four -wheel drive power to the front and rear wheels.
Shifting between 2H (4X2) and 4H (4X4 High) Move the 4WD control between 2H (4X2) and 4H (4X4 HIGH) at any forward speed. The message center will display 4X4 SHIFT IN PROGRESS during the system shift. 4X4 HIGH will display in the message center if 4H is selected and 4X2 will momentarily display in the message center if 2H is selected.
Using the 2-Speed Automatic 4WD System (If Equipped) This system includes an electronically controlled transfer case with a high capacity clutch. The system is interactive with the road, continually monitoring and adjusting torque delivery to the front and rear wheels to optimize traction.
Note: Do not use 4L (4X4 LOW) on dry , hard surfaced roads. Doing so can produce excessive noise and increased tire wear . 4L (4X4 LOW) is only intended for consistently slippery or loose surfaces. Use of 4L (4X4 LOW) on these surfaces may produce some noise (such as occasional clunks), but will not damage drive components.
Note: Some noise may be heard as the system shifts or engages; this is normal. Note: 4x4 low mode is not intended for use on dry pavement Electronic Locking Differential (ELD) (If Equipped) Note: The ELD is designed for off-road use only and is not intended for use on dry pavement.
Activating the Electronic Locking Differential Note: Do not use ELD on dry , hard surfaced roads. Doing so will produce excessive noise and vibration and increase tire wear . Note: If the ELD has difficulty disengaging, release the accelerator pedal and turn the steering wheel in the opposite direction while rolling.
T ruck and utility vehicles can differ from some other vehicles. Y our vehicle may be higher to allow it to travel over rough terrain without getting hung up or damaging underbody components. The differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car .
For vehicles equipped with a 3.5L Ecoboost™ engine: Y our vehicle is equipped with an underbody transmission shield and brackets that may become damaged (due to reduced ground clearance) when taking your vehicle off-road. Remove the shield by disengaging the fasteners at each corner of the shield.
If your vehicle gets stuck W ARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander . Note: Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur .
Mud and water Note: Driving through deep water may damage the vehicle. If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly .
Driving on hilly or sloping terrain Note: A void driving crosswise or turning on steep slopes or hills. Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down.
Driving on snow and ice W ARNING: If you are driving in slippery conditions that require tire chains or cables, then it is critical that you drive cautiously . Keep speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death.
Parking W ARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer . W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park).
GENERAL INFORMA TION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn out and should be inspected by an authorized dealer .
Anti-Lock Brake System This system helps you maintain steering control during emergency stops by keeping the brakes from locking. The anti-lock brake system lamp momentarily illuminates when the ignition is turned on.
PRINCIPLES OF OPERA TION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time.
PRINCIPLES OF OPERA TION W ARNING: V ehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction or wheel and tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the AdvanceT rac® system.
A V ehicle without AdvanceT rac® with RSC® skidding off its intended route. B V ehicle with AdvanceT rac® with RSC® maintaining control on a slippery surface. USING ADV ANCETRAC® WITH RSC® The system automatically activates when you start your engine.
AdvanceT rac® with RSC® Features Button functions Stability control OFF light RSC® ESC TCS Button pressed and held for more than 5 seconds at vehicle speed under 35 mph (56 km/h) Flashes then illum.
HILL DESCENT CONTROL™ (IF EQUIPPED) W ARNING: Hill descent control cannot control descent in all surface conditions and circumstances, such as ice or extremely steep grades. Hill descent control is a driver assist system and cannot substitute for good judgment by the driver .
Whether accelerating or decelerating, once the desired descent speed is reached, remove your feet from the pedals and the chosen vehicle speed will be maintained. Note: Noise from the ABS pump motor may be observed during hill descent control operation.
SENSING SYSTEM (IF EQUIPPED) W ARNING: T o help avoid personal injury , please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at parking speeds.
The sensing system warns the driver of obstacles within a certain range of the bumper area. The system turns on automatically whenever the ignition is switched on. When receiving a detection warning, the radio volume is reduced to a predetermined level.
REAR VIEW CAMERA SYSTEM (IF EQUIPPED) W ARNING: The rear view camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with the interior and exterior mirrors for maximum coverage.
Using the Rear View Camera System The rear view camera system displays what is behind your vehicle when you place the transmission in R (Reverse). The system uses two types of guides to help you see what is behind your vehicle: 1.
Guidelines and the Centerline Note: Fixed guidelines are only available when the transmission is in R (Reverse). Note: The centerline is only available if fixed guidelines are on. A. Rear bumper B. Fixed guideline: Red zone C. Fixed guideline: Y ellow zone D.
Manual Zoom W ARNING: When manual zoom is on, the full area behind the vehicle is not shown. Be aware of your surroundings when using the manual zoom feature. Note: Manual zoom is only available when the transmission is in R (Reverse). Note: When manual zoom is enabled, only the centerline is shown.
PRINCIPLES OF OPERA TION Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. USING CRUISE CONTROL (IF EQUIPPED) W ARNING: Do not use cruise control in heavy traffic or on roads that are winding, slippery or unpaved.
Changing the Set Speed Note: If you accelerate by pressing the accelerator pedal, the set speed will not change. When you release the accelerator pedal, you will return to the speed that you previously set. • Press and hold SET + or SET – . Release the control when you reach the desired speed.
STEERING Electric power steering (3.7L, 5.0L and 3.5L EcoBoost™ engines) W ARNING: The electric power steering system has diagnostic checks that continuously monitor the system to ensure proper operation.
When a steering system error is detected, the following messages may appear in the information display: • Service Power Steering • Service Power Steering Now • Power Steering Assist Fault Hydraulic steering (6.2L engine) Y our vehicle is equipped with a hydraulic steering system.
LOAD LIMIT V ehicle Loading – With and Without a T railer This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance.
W ARNING: The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available.
Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
W ARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GA WR limitations.
• Suppose your vehicle has a 1400 lb. (635 kg) cargo and luggage capacity . Y ou and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb.
T AILGA TE T ailgate Lock (If Equipped) The tailgate lock is designed to help prevent theft of the tailgate. Insert the ignition key into the tailgate lock.
4. Lower the tailgate. 5. Using a screwdriver , gently pry the spring clip (on each connector) past the head of the support screw . Disconnect the cable. 6. Disconnect the other cable. 7. Lift tailgate to a 45-degree angle from horizontal. 8. Lift the right side off of its hinge.
Opening the T ailgate Step 1. Flip down the tailgate. 2. Pull the yellow latch lever to the unlock position to release the grab handle from its stowed position. 3. Raise the handle upright until you feel it latch and see the latch lever in the lock position.
Box Side Step (If Equipped) The box side step allows easier access to the truck bed. Note: Do not drive the vehicle with a box side step in the deployed position. Note: The box side step load carrying capability (one person plus cargo) is 500 pounds (227 kilograms).
BED EXTENDER (IF EQUIPPED) Note: This feature is not intended for off-road usage. Note: Make sure the locking pins and knobs are fully engaged when the vehicle is in motion. Note: Make sure all cargo is secured. Note: The tailgate load must not exceed 150 pounds (68 kilograms) when the vehicle is in motion.
3. Rotate the panels toward the tailgate. Repeat Steps 1–3 for the other side of the bed extender . 4. Connect the two panels, then rotate both knobs a quarter -turn clockwise to secure the panels. 5. Make sure the latch rod is inserted into the tailgate hole and the locking pins on both sides are engaged into their holes in the pick-up box.
T o open the bed extender into grocery mode, follow Steps 1–4 by rotating the panels away from the tailgate. Close the tailgate. POWER DEPLOY ABLE RUNNING BOARDS (IF EQUIPPED) W ARNING: In extreme climates, excessive ice buildup may occur , causing the running boards not to deploy .
The running boards automatically move when the doors are opened to assist entering and exiting the vehicle. Automatic Power Deploy The running boards will extend down and out when the doors are opened. Automatic Power Stow The running boards will return to the stowed position after a two second delay when the doors are closed.
TOWING A TRAILER W ARNING: Do not exceed the GVWR or the GA WR specified on the certification label. W ARNING: T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of.
TRAILER SW A Y CONTROL (IF EQUIPPED) W ARNING: T urning off trailer sway control increases the risk of loss of vehicle control, serious injury or death.
Note: Certain states require electric trailer brakes for trailers over a specified weight. Be sure to check state regulations for this specified weight. The maximum trailer weights listed may be limited to this specified weight, as your vehicle’ s electrical system may not include the wiring connector needed to use electric trailer brakes.
Regular Cab Engine Rear axle ratio Maximum GCWR - lb. (kg) Four–wheel drive 126–inch wheelbase 3.7L 3.73 10900 (4944) 5.0L 3.55 12900 (5851) 3.73 13300 (6033) T wo–wheel drive 145–inch wheelbase 3.5L 3.15 14000 (6350) 3.55 15000 (6804) 3.5L (Heavy Duty Payload Package) 3.
