FujitsuメーカーAP-600RP-USBの使用説明書/サービス説明書
ページ先へ移動 of 63
.
CONNECT2AIR™ WLAN AP-600RP-USB Page 1 / 62 CONNECT2AIR™ WLAN AP-600RP-USB Manual Technical Support: http://support.fujitsu-siemens.de/DriverCD/Accessories/_DriverSteuer ung/GB/Accessories_WLAN.htm Manual Version 1.20 EN / June 22 nd 2004 / Manual_AP-600 RP-USB_V1-20_EN.
CONNECT2AIR™ WLAN AP-600RP-USB Page 2 / 62 FCC Information This device complies with Part 15 of the FCC Rule s. O peration is subject to the following two conditions: (1) This device may not cause h armful interference (2) This device must accept any interfere nce received; including interference that may cause unde sired op- eration.
CONNECT2AIR™ WLAN AP-600RP-USB Page 3 / 62 CONTENT 1 INTRODUC TION .......................................................................................................... 5 1.1 Five steps to success ...............................................
CONNECT2AIR™ WLAN AP-600RP-USB Page 4 / 62 8.5 Advanced Settings .......................................................................................................... 45 8.5.1 Virtual Server .....................................................
CONNECT2AIR™ WLAN AP-600RP-USB Page 5 / 62 1 INTRODUCTION Congratulations on your purchase of t he outstanding Wireless Broadband Router AP- 600RP-USB.
CONNECT2AIR™ WLAN AP-600RP-USB Page 6 / 62 Determine your network knowledge The success of the installati on of your AccessPoint and wirel ess clients is largely inde- pendent of your technical skills. The more advanced and familiar you are with networking terminology, the more intuitively you will act.
CONNECT2AIR™ WLAN AP-600RP-USB Page 7 / 62 2 FUNCTIONS AND FEA TURES • High-speed wirel ess LAN connection 54 Mbps data rate using the OFDM multicarrier modulation procedure • Roaming Seamless roaming within the IEEE 802. 11b and 802.11g WLAN infrastructure • IEEE 802.
CONNECT2AIR™ WLAN AP-600RP-USB Page 8 / 62 3 WLAN: OVER VIEW Wireless LAN (WLAN) basically offers the same functionality and flexibility as a fixed net- work, allowing the configuration of both se rver-based networks and peer-to-peer connec- tions. While initial speeds were less than 1 Mbps per second, this figure has now risen to 54 Mbps.
CONNECT2AIR™ WLAN AP-600RP-USB Page 9 / 62 In this configuration, network packets are sent and received directly by the intended transmitting and receiving stations. As long as the stations are within range of one another, this is the easiest and least expensive way to set up a wireless network.
CONNECT2AIR™ WLAN AP-600RP-USB Page 10 / 62 4 HARDW ARE INST ALLA TION 4.1 Front Panel LED indicators LED Function Color Status Description PWR Power indication Green On The power is on. Green On An active device is connected to the WAN port. WAN Link status Green Flashing The WAN port is sending or receiving data.
CONNECT2AIR™ WLAN AP-600RP-USB Page 11 / 62 4.3 Procedure for Hardware Installation 1. Decide where to pl ace your AccessPoint You can place your AccessPoint (AP) on a desk or another flat surface or mount it on a wall.
CONNECT2AIR™ WLAN AP-600RP-USB Page 12 / 62 5 NETWORK SETTINGS In order to use your AccessPoi nt and the printer server functi onality correctly, it is neces- sary to ensure, that the net work settings are configured co rrectly on your computers. 5.
CONNECT2AIR™ WLAN AP-600RP-USB Page 13 / 62 5.2 Client Network Settings 5.2.1 Network Settings Regardless of whether you are using a wirel ess or wired device to connect to your Ac- cessPoint, all the following steps must be followed for your network adapter: 1.
CONNECT2AIR™ WLAN AP-600RP-USB Page 14 / 62 5.2.3 Check the Connection Your wireless client has to be conf igured properly to connect to the AP. When the TCP/IP communication protocol has been installed, you can use the ping com- mand to check if your computer has successf ully connected to the AccessPoint.
CONNECT2AIR™ WLAN AP-600RP-USB Page 15 / 62 6 CONFIGURA TION EXAMPLES The AP-600RP-USB offers a wide range of configurati on possibilities due to the extended feature set. This chapter helps you to m anage more complex configuration schemes and helps you in configuring your AccessPoint as well as other devices in the network, like ADSL Routers.
