FujitsuメーカーP3PC-3062-02ENの使用説明書/サービス説明書
ページ先へ移動 of 27
P3PC-3062-02EN.
.
i CONTENTS INTRODUCTION .................... ....................................................... ii Regulatory Informatio n .......................... .............................. ii Liability .................................. .........
ii INTRODUCTION Thank you for purchasing the fi- 5950 Duplex Color Scanner. This document describes how to use fi-5950 and basic operation methods. Before you start u sing fi-5950 be sure to thoroughly read this manual to ensure correct use.
iii ■ Liability READ ALL OF THIS MANUAL CAREFULL Y BEFORE USING THIS PRODUCT . IF THIS PRODUCT IS NOT USED CORRECTL Y , UNEXPECTED INJUR Y MA Y BE CAUSED TO USERS OR BYST ANDERS. Also, keep this manual in a safe place so that it can be easily referred to during use of this product.
iv *1:Where there is no distinction between the diff erent versions of the above operatin g system, the general term "W indows" is used. *2:All the descriptions in this manual assume the usage of Adobe Acro bat bundled with this product. However , Adobe Acrobat may be upgraded without n otice.
v Screen Examples In This Manual The screen examples in this manual are subject to change without notice in the interest of product improvement. If the actual displayed screen differs from the screen .
vi Do not install the scanner in the following locations which are subject to high temperature, humidity , le ss ventilati on, or dust. If placed in an area subject to high temperature, the cover may become overheated and de formed, causing the scanner to become hot, resulting in a fire.
vii When installing the scanner on a table, make sure that the table is flat and level. Place the scanner so that none of its part s e xtend beyond the edge of the table, otherwise it may fall or collapse and cause injurie s. Install the scanner away from strong magnetic fields and other sour ces of electronic noise.
1 Chapter1 PREP ARING THE SCANNER 1.1 Checking the Contents of the Scanner Package When you unpack the scanner package, make sure that the package contains all the pa rts on the list included in the package. If any parts are missing or defectiv e, contact your scan- ner dealer or an authorized FUJITSU scanner service provider.
2 ■ Removable Parts 1.3 Operator Panel The operator panel is locate d on the rig ht side of the scanner. The panel consists of a Function Number Dis- play, buttons and a LED.
3 ■ Indications on the Function Number Display The following shows the in dications on the Function Number Display. Use this button to start linked applica- tion. When this button is pressed during scanning operation, the scanning is cancelled (*About the settings, refer to the "fi- 5950 Operator’s Guid e" on the Setup DVD-ROM).
4 Chapter2 INST ALLA TION OF THE SCANNER 2.1 Installing the Scanner 1. Place the scanner at its installation site. For details on the scanner's dimensions and required installation space , refer to the fi-5950 Operator’s Guide, chapte r "10.
5 ■ Connecting the SCSI interface When using the scanner with a SCSI interface, the fol- lowing SCSI cable and SCSI card mu st be purchased. • SCSI cable Use a SCSI cable whose connector on the scan- ner side is the 68-pin hi gh-density shielded-type and whose connector on the PC side fits the con- nector of the SCSI card to use.
6 3. When using the SCSI cable, set th e SCSI ID using the SCSI ID switch on the back of th e scanner. (Refer to step 3 in "Connecting the SCSI interface" on page 5 .) 4. Press the "I" side of the main power switch to turn on the scanner.
7 ■ System Requirements The system requirements for fi-5950 are as follows. *1: Scanner Central Admin Agent is not supported. *2: Not supported by Kofax VRS. *3: QuickScan Pro d oes not support t he Windows 64-bit version. *4: ScandAll PRO and Scan to Micros oft SharePoint are not supported.
8 4. Install the softwa re, following the onscreen instructions. INSTALL (Custom) 1. Perform Steps 1 and 2 in "INSTALL (Recom- mended)" (page. 7) . 2. Click the [INSTALL (Custom)] button. ⇒ The [INSTALL PROD UCTS] screen appears. 3. Click the button of the software to be installed.
9 2.4 Checking Scanner Driver Operation This section explains how to check the operation of the installed scanner driver by using ScandAll PRO. Make sure that the scanner driver is installed properly, following the procedure below. ■ Checking the Operation of the Scanner Driver 1.
10 9. In the [Scan Settings] dialog box, clear the [Sa ve to file] checkbox. 10. Click [Scanner Settings]. ⇒ A setup dialog box appears for you to configure scanner driver settings. 11. Configure scanner settings such as the resolution and paper size.
11 • To remove FUJITSU Scanner USB HotFix, select " FUJITSU Scanner USB HotFix ." 5. Clic k the [Change/ Remove] button or the [Remove] button. 6. When you see a confirmation dialog box, click the [OK] button or the [Yes] button. ⇒ Upon clicking the button, uninstallation is started.
AP-1 Appendix 1 TROUBLESHOOTING ■ Troubleshooting checklist Symptom Check this item Remedy Scanner does not turn on. Have you pushed the power button on the front of the scanner? Push the power b utton. Have you pushed the main power switch at the back of the scanner? Push the Main power switch of the scanner.
AP-2 Paper is not fed (pick error occurs frequen tly, or docu- ment stops midway). Do the documents satisfy the "Docu- ment Quality" and the "Multifeed Detec- tion Conditions" in t.
AP-3 ■ Temporary error The following shows the procedure for releasing of each of the temporary errors. • "J0" or "U1" error 1. Remove the document jammed or stopped in the ADF. (Refer to the fi-5950 Operator’s Guide "6.
AP-4 Appendix 2 DAIL Y CARE ■ Cleaning Materials *1: For details about the clean ing materials, contact the FUJITSU scanner dealer where you purchased the scanner. *2: Pre-moistened with Cleaner F1, Cleaning Wipes are used instead of mo istened cloths.
AP-5 Appendix 3 REPLACING CONSUMABLES ■ Consumables and Replacement Cycle The followings are the specif ications of consumables and their recommended replacement cycles. To purchase consumables, conta c t the store where you purchased the scanner or an authorized FUJITSU scanner service provider.
AP-6 ■ Pick roller ■ Separator roller ■ Brake roller Pick roller Separator roller Pad Cover Brake roller Cover.
z Copying of the contents of this manual in whole or in part and copying of the scanner applicat ion is prohibited under the copyright la w. z The contents of this manual are subject to change without notice.
デバイスFujitsu P3PC-3062-02ENの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Fujitsu P3PC-3062-02ENをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFujitsu P3PC-3062-02ENの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fujitsu P3PC-3062-02ENの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fujitsu P3PC-3062-02ENで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fujitsu P3PC-3062-02ENを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFujitsu P3PC-3062-02ENの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fujitsu P3PC-3062-02ENに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFujitsu P3PC-3062-02ENデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