SuperCab Engine Rear axle ratio Maximum GCWR - lb. (kg) Four–wheel drive 133–inch wheelbase 6.2L (SVT Raptor) 4.10 12500 (5670) T wo–wheel drive 145–inch wheelbase 3.5L 3.15 14000 (6350) 3.55 15200 (6895) 3.5L (MAX T railer T ow Package) 3.73 16900 (7666) 3.
SuperCab Engine Rear axle ratio Maximum GCWR - lb. (kg) 5.0L 3.31 13500 (6123) 3.55 14900 (6759) 5.0L (Heavy Duty Payload Package) 3.73 15300 (6940) Four–wheel drive 163–inch wheelbase 3.5L 3.31 14000 (6350) 3.55 and 3.73 15400 (6985) 3.5L (Heavy Duty Payload Package) 3.
SuperCrew Engine Rear axle ratio Maximum GCWR - lb. (kg) 6.2L (MAX T railer T ow Package) 3.73 17100 (7756) Four–wheel drive 145–inch wheelbase 3.5L (Limited) 3.73 13400 (6078) 3.5L 3.31 14000 (6350) 3.55 and 3.73 15500 (7031) 3.5L (MAX T railer T ow Package) 3.
SuperCrew Engine Rear axle ratio Maximum GCWR - lb. (kg) Four–wheel drive 157–inch wheelbase 3.5L 3.31 14000 (6350) 3.55 and 3.73 15500 (7031) 3.5L (MAX T railer T ow Package) 3.73 and 4.10 17100 (7756) 3.5L (Heavy Duty Payload Package) 3.73 17100 (7756) 5.
Hitches Do not use a hitch that either clamps onto the bumper or attaches to the axle. Distribute the trailer load so 10-15% of the total trailer weight is on the tongue.
Safety Chains Note: Do not attach safety chains to the bumper . Always connect the trailer’ s safety chains to the frame or hook retainers of your vehicle hitch. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow enough slack for turning tight corners.
When used properly , the trailer brake controller assists in smooth and effective trailer braking by powering the trailer’ s electric or electric-over -hydraulic brakes with a proportional output based on the towing vehicle’ s brake pressure. The controller user interface consists of the following: A.
• TRAILER DISCONNECTED: Displays, accompanied by a single audible chime, when the system senses a trailer connection and then a disconnection, either intentional or unintentional, during a given ignition cycle. It also displays if a truck or trailer -wiring fault occurs causing the trailer to appear disconnected.
6. If the trailer wheels lock up, indicated by squealing tires, reduce the gain setting. If the trailer wheels turn freely , increase the gain setting.
• The trailer brake controller is equipped with a feature that reduces output at vehicle speeds below 11 mph (18 km/h) so trailer and vehicle braking is not jerky or harsh. This feature is only available when applying the brakes using your vehicle’ s brake pedal, not the controller .
When T owing a T railer • Do not drive faster than 70 mph (113 km/h) during the first 500 miles (800 kilometers). • Do not make full-throttle starts. • Check your hitch, electrical connections and trailer wheel lug nuts thoroughly after you have traveled 50 miles (80 kilometers).
• A void parking on a grade. However , if you must park on a grade: 1. T urn the steering wheel to point your vehicle tires away from traffic flow . 2. Set your vehicle parking brake. 3. Place the automatic transmission in position P. 4. Place wheel chocks in front and back of the trailer wheels.
TRANSPORTING THE VEHICLE If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . W e recommend the use of a wheel lift and dollies or flatbed equipment to tow your vehicle.
TOWING THE VEHICLE ON FOUR WHEELS Emergency T owing If your vehicle becomes inoperable (without access to wheel dollies, car -hauling trailer , or flatbed transport vehicle), it can be flat-towed (all.
Four-wheel-down T owing 1. T urn the ignition to the on position. Do not start the engine. 2. Press and hold the brake pedal. 3. Shift the 4WD switch to 2H. 4. Shift the transmission to position N. 5. Rotate the 4WD switch from 2H to 4L and back to 2H five times within seven seconds.
W ARNING: Failing to put the transfer case in its neutral position will damage vehicle components. Note: Y ou can check four -wheel-down towing status at any time by opening the driver’ s door or turning the ignition to the accessory or on position and verifying the NEUTRAL TOW ENABLED message displays in the cluster .
BREAKING-IN Y ou need to break in new tires for approximately 300 miles (480 kilometers). During this time, your vehicle may exhibit some unique driving characteristics. A void driving too fast during the first 1000 miles (1600 kilometers). V ary your speed frequently and change up through the gears early .
• Rest your foot on the brake pedal while driving. • Drive a heavily loaded vehicle or tow a trailer . • Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost for every 400 pounds [180 kilograms] of weight carried). • Add particular accessories to your vehicle (e.
FLOOR MA TS W ARNING: Always use floor mats that are designed to fit the footwell of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured to retention posts so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways.
W ARNING (Continued) • Failure to properly follow floor mat installation or attachment instructions can potentially cause interference with pedal operation causing loss of control of vehicle. • T o install floor mats, position the floor mat so that the eyelet is over the retention post and press down to lock in.
• Rear ballast weight behind the rear axle may be required to prevent exceeding the FGA WR, and provide front-to-rear weight balance for proper braking and steering. • Front wheel toe may require re-adjustment to prevent premature uneven tire wear .
Snowplowing with your Air Bag Equipped V ehicle W ARNING: Do not attempt to service, repair , or modify the air bag supplemental restraint system (SRS) or its fuses. See your Ford or Lincoln Mercury dealer . W ARNING: Additional equipment such as snowplow equipment may effect the performance of the air bag sensors increasing the risk of injury .
Transmission operation while plowing W ARNING: Do not spin the wheels at over 35 mph (55 km/h). The tires may fail and injure a passenger or bystander . • Shift transfer case to 4L (4WD Low) when plowing in small areas at speeds below 5 mph (8 km/h).
ROADSIDE ASSIST ANCE V ehicles Sold in the U.S.: Getting Roadside Assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty .
V ehicles Sold in the U.S.: Using Roadside Assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. This card is found in the owner’ s manual portfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, call 1-800-241-3673.
HAZARD W ARNING FLASHERS The hazard flasher control is located on the instrument panel by the radio. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. • Press the flasher control and all front and rear direction signals will flash.
JUMP-ST ARTING THE VEHICLE W ARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. W ARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.
Connecting the Jumper Cables W ARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery .
Jump Starting 1. Start the engine of the booster vehicle and run the engine at a moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6K 0C8 T elephone 1-800-565-3673 (FORD) Online www .ford.
IN CALIFORNIA (U.S. ONL Y) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’ s applicable .
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONL Y) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-s.
UTILIZING THE MEDIA TION or ARBITRA TION PROGRAM (CANADA ONL Y) This pertains to vehicles delivered to authorized Canadian dealers. In those cases, where you continue to feel that the efforts by Ford .
If your vehicle must be serviced while you are traveling or living in Asia-Pacific Region, Sub-Saharan Africa, U.S. V irgin Islands, Central America, the Caribbean, and Israel, contact the nearest authorized dealer .
If you buy your vehicle in North America and then relocate to any of the above locations, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations & Global Growth Initiatives by emailing expcac@ford.
REPORTING SAFETY DEFECTS (U.S. ONL Y) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
CHANGING A FUSE Fuses W ARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in the vehicle are not working, a fuse may have blown.
FUSE SPECIFICA TION CHART Power Distribution Box W ARNING: Always disconnect the battery before servicing high current fuses. W ARNING: T o reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs.
Fuse or relay number Fuse amp rating Protected components 3 — Blower motor relay 4 — Rear window defroster relay 5 — Electric fan relay (high speed) 6 — T railer tow park lamp relay 7 — Run/start relay 8 — Fuel pump relay 9 — T railer tow battery charger relay 10 — Powertrain control module relay (3.
Fuse or relay number Fuse amp rating Protected components 26 10A* Powertrain control module – keep alive power and relay coil, canister vent solenoid (3.
Fuse or relay number Fuse amp rating Protected components 44 15A* Upfitter 3 (SVT Raptor), T railer tow power folding mirrors 45 10A* Alternator sensor (3.
Fuse or relay number Fuse amp rating Protected components 65 20A** Auxiliary power point (instrument panel) 66 20A** Auxiliary power point (inside center console) 67 20A** T railer tow park lamps rela.
Fuse or relay number Fuse amp rating Protected components 77 10A* Powertrain control module – V oltage power 3 (Emission related powertrain components, Electric fan relays coil) 78 15A* Powertrain control module – V oltage powe r4–I g n ition coils (3.
T o reinstall the fuse box cover , place the top part of the cover on the fuse panel, then push the bottom part of the cover until you hear it click shut.
