A&Dメーカー1WMPD4002313の使用説明書/サービス説明書
ページ先へ移動 of 24
Weighing Indicator for Check Weighing Scales 1WMPD4002313.
This Manual and Marks All safety messages are identified by the following, “W ARNI NG” or “CAUTION”, of ANSI Z535.4 (American National S tandar d Institute: Product Safety Signs and Labels). The meanings are as follows: WA R N I N G A potentially hazardous situatio n which, if not avoided, could result in death or serious injury .
1 Content s 1. COMPLI ANCE ................................................................................................. 2 2. INTRO DUCTION .............................................................................................. 3 3. UNP ACKING .
2 1. COMPLIANCE Compliance with FCC rules Please note that this equipment generat es, uses and can radiate radio frequency energy . This equipment has been tested and has been found to comply with the limits of a Class A computing de vice pursuant to Subpart J of Part 15 of FCC rules.
3 2. INTRODUCTION This manual describes how this product wor ks and how to get the most out of it in terms of performance. The FS - D weighing indicator is used to bu ild high performance check weighing scales. It has similar specifications and functions as an indicator of the FS - i series.
4 3. UNP ACKING Unpack the indicator carefully and keep the p acking material if you are likely to transport the indicator again in the future. When unpacking, check whether all of the following items.
5 4. INST ALLA TION and PRECAUTIONS 4-1. Precautions for Installing the Indicator Ground the indicator so that the user will not be subjected an electric shock. Do not handle the main power cord with wet hands. The AC plug is not water-resist ant.
6 Setscrew B Setscrew A 4. Solder the wires to the pin contact s of the connector . A 5 m or less load cell cable is recommended as the FS - D uses a 4 wire system (no remote sensing). 5. Reassemble the connector plug and tighten the setscrew A. 6.
7 4-4. Setting Up the Indicator Connect the main power cord to an outlet that has an earth ground terminal. Y ou may use the earth terminal on the rear si de of the display to ground the indicator . If necessary , adjust the viewing angle of the display by loosening the 2 clamps, changing the angle and re-tightening the clamps.
8 5. NAMES AND FUNCTIONS No. NAMES FUNCTIONS / OPERA TION WEIGHT DA T A DISPLA Y Indicates the weight data. WEIGHING UNIT INDICA T OR Indicates the weighing unit in use. ANALOG WEIGHT DISPLA Y Indicates zero to full scale or comparison limit s and results.
9 No. NAMES FUNCTIONS / OPERA TION COMP ARISON INDICA T ORS Indicates the results of the weight comparison LO (RED), OK (GREEN) and HI (YELLOW). ST ABLE ANNUNCIA TOR T urns ON when the weight reading is ST ABLE. ZERO ANNUNCIA TOR T urns ON when the weight is in the center of ZERO range.
10 6. FUNCTION P ARAMETER SETTINGS T o design a platform scale, se t the cap acity , weighing unit and other functions according to the specifications of the scale. Normally , end users do not have to set these function parameters and these setting can be sealed together with the calibration switch.
11 6-2. Function list Item Function number Description C01- 0 CAL switch enabled, 0 key enabled C01- 1 CAL switch disabled, 0 key disabled Calibration C01- 2 CAL switch enabled, 0 key disabled Do .
12 7. CALIBRA TION This function adjusts the scale (i ndicator) for accurate weighing. Calibration must be done when the FS - D is initially connected to a load cell (base unit). Calibration may also be required acco rding the changes in the environment.
13 If you need ZERO calibration but do not need SP AN calibration, turn the power off to exit from the calibration procedure. 7. T o calibrate with a different weight, change the displayed value using the 10-key pad. If you en ter the wrong number , press the C key .
14 8. AUT O-T ARE FUNCTION The FS - D has an auto-tare function to be used with the comp arator function enabled. If the weight value is within the OK r ange and stable for a preset time, then the indicator will automatically tare the weight and show zero.
15 9. ADDITIONAL INFORMA T ION This section describes the additional functions and corrections to the instruction manual of FS - i series (WM+PD4001332 and 1WMPD4001368) which are common to the FS - D. 9-1. F-Function list The following function settings are added (“ 1 1-2.
16 The frame ground and the shie ld are connected internally and there is no difference between them in use. Data form at Example of data Out of range “kg” (+) O L , +99999 9 9 9 _ k g C R L F Out of range “kg” (+) O L , +9999 . 9 9 9 _ k g C R L F The position of decimal point is diffe rent according to the model and/or “ f02 ”.
17 Command H I , + 0 0 1 0 0 C R L F A s su m e 2 d e cimal place number . Reply H I , + 0 0 1 0 0 C R L F 1.00% will be set as LO limit %. Command L O , + 0 0 1 0 0 C R L F A s su m e 2 d e cimal place number . Reply L O , + 0 0 1 0 0 C R L F 1.00% will be set as LO limit %.
18 10. ERROR MESSAGES Overload error W arning to indicate that an object beyond the weighing capacity has been placed on the weighing p an. Remov e the object from the weighing pan. Power-on error W arning to indicate that an object beyond the power-on zero range (50% of the weighing capacity or 10%) i s placed on the weighing platfo rm.
19 1 1. SPECIFICA TIONS 1 1-1. Capacity and minimum display C02 - setting 0 * 1 2 3 4 5 6 7 Capacity 6 15 30 60 150 300 600 1500 0.002 * 0.005 0.01 0.02 0.05 0.1 0.2 0.5 0.001 0.002 0.005 0.01 0.02 0.05 0.1 0.2 kg Min. display 0.0005 0.001 0.002 0.005 0.
20 1 1-3. Options OP - 02 (HC - 02 i ) SLA Battery (Y uasa Battery NP4-6 recommended.) OP - 03 (FS - 03 i ) RS - 232C + Comp arator Rela y Output (See note.) OP - 04 (FS - 04 i ) RS - 422/485 + Comp arator Re lay Output (See note.) Note OP - 03 and OP - 04 cannot coexist.
.
3-23-14 Higashi-Ikebukuro, Toshima-ku, Tokyo 170-0013 JAPAN Telephone: [81] (3) 5391-6132 Fax: [81] (3) 5391-6148 A&D ENGINEERING, INC. 1756 Automation Parkway, San Jose, California 95 131 U.
デバイスA&D 1WMPD4002313の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
A&D 1WMPD4002313をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはA&D 1WMPD4002313の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。A&D 1WMPD4002313の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。A&D 1WMPD4002313で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
A&D 1WMPD4002313を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はA&D 1WMPD4002313の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、A&D 1WMPD4002313に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちA&D 1WMPD4002313デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