CONNECT2AIR™ WLAN AP-600RP-USB Page 16 / 62 6.1 AP-600RP-USB with ADSL Router ( 1 ) ADSL Router ( 2 ) AP-600RP-USB ( 3 ) Notebook WAN: PPPoE over ADSL LAN: static IP: 192.168.1.1 DHCP on: 192.168.1.10 - 90 GW: 192.168.1.1 DNS: auto WAN: no ISP LAN: static IP: 192.
CONNECT2AIR™ WLAN AP-600RP-USB Page 17 / 62 6.2 AP-600RP-USB with ADSL Router (advanced) ( 1 ) ADSL Router ( 2 ) AP-600RP-USB ( 3 ) Notebook WAN: PPPoE over ADSL LAN: static IP: 192.168. 1 .1 DHCP on: 192.168. 1 . 10 - 90 GW: 192.168. 1 .1 DNS: auto WAN: dynamic IP address LAN: static IP: 192.
CONNECT2AIR™ WLAN AP-600RP-USB Page 18 / 62 6.3 AP-600RP-USB with ADSL Modem ( 1 ) ADSL Modem ( 2 ) AP-600RP-USB ( 3 ) Notebook No configuration necessar y WAN: PPP over Ethernet LAN: static IP: 192.168.1.254 DHCP on: 192. 168.1.10 - 90 GW: 192.168.
CONNECT2AIR™ WLAN AP-600RP-USB Page 19 / 62 6.4 AP-600RP-USB with CABLE Modem ( 1 ) Cable Modem ( 2 ) AP-600RP-USB ( 3 ) Notebook The Cable Modem does not have to be configured. WAN: dynamic IP address LAN: static IP: 192.168.1.254 DHCP on: 192. 168.
CONNECT2AIR™ WLAN AP-600RP-USB Page 20 / 62 6.5 Two AP-600RP-USB in repetition mode (WDS) ( 2 ) AP-600RP-USB Floor 1 ( 3 ) AP-600RP-USB Floor 2 ( 4 ) Notebook WAN: PPP over Ethernet LAN: static IP: 192.168.1.254 subnet Mask: 255.255.255.0 DHCP on: 192.
CONNECT2AIR™ WLAN AP-600RP-USB Page 21 / 62 7 SOFTW ARE INST ALLA TION The software provided with the installation WLAN CD contains all drivers, documentation and software for WLAN products availabl e from Fujitsu Siemens Computers.
CONNECT2AIR™ WLAN AP-600RP-USB Page 22 / 62 8 ACCESSPOINT CONFIGURA TION This product is provided with a Web-based configuration in terface that can be accessed via your Web browser, such as Internet Explorer, Netscape Comm unicator or any other HTML-compatible browsers.
CONNECT2AIR™ WLAN AP-600RP-USB Page 23 / 62 8.2 System Status This section shows the AP’s working status: • AccessPoint properties The wireless network name is displayed. • Wide Area Network (WAN) The status of the WAN port will be disp layed as well as the connection type.
CONNECT2AIR™ WLAN AP-600RP-USB Page 24 / 62 8.3 Wizard The Wizard section will guide you through the main settings for your AccessPoint. You will be prompted to select your ISP (Internet Service Provider) and to check your security set- tings.
CONNECT2AIR™ WLAN AP-600RP-USB Page 25 / 62 Dynamic IP Address All settings are provided by the ISP or ar e automatically accepted by the AccessPoint.
CONNECT2AIR™ WLAN AP-600RP-USB Page 26 / 62 L Use „auto-connection“ if y ou do not have a connection with flatrate (no capacity download restriction). Please check thoroughl y if your AP is disconnecting. This can be done via the status page or check your ISPs accounting information.
CONNECT2AIR™ WLAN AP-600RP-USB Page 27 / 62 • L2TP Use the information provided by the pr ovider for making your L2TP settings. • Without an ISP If you wish to use the device purely as an AccessPoint (i.e., without connection to a provider), select this option.
CONNECT2AIR™ WLAN AP-600RP-USB Page 28 / 62 8.3.2 Wireless Settings • Country / Region: Select the country in which the AccessPoint is to be used. The selection determines which radio channels can be used to transmi t and receive signals as regulated by the corresponding authorities.
CONNECT2AIR™ WLAN AP-600RP-USB Page 29 / 62 8.3.3 Wired Equivalent Privacy (WEP) Security Use this security standard to obtain at least the minimum in security in your WLAN. To use WEP in the AccessPoint, all clients must have standardized security settings.