Fuse or relay number Fuse amp rating Protected components 10 10A Run/accessory relay 11 10A Instrument cluster 12 15A Interior lighting, Puddle lamps, Backlighting, Cargo lamp 13 15A Right turn signal.
Fuse or relay number Fuse amp rating Protected components 32 15A Delay/accessory – moonroof, power windows, locks, Automatic dimming mirror/Compass, T railer tow power telescope mirrors 33 10A Rear .
Auxiliary relay box (SVT Raptor only) The relay box is located in the left rear corner of the engine compartment. Fuse/Relay location Fuse amp rating Description 1 — Upfitter 1 relay 2 — Upfitter .
GENERAL INFORMA TION W ARNING: T urn off the power running boards, if equipped, before working under the vehicle, jacking or placing any object under the vehicle. Never place your hand between the extended running board and the vehicle. A moving running board may cause injury .
Working with the Engine On W ARNING: T o reduce the risk of vehicle damage or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. 1. Set the parking brake and shift to position P .
UNDER HOOD OVERVIEW 3.7L V6 Engine A. W indshield washer fluid reservoir B. Battery C. Engine oil dipstick (out of view) D. Brake fluid reservoir E. Engine coolant reservoir F .
5.0L V8 Engine A. W indshield washer fluid reservoir B. Battery C. Engine oil filler cap D. Engine oil dipstick E. Brake fluid reservoir F . Engine coolant reservoir G.
6.2L V8 Engine A. W indshield washer fluid reservoir B. Engine oil dipstick C. Brake fluid reservoir D. Engine coolant reservoir E. Air filter assembly F .
3.5L V6 EcoBoost® Engine A. W indshield washer fluid reservoir B. Battery C. Engine oil filler cap D. Engine oil dipstick E. Brake fluid reservoir F .
ENGINE OIL DIPSTICK A. MIN B. MAX ENGINE OIL CHECK Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. T urn the engine off and wait 15 minutes for the oil to drain into the oil pan.
Adding Engine Oil Note: Do not remove the engine oil level dipstick or the filler cap when the engine is running. Note: Do not add engine oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage. Only use oils certified for gasoline engines by the American Petroleum Institute (API).
Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300-ROB75240 available from your dealer . Ford does not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations.
• In case of emergency , a large amount of water without engine coolant may be added in order to reach a vehicle service location. In this instance, the cooling system must be drained, chemically cleaned with Motorcraft Premium Cooling System Flush, and refilled with engine coolant as soon as possible.
If you drive in extremely hot climates: • It may be necessary to have a Ford authorized dealer decrease the coolant concentration to 40%. • A coolant concentration of 40% will provide improved overheat protection.
When Fail-Safe Mode is Activated W ARNING: Fail-safe mode is for use during emergencies only . Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs.
At this time, you may notice your engine coolant temperature gauge needle move toward the H and the POWER REDUCED TO LOWER TEMP message may appear in the information display . Y ou may notice a reduction in the vehicle’ s speed caused by reduced engine power .
AUTOMA TIC TRANSMISSION FLUID CHECK Note: T ransmission fluid should be checked by an authorized dealer . If required, fluid should be added by an authorized dealer . The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes.
BRAKE FLUID CHECK Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately .
CHANGING THE VEHICLE BA TTERY W ARNING: Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes.
If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. Y ou can neutralize the acid with a solution of baking soda and water . It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time.
If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
CHECKING THE WIPER BLADES Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth. CHANGING THE WIPER BLADES 1. T o remove the wiper blade, pull the wiper arm away from the vehicle.
Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and the windshield.
Changing the Air Filter Element (3.7L, 5.0L, and 6.2L Engines) 1. Locate the mass air flow sensor electrical connector on the air outlet tube. This connector will need to be unplugged. 2. Reposition the locking clip on the connector (connector shown from below for clarity), squeeze the connector and pull it off of the air outlet tube.
5. Release the three clamps that secure the cover to the air filter housing. Push the air filter cover toward the center of the vehicle and up slightly to release it. 6. Remove the air filter element from the air filter housing. 7. Install a new air filter element.
Changing the Air Filter Element (3.5L EcoBoost Engine) 1. Locate the sensor electrical connector on the air outlet tube (1). This connector will need to be unplugged. 2. Pull up to disconnect wiring harness (2). 3. Disconnect the sensor by pressing the retaining tab and pulling back on the lead.
ADJUSTING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, the alignment of your headlamps should be checked by your authorized dealer . V ertical Aim Adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.
For V ehicles With HID Headlamps: There is a distinct cut-off (change from light to dark) in the left portion of the beam pattern. The top edge of this cut-off should be positioned 2 inches (5 centimeters) below the horizontal reference line. 4. Locate the vertical adjuster on each headlamp.
These are examples of unacceptable moisture (usually caused by a lamp water leak): • W ater puddle inside the lamp. • Large water droplets, drip marks or streaks present on the interior of the lens. T ake your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present.
6. Remove the bulb and socket by turning it counterclockwise, then pull it straight out. W ARNING: Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
5. Remove the bulb and socket by turning it counterclockwise, then pull it straight out. 6. Pull the bulb straight out of the socket. Install the new bulb(s) in reverse order . Replacing T ail, Brake, Turn signal, and Backup Lamp Bulbs 1. Make sure the headlamp control is in the off position.
Replacing High-Mount Brake and Cargo Lamp Bulbs Make sure the headlamp control is in the off position. 1. Remove the two screws and move the lamp assembly away from the vehicle to expose the bulb sockets. 2. Remove the bulb socket by rotating counterclockwise and pulling it out of the lamp assembly .
Replacing License Plate Lamp Bulbs The license plate bulbs are located behind the rear bumper . T o change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. T wist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly .
Function Number of bulbs T rade number Rear stop/turn/side marker/tail lamp 4 3057K LCP High-mount brake lamp 1 912 Front row map lamps 2 W5W Rear dome lamp 1 578 Rear dome/courtesy lamps 3 578 High m.
GENERAL INFORMA TION Y our Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. CLEANING PRODUCTS For best results, use the following p.
• Dry the vehicle with a chamois or soft, terry cloth towel in order to eliminate water spotting. • It is especially important to wash the vehicle regularly during the winter months, as dirt and road salt are difficult to remove and cause damage to the vehicle.
Cleaning Plastic Exterior Parts Use only approved products to clean plastic parts. • For routine cleaning, use Motorcraft® Detail W ash. • If tar or grease spots are present, use Motorcraft® Bug and T ar Remover . W AXING • W ash the vehicle first.
• Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage. • Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations.
CLEANING THE INTERIOR W ARNING: Do not use cleaning solvents, bleach or dye on the vehicle’ s safety belts, as these actions may weaken the belt webbing. W ARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents.
CLEANING THE INSTRUMENT P ANEL AND INSTRUMENT CLUSTER LENS W ARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system.
Instrument Panel, Door Panels and Console (FX appearance package) Y our vehicle’ s instrument panel, door panels and console are uniquely painted with both high and low gloss paints that require special care.
CLEANING LEA THER SEA TS (IF EQUIPPED, EXCEPT FOR THE KING RANCH® EDITION) Note: For the King Ranch® Edition leather seats, refer to a separate section in this chapter . • Clean spills and stains as quickly as possible. • For routine cleaning, wipe the surface with a soft, damp cloth.
Scratches Natural Markings - Because the leather in the seat comes from genuine steer hides, there will be evidence of naturally occurring markings, such as small scars. These markings give character to the seating covers and should be considered as proof of a genuine leather product.
VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time (30 days or more), read the following maintenance recommendations to make sure your vehicle stays in good operating condition. All motor vehicles and their components were engineered and tested for reliable, regular driving.
Fuel system • Fill the fuel tank with high-quality fuel until the first automatic shutoff of the fuel pump nozzle. Note: During extended periods of vehicle storage (30 days or more), fuel may deteriorate due to oxidation. Add a quality gas stabilizer product to the vehicle fuel system whenever actual or expected storage periods exceed 30 days.
Removing V ehicle from Storage When your vehicle is ready to come out of storage, do the following: • W ash your vehicle to remove any dirt or grease film build-up on window surfaces. • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collected during storage (mice/squirrel nests).
GENERAL INFORMA TION Notice to Owners About High Performance Tires Note: Y our vehicle is equipped with high performance tires. When first driving the vehicle after it has been parked for a period of time, you may experience a temporary ride disturbance.
Four-Wheel Drive System (If Equipped) W ARNING: Do not become overconfident in the ability of four -wheel drive vehicles. Although a four -wheel drive vehicle may accelerate better than a two-wheel drive vehicle in low-traction situations, it will not stop any faster than two-wheel drive vehicles.
How Y our Vehicle Differs from Other V ehicles Sport-utility vehicles, vans and trucks can differ from some other vehicles in a few noticeable ways. Y our vehicle may be: • Higher – to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components.
