AlpineメーカーSPX-Z18Tの使用説明書/サービス説明書
ページ先へ移動 of 48
.
.
1 English/Français Points to Observe for Safe Usage • Read this manual carefully bef ore star ting operation and use this system safely . We cannot be responsible f or problems resulting from f ailure to observe the instructions in this manual.
2 Contents / Contenu Installation / Installation P ar ts List / Liste des pi è ces ................................................................................... 3 W oof er Installation / Installation du Woof er .................................
3 English/Fran ç ais English 1 Main Unit 2 Grille Ring 3 Grille 4 Adapter Ring 5 Screw M4 x 12 6 Screw ø 4 x 19 1 Unit é principale 2 Bague de la grille 3 Grille 5 Vis M4 x 12 6 Vis ø 4 x 19 7 Cl .
4 Woofer Installation / Installation du W oofer Speaker Wire Connections / Raccordement des fils d ’ enceinte 1. Insert the speaker wires through the connection holes. / Ins é rer les fils d ’ enceinte dans les trous de raccordement. 2. F asten with a hexagonal wrench.
5 English/Fran ç ais X3 q X3 q Midrange Installation / Installation du haut-parleur m é dial Installation without a grille / Installation sans grille Installation with a grille / Installation avec grille Speaker Wire Connections / Raccordement des fils d ’ enceinte 1.
6 T weeter Installation / Installation du T weeter Installation with springs / Installation avec ressorts Installation with a mounting cup (Installation from the front)/ Installation with fastening ri.
7 English/Fran ç ais X3 g Network Installation / Installation du circuit Note /Remarque: Do not install the Crossov er network where it will be exposed to moisture such as under the floor mat or near the air conditioner . This may cause a malfunction.
8 Network connections / Connexions du circuit Caution Connection Example 1 / Exemple de connexion 1 When connecting to single amp/single wiring / Lors du raccordement a vec un seul amplificateur/ c â blage simple .
9 English Crossover Network Introduction It is common knowledge that the automotiv e inter ior is one of the most inhospitable environments f or high-fidelity sound, and that ev er y vehicle poses its own unique set of installation and acoustic challenges.
10 Jumper Group Function Although recommendations are made f or the most common system types in the following pages, there are actually o ver 1000 unique and useful jumper combinations a vailable f or a wide variety of v ehicles, installations and personal tastes .
11 English R6 = 1.0 Ω R7 = 1.0 Ω R8 = 22 Ω C3 = 18 µ F C4 = 33 µ F C5 = 10 µ F L3 = 0.32mH L4 = 2.0mH L5 = 2.9mH MID HP/LP: As a selectable bandpass filter f or the midrange, the net eff ect of this section is naturally linked to the selections made in the tw eeter high-pass and woof er low-pass sections .
12 WF-LP: While functioning as a low-pass filter f or the woofer , this section also provides a wide degree of adjustments f or optimizing performance and system integration.
13 English System T ype 1 • T ype-1B is f or such cases where pathlength is nearly the same to all drivers , but where the mount- ing surf ace orientation creates a unif or m but f air ly e xtreme off-axis listening angle.
14 System T ype 1 10 0 – 10 – 20 – 30 – 40 – 50 20Hz 30Hz 100Hz 1.0KHz 3.0KHz 10KHz 30KHz 300Hz T ype-1A: P athlength to the listening posi- tion is considered to be basically equal in this case (ideally 2-3m aw ay), with relativ e on-axis positioning of all drivers .
15 English 10 0 – 10 – 20 – 30 – 40 – 50 20Hz 30Hz 100Hz 1.0KHz 3.0KHz 10KHz 30KHz 300Hz T ype-1B: While the mounting configuration is the same as T ype-1A, this network set- ting provides a v ar iation for when personal taste, positioning or v ehicle acoustics neces- sitates more high frequency output from the midrange and tweeter .
16 System T ype 2 • T ype-2A takes into account that all drivers are mounted more or less flush to the panel on a mostly flat v er tical surf ace such as the door , thus present- ing varying degrees of both axis and distance of each driver to the listener .
