Fujitsuメーカーfi-6010Nの使用説明書/サービス説明書
ページ先へ移動 of 21
.
i Contents Introduction .................. ............................................................... iii ■ Manuals ...................... ............................................................ ......... iii ■ Regulatory Informatio n ..
iii Introduction Thank you for purch asing the fi-6010N Net work Scanner. This easy-to-operate network scanner is used to scan documents for further use.
v OCR by ABBYY Software House. All rights reserved. ABBYY , FineReader are trademarks of ABBYY Software House. Other product names are the trademarks or registered trademarks of the respective compa nies.
vii Do not touch the insi de of the scanner unless necessary . Do not use the scanner if you smell a strange odor . Do not use aerosol sprays near the scanner . Do not place the scanner within the reach of small children. Do not touch the heated section for a long time.
1 Chapter 1 Scanner Features 1.1 Scanner Features ■ Use for scanned documents with ease This easy-to-operate network scanner may be used to scan documents for further use: 1. Scanned document files can be sent as an e-mail attachment. 2. Scanned document files can be sent by fax.
3 1.5 Names and Functions of Parts This section describes the scanner parts and their func- tions. ■ Front ■ Rear ■ Removable Parts Parts that can be removed from the scanner are dis- played below.
5 2.4 Attaching the Keyboard Cover The layout of the keyboard may d iffer according to the language selected for the operating enviro nment. The layout of each keyboard co ve r is prepared according to language requirements. Take the keyboard cover for the selected language out of its p ackaging, and attach it to the scanner.
7 5. Enter the password. Password is case sensitive. Enter "password" here. 6. Press the [Login] button. ⇒ If the administrator name and password are valid, the "System Settings" screen appears. 3.2 Changing the Administrator Password The administrator pass word can be changed.
9 3. Set the scanner's IP address. This may be done automatically, by pressing the DHCP [On] button. The IP address may also be set manually, by pressing the DHCP [Off] button and entering the following numerical addresses: • IP Address • Subnet Mask • Default Gateway 4.
11 4. Enter the following numerical addresses: • Primary WINS • Secondary WINS If a WINS server setting is not required, enter "0.0.0.0". 5. Press the [OK] button. ⇒ The information entered is set. Next, check the network connectio n. 3.
13 ⇒ The "File Download - Security Warning" screen appears. 5. Press the [Run] button. ⇒ The fi Network Scanner Admin Tool Setup Wizard appears. 6. Press the [Next] button. ⇒ The "Select Installation Folder" window appears. 7.
15 Chapter 6 Performing a Scan T est Perform a scan test to determine if the scanner is work- ing properly. Login as a regul ar user to perform the scan test. 1. Load the documents to be test scanned. ⇒ The "Login" screen appears. However, if the scanner is setup for automatic login, the "Login" screen is not shown.
17 If some other error occurs • Message An error has occurred. Tr y turning the power off and back on again. The administrator should contact the FUJITSU scanner dealer or an autho- rized FUJITSU scanner service provider for help.
19 Appendix B Scanner Care ■ Cleaning Materials Contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider to obtain these products.
21 Appendix C Replacing Part s ■ Part No. and Replacement Cycle for Consumable Parts The usage count of consumable parts ca n be checked in the "Usage Status" screen on the [Device Status] tab. When parts need to be replaced soon, the "Status" infor- mation field becomes orange.
23 Appendix D Network Connection T roubleshooting ■ Checking Basic Network Operation with a Ping T est If a network connection is no t possible, refer to "3.9 Check ing the Network Connectio n" (page 11) for ping results and how to deal with them.
25 ■ Failure to Connect to a Server using its Host Name or FQDN If a server cannot be connected to by usin g its host name or FQDN, and does not respond to a ping te st, try the following steps: ■.
27 Appendix E T roubleshooting Problem Check Item Suggestion Scanner cannot be turned on. Has the Startup button been pressed? Press the Startup button. Are the AC cable and AC adapter properly connected to the scanner? Connect the AC cable and the AC adapter.
29 Copyright NetAdvant age 2007 Copyright 2000-2007 Infragistics, Inc. LEADTOOLS for .NET Copyright© 2005 LEAD T echnologies, Inc. WinP cap3.1 Copyright © 1999 - 2005 NetGroup, Po litecnico di T orino (Italy). Copyright © 2005 - 2006 CACE T ech nologies, Davis (California).
31 The name of Juniper Networks ma y not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTW ARE IS PROVIDE D "AS IS" AND .
デバイスFujitsu fi-6010Nの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Fujitsu fi-6010Nをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFujitsu fi-6010Nの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fujitsu fi-6010Nの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fujitsu fi-6010Nで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fujitsu fi-6010Nを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFujitsu fi-6010Nの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fujitsu fi-6010Nに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFujitsu fi-6010Nデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