TIRE CARE Information About Uniform Tire Quality Grading T ire Quality Grades apply to new pneumatic passenger car tires. The T ire Quality Grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
T raction AA A B C W ARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. The traction grades, from highest to lowest are AA, A, B, and C.
• Standard load: A class of P-metric or Metric tires designed to carry a maximum load at 35 psi [37 psi (2.5 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’ s load-carrying capability .
Information on P T ype Tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
G. H: Indicates the tire’ s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure.
J. T ire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber -coated fabric in the tire tread and sidewall. T ire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester , and others.
Additional Information Contained on the Tire Sidewall for L T Type Tires L T type tires have some additional information beyond those of P type tires. These differences are described below . Note: T ire Quality Grades do not apply to this type of tire.
Information on T T ype Tires T type tires have some additional information beyond those of P type tires. These differences are described below . T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
INFLA TING YOUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required.
Maximum Inflation Pressure is the tire manufacturer’ s maximum permissible pressure or the pressure at which the maximum load can be carried by the tire.
Note: Some spare tires operate at a higher inflation pressure than the other tires. For T -type mini-spare tires, see the Dissimilar Spare T ire and Wheel Assembly Information section.
Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall). If damage is observed or suspected, have the tire inspected by a tire professional.
Tire Replacement Requirements W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford.
Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. The two front tires or two rear tires should generally be replaced as a pair . The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels.
Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you are driving, the wheels may be out of alignment.
• Rear -wheel drive vehicles/ Four -wheel drive vehicles (front tires at left of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. USING SNOW CHAINS W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford.
TIRE PRESSURE MONITORING SYSTEM W ARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge. See Inflating Y our T ires in this chapter .
telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly . The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada.
When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn you when your tires need air .
Low tire pressure warning light Possible cause Customer action required Flashing warning light Spare tire in use Repair the damaged road wheel and tire and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section.
Tire Pressure Monitoring System Reset Procedure W ARNING: T o determine the required pressure(s) for your vehicle, see the Safety Compliance Certification Label (affixed to either the door hinge pilla.
Performing the System Reset Procedure Read the entire procedure before attempting. 1. Drive the vehicle above 20 mph (32 km/h) for at least two minutes and then park in a safe location where you can easily get to all four tires and have access to an air pump.
T raining is complete after the horn sounds for the last tire trained (driver’ s side rear tire), the system indicator stops flashing, and a message is shown in the information display (if equipped). 10. T urn the ignition off. If two short horn beeps are heard, the reset procedure was unsuccessful and must be repeated.
Dissimilar Spare Tire and Wheel Assembly Information W ARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire and wheel assembly , then it is intended for temporary use only .
• Winter weather driving capability • W et weather driving capability • All-wheel driving capability 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire and wheel assembly , do not: • exceed 70 mph (113 km/h).
Tire Change Procedure W ARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission selector lever is in position P .
Park on a level surface, activate the hazard flashers and set the parking brake. Then, place the transmission selector lever in position P and turn the engine off. Location of the spare tire and tools The spare tire is located under the vehicle, just forward of the rear bumper .
Removing the spare tire 1. Use the ignition key to remove the lock cylinder from the access hole of the bumper to allow access to the guide tube. Assemble the jack handle as shown in the illustration. 2. Fully insert the jack handle through the bumper hole and into the guide tube through the access hole in the rear bumper .
7. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. • Front Note: Use the frame rail as the jacking location point, NOT the control arm. Note: For the F-150 SVT Raptor , you must always use the jack saddle extension.
8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered.
Stowing the Flat or Spare Tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing in the direction specified on the T ire Changing Instructions located with the jack hardware.
TECHNICAL SPECIFICA TIONS Wheel Lug Nut T orque Specifications W ARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel.
ENGINE SPECIFICA TIONS Engine 3.7L V6 Engine 5.0L V8 Engine 6.2L V8 Engine 3.5L V6 EcoBoost Engine Cubic inches 226 302 378 214 Fuel Minimum 87 octane or E85 Minimum 87 octane or E85 Minimum 87 octane.
6.2L engine 3.5L EcoBoost engine 398 Capacities and Specifications 2013 F-150 (f12) Owners Guide gf, 3rd Printing, February 2013 USA (fus) I n f o r m a t i o n P r o v i d e d b y :.
TECHNICAL SPECIFICA TIONS Item Capacity Ford part name or equivalent Ford part number / Ford specification Brake fluid Between MIN/MAX on brake fluid reservoir Motorcraft® High Performance DOT 3 Motor V ehicle Brake Fluid PM-1-C / WSS-M6C62-A or WSS-M6C65-A1 3.
Item Capacity Ford part name or equivalent Ford part number / Ford specification 3.5L EcoBoost engine oil 1,2 6.0 quarts (5.7L) • Motorcraft® SAE 5W -30 Premium Synthetic Blend Motor Oil (US) • M.
Item Capacity Ford part name or equivalent Ford part number / Ford specification Rear axle fluid 4,5 5.5 pints (2.6L) Motorcraft® SAE 75W -140 Rear Synthetic Axle Lubricant XY -75W140-QL / WSL-M2C192.
Item Capacity Ford part name or equivalent Ford part number / Ford specification Automatic transmission fluid (6R80) 7,8 12.1 quarts (11.7L) (3.7L engine) Motorcraft® MERCON® L V AT F XT -10-QL V / MERCON® L V 13.1 quarts (12.4L) (5.0L engine) 13.1 quarts (12.
Item Capacity Ford part name or equivalent Ford part number / Ford specification Fuel tank SuperCrew 5.5’ box 26.0 gallons (98.4L) Standard 36.0 gallons (136.2L) Optional —— Fuel tank SuperCrew 6.5’ box 26.0 gallons (98.4L) Standard 36.0 gallons (136.
5 Y our vehicle’ s rear axle is filled with a synthetic rear axle lubricant and is considered lubricated for life. These lubricants do not need to be checked or changed unless a leak is suspected, service is required or the axle assembly has been submerged in water .
MOTORCRAFT® P ART NUMBERS Component 3.7L V6 engine 5.0L V8 engine 6.2L V8 engine 3.5L V6 EcoBoost engine Air filter element F A-1883 F A-1883 F A-1883 F A-1883 Battery BXT -65-750 BXT -65-750 BXT -65.
VEHICLE IDENTIFICA TION NUMBER The vehicle identification number is located on the driver’ s side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number . The V ehicle Identification Number (VIN) contains the following information: A.
VEHICLE CERTIFICA TION LABEL The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
ACCESSORIES For a complete listing of the accessories that are available for your vehicle, please contact your dealer or visit our online store at: Accessories.Ford.com (U.S. only). Ford Custom Accessories are available for your vehicle through your local Ford or Ford of Canada dealer .
Lifestyle • Ash cup / smoker’ s package • Racks and carriers* • Bedliners and bedmats • T ruck bed camping tent* • Bed side step • Sportliner cargo liner* • T owing mirrors • Rear se.
For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your veh.
FORD ESP EXTENDED SER VICE PLANS PROTECT YOURSELF FROM THE RISING COST OF VEHICLE REP AIRS WITH A FORD EXTENDED SERVICE PLAN. SERVICE PLANS (U.S. only) More than 32 Million Ford and Lincoln owners have discovered the powerful protection Ford ESP .
Roadside Assistance Exclusive 24/7 roadside assistance, including: • T owing, flat-tire change and battery jump starts • Out of fuel and lock-out assistance • T ravel Expense reimbursement for l.
Interest Free Financing Options Available T ake advantage of our interest free installment payment plan. Just a 10% down payment will provide you with an affordable, no interest, no fee payment program.
GENERAL MAINTENANCE INFORMA TION Why Maintain Y our V ehicle? Carefully following the maintenance schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it.
Protecting Y our Investment Maintenance is an investment that pays dividends in the form of improved reliability , durability and resale value. T o maintain the proper performance of your vehicle and its emission control systems, it is imperative that scheduled maintenance be completed at the designated intervals.
Additives and Chemicals Ford Motor Company recommended additives and chemicals are listed in this book and in the W orkshop Manual. Additional chemicals or additives not approved by Ford Motor Company are not recommended as part of normal maintenance.
Multi-point Inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly . This can help identify potential issues and prevent major problems.
418 Scheduled Maintenance 2013 F-150 (f12) Owners Guide gf, 3rd Printing, February 2013 USA (fus) I n f o r m a t i o n P r o v i d e d b y :.
NORMAL SCHEDULED MAINTENANCE AND LOG V ehicles Equipped with a 3.5L, 3.7L or 5.0L Engine Y our vehicle is equipped with an Intelligent Oil-Life Monitor that determines when the engine oil should be changed based on how your vehicle is used.