17 English 10 0 – 10 – 20 – 30 – 40 – 50 20Hz 30Hz 100Hz 1.0KHz 3.0KHz 10KHz 30KHz 300Hz T ype-2A: For the tweeter in this case , pathlength from the listening position is con- sidered to be 85cm, at appro ximately 15- 20 ° off-axis.
18 10 0 – 10 – 20 – 30 – 40 – 50 20Hz 30Hz 100Hz 1.0KHz 3.0KHz 10KHz 30KHz 300Hz T ype-2B: T weeter and midrange positioning are the same as in T ype-2A, but the woof er is located f ar ther forw ard. This results in a more e xtreme woof er listening angle of ap- pro ximately 70 ° , with a delay of 28cm rela- tiv e to the mid.
19 English System T ype 3 • T ype-3A assumes that both the midrange and tweeter are mounted close together in the same plane, and theref ore relatively on-axis and equidistant to the listener . • T ype-3B takes into consideration that the tweeter and midrange are mounted basically flush to the panel with little or no build out.
20 10 0 – 10 – 20 – 30 – 40 – 50 20Hz 30Hz 100Hz 1.0KHz 3.0KHz 10KHz 30KHz 300Hz HP-2 HP-1 LP-2 LP-1 +2dB MID HP/LP – 3dB – 1.5dB 0dB/0 ° +1.
21 English T ype-3B: Despite the fact that the midrange and tweeter are mounted in the same plane and in close proximity , their orientation re- sults in the acoustic center of the midrange being farther awa y . Therefore, the midr ange is considered to be 8.
22 System T ype 4 System Description In this system type, some le vel of e xter nal signal processing is av ailable, allo wing use of the network in a par tially active mode . Although speakers ma y be mounted in a wide variety locations in this case, it is recommended that tr aditional techniques be used regarding both positioning and placement.
23 English Network Jumper Setting HP-2 HP-1 LP-2 LP-1 +2dB MID HP/LP – 3dB – 1.5dB 0dB/0 ° +1.5dB/15 ° +4dB/30 ° HP-1 HP-2 HP-3 BYP ASS BYP ASS LP-1 LP-2 LP-3 LP-BYP ASS HP-BYP ASS TW LEVEL WF .
24.
25 Français Introduction au circuit répartiteur T out le monde sait que l’intérieur d’une voiture n’est pas l’en vironnement le plus hospitalier pour le son haute fidélité, et que chaque véhicule possède ses propres défis d’installation et d’acoustique.
26 TW LEVEL: En g é n é ral, cette section permet un r é glage de niveau pr é cis pour un r é sultat optimal ou le respect de go û ts personnels.
27 Fran ç ais R6 = 1,0 Ω R7 = 1,0 Ω R8 = 22 Ω C3 = 18 µ F C4 = 33 µ F C5 = 10 µ F L3 = 0,32mH L4 = 2,0mH L5 = 2,9mH HP-2 HP BYP ASS LP BYP ASS +2dB L4 L5 C3 R6 L3 C4 R7 R8 C5 HP-1 LP-2 LP-1 .
28 WF-LP: Lorsqu ’ elle f onctionne comme un filtre passe-bas pour le woofer , cette section offre é galement un grand deg r é de r é glages pour l ’ optimisation des perf or mances et de l ’ int é gration du syst è me .
29 Fran ç ais T ype de syst è me 1 • T ype-1A est le r é glage par d é f aut du circuit, et compor te essentiellement un positionnement dans l ’ ax e principal av ec une longueur de chemin é gale de tous les amplificateurs à la position d ’é coute.
30 T ype-1A : La longueur de chemin jusqu ’à la position d ’é coute est suppos é e à peu pr è s identique dans ce cas (2-3 m id é alement), av ec un positionnement dans l ’ axe de tous les amplificateurs.