CONNECT2AIR™ WLAN AP-600RP-USB Page 30 / 62 8.4 Primary Setup These core options are essential to enable the AP to work properly. The available settings and the interface depend on the WAN type.
CONNECT2AIR™ WLAN AP-600RP-USB Page 31 / 62 ered up. The DHCP server settings include th e following items and can be “Disabled” or “Enabled”.
CONNECT2AIR™ WLAN AP-600RP-USB Page 32 / 62 8.4.4 Address Reservation In spite of the use of a DHCP server, fixed al location of IP addresses is possible within the network – by address reservation. With this function you can assign a particular IP address to a MAC address.
CONNECT2AIR™ WLAN AP-600RP-USB Page 33 / 62 8.4.6 WAN Type Configuration / C onnection to the Internet (ISP) WAN Type: Select the appropriate WAN connec tion type for your ISP. You can choose between different types by clicking on "Change".
CONNECT2AIR™ WLAN AP-600RP-USB Page 34 / 62 8.4.7 Wireless Settings • Country / Region: Select the country in which the AccessPoint is to be used. The selection determines which radio channels can be used to transmi t and receive signals as regulated by the corresponding authorities.
CONNECT2AIR™ WLAN AP-600RP-USB Page 35 / 62 8.4.8 WLAN Security To protect your intellectual property, secure your wir eless connection! This Access- Point is equipped with a sophisticated securi ty algorithm to protect against intruders entering your system or list ening to what you are transferring over your network.
CONNECT2AIR™ WLAN AP-600RP-USB Page 36 / 62 Wireless Security Settings: The AP-6000RP-USB offers five methods for achieving a WL AN with enhanced security. As described in the table above, there ar e dependencies between authentication and en- cryption.
CONNECT2AIR™ WLAN AP-600RP-USB Page 37 / 62 8.4.10 Wired Equivalent Privacy (WEP) Settings Use this security standard to obtain at least the minimum in security in your WLAN. To use WEP in the AccessPoint, all clients must have standardized security settings.
CONNECT2AIR™ WLAN AP-600RP-USB Page 38 / 62 8.4.11 Wi-Fi Protected Access™ (WPA) WPA: Besides VPN (Virtual Private Network), cu rrently one of the highest levels of security a wireless network can achieve.
CONNECT2AIR™ WLAN AP-600RP-USB Page 39 / 62 8.4.12 IEEE 802.1x IEEE 802.1x is a standard for network acce ss control (port-based), which was introduced especially for distributing encryption keys in a wireless network.
CONNECT2AIR™ WLAN AP-600RP-USB Page 40 / 62 8.4.13 Radius Server RADIUS (Remote Authentication Dia l-In User Service) plays a central role in the network in providing the capabilities of authenticating, aut horizing, accounting, auditing and alarm- ing, etc.
CONNECT2AIR™ WLAN AP-600RP-USB Page 41 / 62 8.4.14 Access Control List The MAC Address Control allows you to assi gn different access rights for different users and to assign a specific IP address to a certai n MAC address. A distinction is made as to whether the AccessPoint always allows access to each client, or if it excludes all clients.
CONNECT2AIR™ WLAN AP-600RP-USB Page 42 / 62 User-specific access list: Rights (always allow access / deny access) are assigned to the clients in the table inde- pendently of the general access mode. If a client is always to have access to the whol e network (e.
CONNECT2AIR™ WLAN AP-600RP-USB Page 43 / 62 Enter the user name and password you configured for your DDNS provider. If you use a wildcard , all host names will be diverted to the main host. For example, First.mycam.dyndns.org or Second.mycam.dyndns .
CONNECT2AIR™ WLAN AP-600RP-USB Page 44 / 62 8.4.16 WDS Extend the range of your netwo rk without having to use cables to link the AccessPoints by using the Wireless Distribution System (WDS): Normally, AccessPoints are linked to each other via cables.
CONNECT2AIR™ WLAN AP-600RP-USB Page 45 / 62 8.5 Advanced Settings 8.5.1 Virtual Server The router built into the AP- 600RP-USB allows specific ports – and therefore their associ- ated services – to be enabled for communication fo r particular clients.
CONNECT2AIR™ WLAN AP-600RP-USB Page 46 / 62 8.5.2 Firewall The firewall is a set of programs located at the gateway, which limits the exposure of a computer or a group of computer s to users in the WAN network or Internet.