Normal scheduled maintenance * At every oil change interval as indicated by the information display Change engine oil and filter . ** Rotate tires, inspect tire wear and measure tread depth. Perform multi-point inspection (recommended). Inspect automatic transmission fluid level (if equipped with dipstick).
Other maintenance items 1 Every 30000 miles (48000 km) Replace climate-controlled (heated and cooled) seat filter (if equipped). Replace engine air filter . At 100000 miles (160000 km) Change engine coolant. 2 Every 100000 miles (160000 km) Replace spark plugs.
V ehicles Equipped with a 6.2L Engine The following section contains the Normal Scheduled Maintenance. This schedule is presented at specific mileage (kilometer) intervals with exceptions as noted. Normal scheduled maintenance Every 7500 miles (12000 km) or six months (whichever comes first) Change engine oil and filter .
Other maintenance items Every 30000 miles (48000 km) Replace climate-controlled (heated and cooled) seat filter (if equipped). Replace engine air filter . Every 97500 miles (156000 km) Replace spark plugs. Every 105000 miles (168000 km) Change engine coolant.
Maintenance Schedule Log D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A .
D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D A.
D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D A.
SPECIAL OPERA TING CONDITIONS – 3.5L, 3.7L and 5.0L ENGINES If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the additional maintenance.
Operating in dusty or sandy conditions such as unpaved or dusty roads Inspect frequently , service as required Replace engine air filter . Every 5000 miles (8000 km) Inspect the wheels and related components for abnormal noise, wear , looseness or drag.
SPECIAL OPERA TING CONDITIONS – 6.2L ENGINE If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the additional maintenance.
* Reset your oil life monitoring system after each engine oil and filter change. See the Instrument Cluster chapter . Operating in dusty or sandy conditions such as unpaved or dusty roads Inspect frequently , service as required Replace engine air filter .
Special Operating Condition Log D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P.
D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D A.
EXCEPTIONS Normal vehicle axle maintenance: Rear axles and power take-off units with synthetic fluid and light-duty trucks equipped with Ford-design axles are lubricated for life; do not check or change fluid unless a leak is suspected, service is required or the assembly has been submerged in water .
ENGINE COOLANT CHANGE RECORD 3.5L, 3.7L and 5.0L engines Initial change Six years or 100000 miles (160000 km) (whichever comes first) After initial change Every three years or 50000 miles (80000 km) 6.
SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cellular phone and portable media player . This allows you to: • Make and receive calls. • Access and play music from your portable music player . • Use 911 Assist, V ehicle Health Report and SYNC Services (T raffic, Directions & Information) (if equipped).
GENERAL INFORMA TION Make sure you review your device’ s manual before using it with SYNC. Support The SYNC support team is available to help you with any questions you cannot answer on your own. Monday-Saturday , 8:30am-8:00pm EST . In the United States, call: 1–888–270–1055.
When using SYNC: • Do not operate playing devices if the power cords or cables are broken, split or damaged. Place cords and cables out of the way , so they do not interfere with the operation of pedals, seats, compartments or safe driving abilities.
USING VOICE RECOGNITION This system helps you control many features using voice commands. This allows you to keep your hands on the wheel and focus on what is in front of you. Initiating a V oice Session Push the voice icon; a tone sounds and Listening appears in the display .
Adjusting the Interaction Level Push the voice icon; when prompted, say “V oice settings”, then any of the following: When you say: The system: “Interaction mode standard” Provides more detailed interaction and guidance. “Interaction mode advanced” Provides less audible interaction and more tone prompts.
Helpful Hints • Make sure the interior of the vehicle is as quiet as possible. Wind noise from open windows and road vibrations may prevent the system from correctly recognizing spoken commands. • After pressing the voice icon, wait until after the tone sounds and Listening appears before saying a command.
Pairing a Phone for the First Time Note: SYNC can support downloading up to approximately 2000 entries per Bluetooth-enabled cellular phone. Note: Make sure the vehicle ignition and radio are turned on and the transmission is in position P. Note: T o scroll through the menus, press the up and down arrows on your audio system.
Phone V oice Commands Press the voice icon and say “Phone”. Say any of the following: “PHONE” “Call <name>” 1,2 “Call <name> on mobile OR cell” 1,2 “Call <name> on .
“MENU” “(Phone) connections” * “(Phone) settings (message) notification off” * “(Phone) settings (message) notification on” * “(Phone) settings (set) phone ringer” * “(Phone) set.
Making Calls Press the voice icon and when prompted say: 1. Say “Call <name>” or “Dial”, then the desired number . 2. When the system confirms the number , say “Dial” again to initiate the call. T o erase the last spoken digit, say “Delete” or press the left arrow button.
When you select: Y ou can: Join Calls Join two separate calls. 1. Press the phone button. 2. Access the desired contact through SYNC or use voice commands to place the second call. Once actively in the second call, press MENU. 3. Scroll until Join Calls appears and press OK.
Accessing Features through the Phone Menu SYNC’ s phone menu allows you to redial a number , access your call history and phone book and send text messages as well as access phone and system settings. Y ou can also access advanced features, such as 911 Assist, V ehicle Health Report and SYNC Services.
When you select: Y ou can: T ext Message 1 Enables you to send, download and delete text messages. Phone Settings 1 Allows you to view your phone’ s status, set ring tones, select your message notification, change phone book entries and automatically download your cellular phone among other features.
Receiving a T ext Message Note: This is a phone-dependent feature. Y our phone must support downloading text messages using Bluetooth to receive incoming text messages. Note: Forwarding a text message is a speed-dependent feature and can only be done when the vehicle is traveling at 3 mph (5 km/h) or less.
Note: SYNC does not automatically download all of your unread text messages at every ignition cycle (as it does with call history and phonebook if automatic download is set to on). Return exits the current menu when you press OK. If you select Send T ext Message? : 1.
Accessing Y our Phone Settings These are phone-dependent features. Y our phone settings allow you to access and adjust features such as your ring tone, text message notification, modify your phone book and also set up automatic download. 1. Press the phone button.
When you select: Y ou can: Modify Phonebook Modify the contents of your phone book (i.e., add, delete, download). Press OK to select and scroll between: Add Contacts: Press OK to add more contacts from your phone book. Push the desired contact(s) on your phone.
System Settings System Settings provide access to your Bluetooth Devices and Advanced menu features. Use the arrow buttons to scroll through the menu options. The Bluetooth Devices menu allows you to add, connect, delete and set a phone as primary as well as turn your Bluetooth feature on and off.
If you select: Y ou can: Set Bluetooth On/Off T urn the Bluetooth feature on and off. Press OK and scroll to toggle between On and Off. When the desired selection is chosen, press OK. Note: T urning Bluetooth off disconnects all Bluetooth devices and deactivates all Bluetooth features.
If you select: Y ou can: Prompts Get help from SYNC by using questions, helpful hints or asking you for a specific action. T o turn these prompts on or off: 1. Press OK to select and scroll to select between on or off. 2. Press OK when the desired selection appears in the display .
If you select: Y ou can: Install Application Install applications you have downloaded. Press OK and scroll to select. Press OK to confirm. System Info Access the Auto V ersion number as well as the FPN number . Press OK to select. MAP Profile This is a Bluetooth component which can further help your phone with the exchange of text messages.
W ARNING: Always place your phone in a secure location in the vehicle so it does not become a projectile or get damaged in a crash. Failure to do so may cause serious injury to someone or damage the phone which could prevent 911 Assist from working properly .
T o make sure that 911 Assist works properly: • SYNC must be powered and working properly at the time of the incident and throughout feature activation and use. • SYNC 911 Assist feature must be set on prior to the incident. • A Bluetooth-enabled and compatible phone has to be paired and connected to SYNC.
91 1 Assist Privacy Notice Once 911 Assist is set on, it may disclose to emergency services that the vehicle has been in a crash involving the deployment of an airbag or activation of the fuel pump shut-off.
The system allows you to check your vehicle’ s overall health in the form of a diagnostic report card. The vehicle health report contains valuable information such as: • V ehicle Diagnostic Information • Scheduled maintenance • Open Recalls and Field Service Actions • Unserviced items from vehicle inspections by your authorized dealer .
V ehicle Health Report Privacy Notice When you run a V ehicle Health Report, Ford Motor Company may collect your cellular phone number (to process your report request) and diagnostic information about your vehicle. Certain versions or updates to V ehicle Health Report may also collect additional vehicle information.
Note: When you connect, the service uses GPS technology and advanced vehicle sensors to collect the vehicle’ s current location, travel direction and speed to help provide you with the directions, traffic reports, or business searches you request.
Receiving Turn-by-T urn Directions 1. When connected to SYNC Services, say “Directions” or “Business search”. T o find the closest business or type of business to your current location, just say “Business search” and then “Search near me”.
Disconnecting from SYNC Services 1. Press and hold the phone button on the steering wheel. 2. Say “Good-bye” from the SYNC Services main menu. SYNC Services quick tips Personalizing Y ou can personalize your Services feature to provide quicker access to your most used or favorite information.
