FujitsuメーカーAOU12CQの使用説明書/サービス説明書
ページ先へ移動 of 18
A S U 9 C Q A S U 1 2 C Q A O U 9 C Q A O U 1 2 C Q.
En-2 Fig. 1 Indoor Unit 1 Operating Control Panel (Fig. 2) 2 AIR CLEANER RESET / MANUAL AUTO button ● Intake grill opening mechanism. When the remote control is not available for use, this button can be used as a Quick-start button. However when the Air Cleaning check function (see page 13) is in operation, this button is used as a reset button.
En-3 FEA TURES AND FUNCTIONS SLEEP TIMER When SLEEP is selected be pressing TIMER button during Heating mode, the air conditioner’ s thermostat setting is gradually lowered during the period of operation; during Cooling or Dry mode, the thermostat setting is gradually raised during the period of operation.
En-4 PREP ARA TION CAUTION! ● T ake care to prevent infants from accidentally swallowing batteries. ● When not using the remote control unit for an extended period, remove the batteries to avoid possible leakage and damage to the unit.
En-5 T o Select Mode Operation 1 Press the ST ART / STOP button (Fig.6 M ). The indoor unit’ s OPERA TION indicator lamp (red) (Fig. 3 5 ) will light. The air conditioner will start operating. 2 Press the MASTER CONTROL button (Fig.6 H ) to se- lect the desired mode.
En-6 OPERA TION About Mode Operation AUTO: ● Depending on the room temperature at the time operation begins, the operating mode will be switched automatically as shown in the accompanying table. Also, depending on the operating mode, the room temperature set- ting will cause the “standard” temperature to be set as shown.
En-7 AIR CLEANING OPERA TION 2 Press the AIR CLEAN button (Fig. 6 N ). The AIR CLEAN indicator lamp (Fig. 3 7 ) will light up (green, as shown in the figure). ● Air conditioning and Air Cleaning will function simultaneously. Air cleaning ● During operation, the unit produces a small amount of ozone that can be smelled.
En-8 TIMER OPERA TION T o Use the ON timer or OFF timer 1 Press the ST ART / STOP button (Fig. 6 M ). (if the unit is already operating, proceed to step 2). The indoor unit's OPERA TION Indicator Lamp (red) (Fig. 3 5 ) will light. 2 Press the TIMER button (Fig.
En-9 SLEEP TIMER OPERA TION Unlike other timer functions; the SLEEP timer is used to set the length of time until air conditioner operation is stopped. T o Use the SLEEP T imer 1 While the air conditioner is operating or stopped, press the TIMER button (Fig.
En-10 ADJUSTING THE DIRECTION OF AIR CIRCULA TION V ertical (up-down) direction of airflow is adjusted by pressing the Remote Control Unit’ s SET button. Horizontal (right-left) airflow direction is adjusted manually, by moving the Air Flow Direction Louvers.
En-11 SWING OPERA TION Begin air conditioner operation before performing this procedure. T o select SWING Operation Press the SWING button (Fig. 6 P ). The SWING indicator lamp (orange) (Fig. 3 8 ) will light. In this mode, the Air Flow Direction Louvers will swing automatically to direct the air flow both up and down.
En-12 Before cleaning the plasma filter unit, be sure to turn off the power supply to the air conditioner. Electric shock may result. ● When used for extended periods, the unit may accumulate dirt inside, reducing its performance. W e recommend that the unit be inspected regularly, in addition to your own cleaning and care.
En-13 CLEANING THE PLASMA AIR CLEANING FIL TER CAUTION! W ARNING! ● Make sure the plasma filter unit is properly mounted before cleaning or performing other tasks on it. If the unit is not properly mounted, it could fall off and cause damage or injury.
En-14 5. Install the air filter. ● Please consult instructions for cleaning the air filter on page 12. 6. Close the intake grille. Push the intake grill in at 4 points (the two ends of its lower side as well as two center points of the lower side, as shown in the figure) to close it.
En-15 Air -cleaning and Deodorizing filter maintenance As well as ensuring the maintenance of the dust collecting unit, please also take care of the filter. (Please carry out maintenance on the filter every 6 months.) 1. Open the intake grille and remove the air filter from the right side.
En-16 TROUBLESHOOTING In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the Power Supply Plug, and consult authorized service personnel. Merely turning off the unit’ s power switch will not completely disconnect the unit from the power source.
En-17 TROUBLESHOOTING Symptom Doesn’ t operate at all: Poor Cooling or Heating performance: The unit operates differently from the Remote Control Unit’ s setting: See Page — 8 - 9 — 5 4 CHECK .
En-18 OPERA TING TIPS Outdoor temperature Indoor temperature Cooling/Dry Mode About 32 to 115 °F About 64 to 90 °F T emperature and Humidity Range If the unit is used for long periods under high-humidity conditions, condensation may form on the surface of the indoor unit, and drip onto the floor or other objects underneath.
デバイスFujitsu AOU12CQの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Fujitsu AOU12CQをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFujitsu AOU12CQの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fujitsu AOU12CQの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fujitsu AOU12CQで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fujitsu AOU12CQを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFujitsu AOU12CQの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fujitsu AOU12CQに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFujitsu AOU12CQデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