CONNECT2AIR™ WLAN AP-600RP-USB Page 47 / 62 Firewall configuration The firewall must be disabled before you can make any changes to it. Confirm the changes made by saving. Even if the firewall is disabled, the routing (WLAN access to the LAN/WAN) and the masking (NAT) are still active .
CONNECT2AIR™ WLAN AP-600RP-USB Page 48 / 62 Once you have activated a rule, you must assi gn a response (a logical sequence) to it – you can select from four possible responses: Accept: The data is allowed to pass through. Drop: The data traffic will be stopped, with no response to the sender.
CONNECT2AIR™ WLAN AP-600RP-USB Page 49 / 62 Example of a firewall configuration General network configuration FTP Server 192.168.1.12 Port: 21 LOCAL WEB Server 192.168.1.13 Port: 80 LOCAL Laptop 1 192.168.1.100 LOCAL Laptop 2 192.168.1.101 LOCAL Desktop PC 192.
CONNECT2AIR™ WLAN AP-600RP-USB Page 50 / 62 RULE 1 RULE 2 The first assumption is satisfied because all PC s in the local network are allowed to surf the Internet. What is still missing is that PC 2 can configure the AP from the Internet, so new rules have to be defined for this purpose.
CONNECT2AIR™ WLAN AP-600RP-USB Page 51 / 62 Verification: • Open a DOS dialog box on the desktop PC2 and try to ping the WAN port of the AccessPoint (212.35.65.205) Æ ping OK • Open a DOS dialog box on the desktop PC3 and try to ping the WAN port of the AccessPoint (212.
CONNECT2AIR™ WLAN AP-600RP-USB Page 52 / 62 8.5.3 Time Zone For events to be displayed in the log in terms of their time of occurrence with regard to a specific time zone, an update is performed over the Internet. The update is prompted via NTP (Network Time Protocol).
CONNECT2AIR™ WLAN AP-600RP-USB Page 53 / 62 8.6 Toolbox 8.6.1 Administrator Toolbox Change the system password as quickly as possi ble since your conf iguration will other- wise remain unprotected.
CONNECT2AIR™ WLAN AP-600RP-USB Page 54 / 62 9 ACCESS TO USB PRINTERS THROUGH WLAN This product provides the functi on of wireless-sharing of specif ic USB printers for Microsoft Windows 2000/XP users in the network.
CONNECT2AIR™ WLAN AP-600RP-USB Page 55 / 62 Step 4 Step 5 4. Select “Create a new port” and th en “Standard TCP/IP Port” and press Next. 5. Press Next. Step 6 Step 7 6. Add the AccessPoints IP address in the fi rst field. Default value of the AP-600RP- USB is 192.
CONNECT2AIR™ WLAN AP-600RP-USB Page 56 / 62 8. The port and printer name will be shown. Ch oose “Protocol” “LPR” and type in the “LPR Settings” “WLAN_printing”. Tick “LPR Byte Counting Enabled”. Press OK . 9. Press Finish. Step 10 Step 11 10.
CONNECT2AIR™ WLAN AP-600RP-USB Page 57 / 62 Appendix A: Licensing Information This product includes third- party software licensed under t he terms of the GNU General Public License. You can modify or redistri bute this free software under the terms of the GNU General Public Licence.
CONNECT2AIR™ WLAN AP-600RP-USB Page 58 / 62 Software Foundation software is covered by t he GNU Library General Public License in- stead.) You can apply it to your programs, too. When we speak of free software, we are re ferring to freedom, not pr ice.
CONNECT2AIR™ WLAN AP-600RP-USB Page 59 / 62 all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Pr ogram a copy of this License along with the Program.
CONNECT2AIR™ WLAN AP-600RP-USB Page 60 / 62 c) Accompany it with the information you rece ived as to the offer to distribute corre- sponding source code. (This alternative is allowed only for noncommercial distribu- tion and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.
CONNECT2AIR™ WLAN AP-600RP-USB Page 61 / 62 mented by public license prac tices. Many people have made generous contributions to the wide range of software distributed through that system in relianc.
CONNECT2AIR™ WLAN AP-600RP-USB Page 62 / 62 ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILI TY OF SUCH DAMAGES.
デバイスFujitsu AP-600RP-USBの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Fujitsu AP-600RP-USBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFujitsu AP-600RP-USBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fujitsu AP-600RP-USBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fujitsu AP-600RP-USBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fujitsu AP-600RP-USBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFujitsu AP-600RP-USBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fujitsu AP-600RP-USBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFujitsu AP-600RP-USBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。