SYNC AppLink™ Note: This feature is only available in the United States. Note: Y our smartphone must be paired and connected to SYNC to access AppLink. Note: iPhone users need to connect the phone to the USB port in order to start the application. It is recommended to lock your iPhone after starting an application.
T o Access Using V oice Commands 1. Press the voice icon. 2. When prompted, say “Mobile Apps”. 3. Say the name of the application after the tone. 4. The app should start. While an app is running through SYNC, you can press the voice button and speak commands specific to the app, such as “Play Station Quickmix”.
6. Press OK and scroll through selections of: • Play All • Artists • Albums • Genres • Playlists • T racks • Explore USB • Similar Music • Return When the desired selection appears in the display , press OK to build your desired music selection.
“USB” “Play track <name>” 1,3 “Refine album <name>” 1,3 “Refine artist <name>” 1,3 “Refine song <name>” 1,3 “Refine track <name>” 1,3 “Repeat of.
V oice command guide “Autoplay” T urn on to listen to music which has already been randomly indexed during the indexing process. T urn off and the system does not begin to play any of your music until all media has all been indexed. Indexing times can vary from device to device and also with regard to the number of songs being indexed.
Press the voice icon and when prompted say “Bluetooth Audio” and then any of the following: “BLUETOOTH AUDIO” “(Phone) (Media) (Bluetooth) Connections” “Pause” “Play” “Play next .
When you select: Y ou can: Select Source SYNC USB: Press OK to access music plugged into your USB port. Y ou can also plug in devices to charge them (if supported by your device). Once connected, the system indexes any readable media files. (The time required to complete this depends on the size of the media content being indexed.
When you select: Y ou can: Media Settings Choose to shuffle or repeat your music and select your Autoplay settings. Once these selections are turned on, they remain on until turned off. Press SEEK to play the previous or next track. Note: Some digital media players require both USB and line in ports to stream data and music separately .
If there are no media files to access, the display indicates there is no media. If there are media files, you have the following options to scroll through and select from: When you select: Y ou can: Play All Play all indexed media (tracks) from your playing device in flat file mode, one at a time in numerical order .
When you select: Y ou can: Genres Sort indexed music by genre (category) type. SYNC lists the genres alphabetically in flat file mode. If there are more than 255, SYNC automatically organizes them into alphabetical categories. Press OK to select and then scroll to select the desired genre and press OK.
When you select: Y ou can: Similar Music Play music similar to what is currently playing from the USB port. The system uses the metadata information of each song to compile a playlist for you. Press OK to select. The system creates a new list of similar songs and begins playing.
Bluetooth Devices Menu Options This menu allows you to add, connect and delete devices as well as turn Bluetooth on and off. 1. Press AUX and then MENU to enter the Media Menu. 2. Scroll until System Settings appears and select OK. 3. Scroll until Bluetooth Devices appears.
Advanced Menu Options This menu allows you to access settings such as prompts, language, performing a master reset as well as returning to factory defaults. 1. Press AUX and then MENU to access the Media Menu. 2. Scroll until System Settings appears and select OK.
When you select: Y ou can: Master Reset Completely erase all information stored on SYNC (all phonebook, call history , text messages and all paired devices) and return to the factory default settings. Application Download new software applications (if available) and then load the desired applications through your USB port.
Phone issues Issue Possible cause(s) Possible solution(s) SYNC is not able to download my phonebook. • T h i si sa phone-dependent feature, OR • Possible phone malfunction.
Phone issues Issue Possible cause(s) Possible solution(s) I am having trouble connecting my phone to SYNC. • T h i si sa phone-dependent feature, OR • Possible phone malfunction.
USB and media issues Issue Possible cause(s) Possible solution(s) I am having trouble connecting my device. Possible device malfunction. • T ry turning off the device, resetting the device or removing the device’ s battery , then trying again. • Make sure you are using the manufacturer’ s cable.
V ehicle Health Report and SYNC Services (T raffic, Directions and Information) issues Issue Possible cause(s) Possible solution(s) I received a text that the V ehicle Health Report is not activated. • Y our account may not be activated on the website, OR • Y ou may have the wrong VIN (vehicle identification number) listed.
V oice command issues Issue Possible cause(s) Possible solution(s) SYNC does not understand what I am saying. • Y ou may be using the wrong voice commands, OR • Y ou may be speaking too soon or at the wrong time. • Review the Phone voice commands and the Media voice commands at the beginning of their respective sections.
V oice command issues Issue Possible cause(s) Possible solution(s) SYNC does not understand or is calling the wrong contact when I want to make a call.
INTRODUCTION W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
Note: Some features are not available while your vehicle is moving. Note: Y our system is equipped with a feature that allows you to access and control audio features for 30 minutes after you switch the ignition off (and no doors open).
SETTINGS Press to select any of the following: • Clock • Display • Sound • V ehicle • Settings • Help HOME Press to access your home screen. Depending on your vehicle’ s option package and software, your screens may vary in appearance from the descriptions in this section.
Using the T ouch-sensitive Controls on Y our System T o turn a feature on and off, just touch the graphic with your finger . T o get the best performance from the touch-sensitive controls: • Do not press hard on the controls. They are sensitive to light touch.
Safety information W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. Y our primary responsibility is the safe operation of the vehicle.
See the following chart for more specific examples: Restricted Features Cellular Phone Pairing a Bluetooth phone Adding phonebook contacts or uploading phonebook contacts (from a USB) List entries are.
The cellular profile, media device index, and development log will remain in the vehicle unless you delete it and are generally accessible only in the vehicle when the cellular phone or media player is connected. If you no longer plan to use SYNC® or the vehicle, we recommend you perform a Master Reset to erase all information stored in SYNC®.
How to Use V oice Commands with Y our System Press the voice icon. After the tone, speak your command clearly . These commands can be said at any time.
Accessing a List of Available Commands • If you use the touchscreen, press the Settings icon > Help > V oice Command List. • If you use the steering wheel control, press the voice icon.
Confirmation Prompts: The system uses these short questions to confirm your voice request. If turned off, the system simply makes a best guess as to what you requested. The system may still occasionally ask you to confirm settings. Phone/Media Candidate Lists: Candidate lists are lists of possible results from your voice commands.
Using V oice Commands with the T ouchscreen Options Y our voice system has a dual mode feature which allows you to switch between using voice commands and making on-screen selections. This is most often available when using navigation. Buttons outlined in blue indicate selections that are part of the dual mode feature.
Some of the voice commands that are available while viewing this screen are: “STREET ADDRESS” “Enter house number” “Change house number” “Enter street name” “Change street name” .
Some of the voice commands that are available while viewing this screen are: “INTERSECTION” “Enter first street name” “Change first street name” “Enter second street name” “Change se.
F . T ouch this button to scroll down for more options, such as: • SD Card • BT Stereo • A/V In G. These buttons change with the media mode you are in. H. Radio memory presets and CD controls. Note: Some features may not be available in your area.
“BROWSE” “<League> games” ”<Sirius category> channels” “CD track list” “SD card” “Sirius channel guide” “USB” “Help” * This command is only usable if you have an active subscription to SIRIUS satellite radio.
AM and FM T ouch the AM or FM tab to listen to the radio. T o change between AM and FM presets, just touch the AM or FM tab. Memory Presets Save a station by pressing and holding one of the memory preset areas. There is a brief mute while the radio saves the station.
T AG Button is available when HD Radio is on, and allows you to tag a song to download later . When you select On, T AG appears on-screen when HD Radio is active. Y ou can touch TA G to save the information of the song that is playing. When you plug in your portable music player , the information transfers, if supported by your device.
TA G allows you to save a song to download later when you are on an acquired HD Radio station and the feature is on. T o turn the feature on and use it: 1. Press AM or FM > Options > TA G button > On. 2. When you hear a song you like, touch T AG.
HD Radio Reception and Station Troubleshooting Potential Reception Issues Reception area If you are listening to a multicast station and you are on the fringe of the reception area, the station may mute due to weak signal strength.
Potential station issues Issue Cause Action Echo, stutter , skip or repeat in audio. Increase or decrease in audio volume. This is poor time alignment by the radio broadcaster . No action required. This is a broadcast issue. Sound fading or blending in and out.
Radio V oice Commands If you are listening to the radio, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not listening to the radio, press the voice button and, after the tone, say “Radio”, then any of the commands in the following chart.
SIRIUS® Satellite Radio (If Activated) Press the lower left corner of the touchscreen, then select the SIRIUS tab. Presets Save a channel by pressing and holding one of the memory preset areas. There is a brief mute while the radio saves the channel.
Parental Lockout allows you to lock and unlock channels, change or reset your PIN or unlock all channels. T o use this feature, you need your initial PIN, which is 1234. Artist/T itle/T eam Alerts allows you to select Artists, T itles and T eams that you would like the system to alert you to when they are playing on other channels.