31 Fran ç ais T ype-1B : T andis que la configuration de montage est la m ê me que pour le T ype-1A, ce type de circuit fournit une variation pour les cas o ù les go û ts personnels, la position ou l ’ acoustique du v é hicule n é cessitent une plus grande sortie haute fr é quence depuis le haut-parleur m é dial et le tweeter .
32 T ype de syst è me 2 • T ype-2A suppose que tous les amplificateurs sont mont é s au m ê me niv eau que le tableau de bord sur une surf ace essentiellement plane et v er ticale telle que la por te, ce qui implique diff é rents degr é s à la f ois d ’ axe et de distance entre chaque amplifica- teur et la personne qui é coute.
33 Fran ç ais T ype-2A : Dans ce cas, pour le tweeter , la longueur du chemin depuis la position d ’é coute est de 85cm, à environ 15-20 ° en dehors de l ’ axe principal.
34 T ype-2B : La position du tweeter et du haut- parleur m é dial est la m ê me que dans le T ype-2A, mais le woof er est situ é plus loin vers l ’ av ant. Cela entra î ne un angle d ’é coute du woof er plus extr ê me d ’ environ 70 ° , av ec un retard de 28cm par rapport au haut- parleur m é dial.
35 Fran ç ais Description du syst è me Bien que le haut-parleur m é dial et le tweeter soient mont é s proches l ’ un de l ’ autre dans ce cas, les contraintes d ’ espace, l ’ esth é tique et l ’ aspect pratique requi è rent que le w oofer soit mont é s é par é ment.
36 T ype de syst è me 3 T ype-3A : Le haut-parleur m é dial et le tweeter sont à la m ê me distance et au m ê me angle tandis que le woofer est situ é plus pr è s et assez en dehors de l ’ axe de la position d ’é coute.
37 Fran ç ais T ype-3B : Malgr é le f ait que le haut-parleur m é dial et le tweeter soient mont é s sur le m ê me plan et à proximit é l ’ un de l ’ autre, leur orientation fait que le centre acoustique du haut-parleur m é dial est plus loin.
38 T ype de syst è me 4 Description du syst è me Dans ce type de syst è me, un certain niveau de traitement de signal e xter ne est dispo- nible , ce qui per met l ’ utilisation du circuit d ’ une mani è re par tiellement active.
39 Fran ç ais R é glage du cavalier du circuit HP-2 HP-1 LP-2 LP-1 +2dB MID HP/LP – 3dB – 1.5dB 0dB/0 ° +1.5dB/15 ° +4dB/30 ° HP-1 HP-2 HP-3 BYP ASS BYP ASS LP-1 LP-2 LP-3 LP-BYP ASS HP-BYP A.
40 3-120 ° 93(3.661") 67(2.637") 45.4(1.787") 8.1(0.318") 115.1(4.531") 16.8(0.661" ) φ 4.2(0.165") 124.9(4.917") φ 103.2(4.062") 5-72 ° 192.7(7.586") 25(0.984" ) φ 5.3(0.208") φ 170(6.
41 Fran ç ais 78(3.07") 30.7(1.208") 5.3(0.208") 90(3.543") 31(1.22") 13.75(0.543") 85(3.346") 76(2.991") 25.1(0.
42 Specifications / Sp é cifications System T ype Component 3- wa y speaker P ower Handling (peak/RMS) 200/50W Impedance 4 Ω F requency Response 35-60 kHz Net W eight 11 kg Drivers W oofer Midrange Sealed box Recommended V olume (Butterwor th) 0.8 ltr .
43 Français Memo/Mémo English / Français.
44 Memo/M é mo.
.
R ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, T okyo 141-0031, J apan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, T orrance, Calif ornia 90501, U.S .A. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC.
デバイスAlpine SPX-Z18Tの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Alpine SPX-Z18Tをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAlpine SPX-Z18Tの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Alpine SPX-Z18Tの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Alpine SPX-Z18Tで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Alpine SPX-Z18Tを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAlpine SPX-Z18Tの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Alpine SPX-Z18Tに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAlpine SPX-Z18Tデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。