If you are not listening to SIRIUS satellite radio, press the voice button and, after the tone, say “Sirius”, then any of the commands in the following chart.
SIRIUS Satellite Radio Information Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes.
SIRIUS troubleshooting tips Radio display Condition Possible action Acquiring... Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly . Sat Fault/SIRIUS system failure.
SIRIUS troubleshooting tips Radio display Condition Possible action Subscription Updated. SIRIUS has updated the channels available for your vehicle. No action required. CD Press the lower left corner of the touchscreen, and then select the CD tab. Y ou can also advance and reverse the current track or current folder , if applicable.
Browse T ouch this button to look through all available CD tracks. CD V oice Commands If you are listening to a CD, press the voice button on the steering wheel control.
SD logo is a trademark of SD-3C, LLC. USB Port The ports are located either in the center console or behind a small access door in the instrument panel. T o access and play music from your device, press the lower left corner of the touchscreen, and then select the USB tab.
Note: Y our vehicle may not have all these sound settings. • Media Player Settings allows you to select more settings, which is under Media Player . See Settings. • Device Information displays software and firmware information about the currently connected media device.
“USB” or “SD CARD” “Play movie <name>” ** “Repeat one” “Play music video <name>” ** “Shuffle” “Play next song” “Shuffle off” “Play playlist <name>.
Supported Media Players, Formats and Metadata Information SYNC is capable of hosting nearly any digital media player , including iPod®, Zune™, plays from device players, and most USB drives. Supported audio formats include MP3, WMA, W A V and AAC. It is also able to organize your indexed media from your playing device by metadata tags.
A/V Inputs W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
T o use the auxiliary input jack feature, make sure that your portable music player is designed for use with headphones and that it is fully charged. Y ou also need an audio extension cable with stereo male 1/8th-inch (3.5 millimeter) connectors at one end and a RCA jack at the other .
PHONE A. Phone B. Quick Dial C. Phonebook D. History E. Messaging F . Settings Hands-free calling is one of the main features of SYNC®. Once you pair your phone, you can access many options using the touchscreen or voice commands. While the system supports a variety of features, many are dependent on your cellular phone’ s functionality .
Pairing Y our Phone for the First Time W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
Making Calls Press the voice button on your steering wheel controls. When prompted, say , “Call <name>” or say “Dial”, then the desired number . T o end the call or exit phone mode, press and hold the phone button. Receiving Calls During an incoming call, an audible tone sounds.
Certain smart phones may support transferring street addresses when listed with phone book contact information. If your phone supports this feature, you can select and use these addresses as destinations and save them as favorites.
Composing a T ext Message Note: This is a speed-dependent feature. It is unavailable when your vehicle is traveling at speeds over 3 mph (5 km/h). Note: Downloading and sending text messages using Bluetooth are phone-dependent features. 1. T ouch the top left corner of the display to access the Phone menu.
Receiving a T ext Message When a new message arrives, an audible tone sounds and the screen displays a pop-up with the caller name and ID, if supported by your phone. Y ou can press: • Vi e w to view the text message. • Listen for SYNC to read the message to you.
Internet Data Connection If your phone is compatible, use this screen to adjust your internet data connection. Select to make your connection profile with the personal area network or to turn off your connection. Y ou can also choose to adjust your settings or have the system always connect, never connect when roaming or query on connect.
“MESSAGES” “Call” “Forward text messages” “Listen to text message <#>” “Listen to text messages” “Reply to text messages” “Help” INFORMA TION If your vehicle is equipped with Navigation, touch the i (Information) button to access these features.
SYNC Services (If Equipped, United States Only) Note: SYNC Services requires activation before use. Visit www .SYNCMyRide.com to register and check your eligibility for complimentary services. Standard phone and message rates may apply . Subscription may be required.
Connecting to SYNC Services Using V oice Commands Press the voice button on the steering wheel controls. 1. When prompted, say “Services”. This initiates an outgoing call to SYNC Services using your paired and connected Bluetooth-enabled cellular phone.
Receiving Turn-by-T urn Directions 1. When connected to SYNC Services, say “Directions” or “Business Search”. T o find the closest business or type of business to your current location, just say “Business Search” and then “Search Near Me”.
Disconnecting from SYNC Services 1. Press and hold the phone button on the steering wheel. 2. Say “Good-bye” from the SYNC Services main menu. SYNC Services quick tips Personalizing Y ou can personalize your Services feature to provide quicker access to your most used or favorite information.
“SER VICES” “Services” “Update route” “Help” SIRIUS T ravel Link (If Equipped and If Activated) W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road.
Traf fic On Route and Traf fic Nearby T ouch these buttons to identify traffic incidents on your route, nearby your vehicle’ s current location or near any of your favorite places, if programmed. Fuel Prices T ouch this button to view fuel prices at stations close to your vehicle’ s location or on an active navigation route.
* If you have said, “Sports headlines”, “Sports schedule” or “Sports scores”, you may say any of the commands in the “Sports headlines, Sports schedules and Sports scores” commands cha.
Alerts If your vehicle is equipped with Navigation, touch the i (Information) button to access these features. If your vehicle is not equipped with Navigation, touch the corner of the touchscreen with the green tab. Press Alerts, and then choose from any of the following services: • Vi e w the message.
W ARNING: Always place your phone in a secure location in your vehicle so it does not become a projectile or damaged in a crash. Failure to do so may cause serious injury to someone or damage the phone, which could prevent 911 Assist from working properly .
T o Make Sure that 91 1 Assist W orks Properly • SYNC must be powered and working properly at the time of the incident and throughout feature activation and use. • The 911 Assist feature must be set on before the incident. • Y ou must pair and connect a Bluetooth-enabled and compatible phone to SYNC.
91 1 Assist Privacy Notice When you turn on 911 Assist, it may disclose to emergency services that your vehicle has been in a crash involving the deployment of an airbag or activation of the fuel pump shut-off.
The system allows you to check your vehicle’ s overall health in the form of a diagnostic report card. The V ehicle Health Report contains valuable information, such as: • V ehicle Diagnostic Info.
SETTINGS A. Clock B. Display C. Sound D. V ehicle E. Settings F . Help Under this menu, you can set your clock, access and adjust the display , sound and vehicle settings as well as access settings for specific modes or the help feature. Clock Note: Y ou cannot manually set the date.
Y ou can also turn the outside air temperature display on and off. It appears at the top center of the touchscreen, next to the time and date. The system automatically saves any updates you make to the settings.
Sound Press the Settings icon > Sound, then select from the following: Sound Settings Bass DSP * Midrange Occupancy Mode * T reble Speed Compensated V olume Set Balance and Fade * If equipped.
V ehicle Health Report T urn Automatic Reminders on and off and set the mileage interval at which you would like to receive the reports. Press ? for more information on these selections. When done making your selections, press Run V ehicle Health Report Now if you want your report.
System Press the Settings icon > Settings > System, then select from the following: System Language Select to have the touchscreen display in English, Spanish or French. Distance Select to display units in kilometers or miles. T emperature Select to display units in Celsius or Fahrenheit.
V oice Control Press the Settings icon > Settings > V oice Control, then select from the following: V oice control Interaction Mode Standard interaction mode provides more detailed interaction and guidance. Advanced mode has less audible interaction and more tone prompts.
Media Player Press the Settings icon > Settings > Media Player , then select from the following: Media player Autoplay When this feature is on, the system automatically switches to the media source upon initial connection. This allows you to listen to music during the indexing process.
Navigation Press the Settings icon > Settings > Navigation, then select from the following: Navigation Map Preferences T urn breadcrumbs on and off. Have the system display your turn list top to bottom or bottom to top. T urn the Parking POI notification on and off.
Phone Settings Press the Settings icon > Settings > Phone, then select from the following: Phone Bluetooth Devices Connect, disconnect, add or delete a device, as well as save it as a favorite. Bluetooth T urn Bluetooth on and off. Do Not Disturb Have all calls go directly to your voice mail and not ring inside your vehicle.
Wireless & Internet Y our system has a Wi-Fi feature that creates a wireless network within your vehicle, thereby allowing other devices (such as personal computers or phones) in your vehicle to speak to each other , share files or play games.
W ireless & Internet USB Mobile Broadband Instead of using W i-Fi, your system can also use a USB mobile broadband connection to access the internet. (Y ou must turn on your mobile broadband device on your personal computer before connecting it to the system.
Help Press the Settings icon > Help, then select from the following: Help Where Am I? View your vehicle’ s current location, if your vehicle is equipped with navigation. If your vehicle is not equipped with navigation, nothing displays. System Information T ouchscreen system serial number .
CLIMA TE Press the lower right corner on the touchscreen to access your climate control features. Depending on your vehicle line and option package, your climate screen may look different from the screen shown here. A. Power: T ouch to switch the system off and on.
E. MAX A/C: T ouch to cool your vehicle with recirculated air . T ouch again for normal A/C operation. MAX A/C: • Distributes air through instrument panel vents. • Is more economical and efficient than normal A/C mode. • May help reduce odors from entering your vehicle.
Climate Control V oice Commands The following voice commands are available at the main menu level of a voice session. For example, press the voice button and after the prompt, “Say a command”; say.
“TEMPERA TURE” “High” “Low” “<15.5–29.5> degrees” “<60–85> degrees” “Help” NA VIGA TION SYSTEM (IF EQUIPPED) Note: The navigation SD card must be in the SD card slot to operate the navigation system. If you need a replacement SD card, see your authorized dealer .
1. Enter the necessary information into the highlighted text fields (in any order). For address destination entry , Go! appears once you enter all the necessary information. Pressing Go! makes the address location appear on the map. If you choose Previous Destination, the last 20 destinations you have selected appear .
Point of Interest (POI) Categories Y our system offers a variety of points of interest categories. Main categories Food/Drink & Dining Automotive T ravel & T ransportation Shopping Financial E.
cityseekr (If Available) Note: cityseekr point of interest information is limited to approximately 154 cities (132 in the United States, 13 in Canada and 9 in Mexico). cityseekr , when available, is a service that provides more information about certain points of interest such as restaurants, hotels and attractions.
Attraction This icon appears when your selection exists in multiple categories within the system. When you are viewing more information for hotels, cityseekr also tells you if the hotel has certain services and facilities using icons.
Setting Y our Navigation Preferences Select settings for the system to take into account when planning your route. Press the Settings icon > Settings > Navigation. When you select: Y ou can: Map Preferences T urn breadcrumbs on and off. Have the system display your turn list top to bottom or bottom to top.
When you select: Y ou can: T raffic Preferences Choose how you want the system to handle traffic problems along your route. Automatic: Have the system reroute you to avoid traffic incidents that develop and impact the current route (no notification is provided).
Change the appearance of the map display by repeatedly pressing the arrow button in the upper left corner of the screen. It toggles between three different map modes: Heading up, North up, and 3D. Heading up (2D map) always shows the direction of forward travel to be upward on the screen.
Map Icons V ehicle mark shows the current location of your vehicle. It stays in the center of the map display , except when in scroll mode. Scroll cursor allows you to scroll the map; the fixed icon is in the center of the screen. The map position closest to the cursor is in a window on the top center part of the screen.
Quick-touch Buttons When in map mode, touch anywhere on the map display to access the following options: When you select: Y ou can: Set as Dest Select a scrolled location on the map as your destination. (Y ou may scroll the map by pressing your index finger on the map display .
Navigation V oice Commands When in navigation mode, press the voice button on the steering wheel control. After the tone, say any of the following commands: Navigation system voice commands “Cancel .
“DESTINA TION” “Nearest <POI category>” “Nearest POI” “Play nametags” “POI category” “Previous destination” “Street address” “Help” “NA VIGA TION” “Destinat.
GENERAL INFORMA TION SYNC® End User License Agreement (EULA) • Y ou have acquired a device (“DEVICE”) that includes software licensed by Ford Motor Company and its affiliates (“FORD MOTOR COMP ANY”) from an affiliate of Microsoft Corporation (“MS”).
DESCRIPTION OF OTHER RIGHTS AND LIMIT A TIONS: • Speech Recognition: If the SOFTW ARE includes speech recognition component(s), you should understand that speech recognition is an inherently statistical process and that recognition errors are inherent in the process.
• Security Updates/Digital Rights Management: Content owners use the WMDRM technology included in your DEVICE to protect their intellectual property , included copyrighted content. Portions of the SOFTW ARE on your DEVICE use WMDRM software to access WMDRM-protected content.
If FORD MOTOR COMP ANY or third party software and services suppliers provide or make available to you Supplemental Components and no other EULA terms are provided along with the Supplemental Components, then the terms of this EULA shall apply .
INTELLECTUAL PROPER TY RIGHTS: All title and intellectual property rights in and to the SOFTW ARE (including but not limited to any images, photographs, animations, video, audio, music, text and “ap.
No Liability for Certain Damages: EXCEPT AS PROHIBITED BY LA W , FORD MOTOR COMP ANY , ANY THIRD P ARTY SOFTW ARE OR SERVICES SUPPLIERS, MS, MICROSOFT CORPORA TION AND THEIR AFFILIA TES SHALL HA VE NO.
Keep User’ s Guide in V ehicle When kept in the vehicle, the User’ s Guide will be a ready reference for you and other users unfamiliar with the W indows Automotive-based system.
Navigation Features Any navigation features included in the system are intended to provide turn by turn instructions to get you to a desired destination. Please make certain all persons using this system carefully read and follow instructions and safety information fully .
T eleNav Software End User License Agreement Please read these terms and conditions carefully before you use the T eleNav Software. Y our use of the T eleNav Software indicates that you accept these terms and conditions.
3. Software License Subject to your compliance with the terms of this Agreement, T eleNav hereby grants to you a personal, non-exclusive, non-transferable license (except as expressly permitted below .
or functionality of the T eleNav Software are not intended to support such high risk applications, especially in more remote geographical areas. TELENA V EXPRESSL Y DISCLAIMS AND EXCLUDES ALL W ARRANT.
6. Arbitration and Governing Law Y ou agree that any dispute, claim or controversy arising out of or relating to this Agreement or the T eleNav Software shall be settled by independent arbitration involving a neutral arbitrator and administered by the American Arbitration Association in the County of Santa Clara, California.
8.3 By using the T eleNav Software, you consent to receive from T eleNav all communications, including notices, agreements, legally required disclosures or other information in connection with the T eleNav Software (collectively , “Notices”) electronically .
NavT eq End User License Agreement END USER TERMS The content provided (“Data”) is licensed, not sold. By opening this package, or installing, copying, or otherwise using the Data, you agree to be bound by the terms of this agreement.
License Limitations on T ransfer: Y our limited license does not allow transfer or resale of the Data, except on the condition that you may transfer the Data and all accompanying materials on a perman.
Disclaimer of Liability: NT AND ITS LICENSORS (INCLUDING THEIR LICENSORS AND SUPPLIERS) SHALL NOT BE LIABLE TO YOU IN RESPECT OF ANY CLAIM, DEMAND OR ACTION, IRRESPECTIVE OF THE NA TURE OF THE CAUSE O.
Government End Users: If the Data is being acquired by or on behalf of the United States government or any other entity seeking or applying rights similar to those customarily claimed by the United States government, this Data is a “commercial item” as that term is defined at 48 C.
Gracenote® End User License Agreement (EULA) This device contains software from Gracenote, Inc. of 2000 Powell Street Emeryville, California 94608 (“Gracenote”).
EXPRESS OR IMPLIED, REGARDING THE ACCURACY OF ANY GRACENOTE DA T A FROM THE GRACENOTE SERVERS OR GRACENOTE CONTENT . GRACENOTE COLLECTIVEL Y AND SEP ARA TEL Y RESERVE THE RIGHT TO DELETE DA T A AND/OR.
911 Assist™ ...................... 455, 533 A ABS (see Brakes) ..................... 235 Accessing and using your USB port ....................................511 Accessing call history/phone book during active call .............444 Accessing your calendar .
B Battery ....................................... 334 acid, treating emergencies ..... 334 jumping a disabled battery .... 297 maintenance-free ....................334 replacement, specifications ... 405 servicing .................................. 334 Bed extender .
Utilizing the Mediation/Arbitration Program ................................... 304 D Defrost .......................153, 155, 157 rear window ............................161 Dipstick automatic transmission fluid ......................................
G Garage door opener .......... 180, 185 Gas cap (see Fuel cap) ............205 Gauges ....................................... 106 H Hazard flashers ......................... 296 HD Radio™ ............................... 500 Headlamps ..............
Loading instructions .................258 Load limits ................................. 252 Locks autolock .....................................77 childproof .................................. 37 doors .......................................... 76 Lubricant specifications .
Power distribution box (see Fuses) ....................... 309, 314 Power door locks ........................ 76 Power mirrors ........................... 100 Powerpoint ................................190 Power steering .......................... 250 fluid, checking and adding .
Seat belts (see Safety restraints) .................................... 40 Seats child safety seats ................ 20, 25 cleaning ................................... 357 climate control ........................ 178 filter ..........................
T ires ........................... 365–366, 387 alignment ................................ 379 care .......................................... 365 changing .......................... 387, 390 checking the pressure ............ 375 inflating ........
デバイスFord F-150 (2013)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ford F-150 (2013)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFord F-150 (2013)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ford F-150 (2013)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ford F-150 (2013)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ford F-150 (2013)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFord F-150 (2013)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ford F-150 (2013)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFord F-150 (2013)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
