Fujitsu Siemens ComputersメーカーRX600 S3の使用説明書/サービス説明書
ページ先へ移動 of 17
PRIMERGY RX6 00 S3 incl. SAS version System configurator and order-information guide Contents Instructions Configuration diagram Configurator 0 0 System software 1 I Basic unit 2 II Processor 3 III Me.
System configurator and order-information guide PRIMERGY RX600 S3 Status 2007-01-24 Instructions This document contains basic product and configuration information that will enable you to configure yo.
System configurator and order-information guide PRIMERGY RX600 S3 Status 2007-01-24 Configuration diagram PRIMERGY RX600 S3 TOP View System unit ( I ) Extension slots Memory ( III ) SCSI / RAID controller ( VIII ) Fiber Channel ( IX ) Communication/Network ( X ) 7 6 5 4 Processors must be plugged in order according the picture.
PRIMERGY-Software Configurators and Release Lists Start "PRIMERGY RX600 S3" PRIMERGY RX600 S3 Status 2007-01-24 SW - Configurator 32 bit with OEM-Software without OEM-Software for PRIMERGY S.
PRIMERGY-Software Configurators and Release Lists Start "PRIMERGY RX600 S3" PRIMERGY RX600 S3 Status 2007-01-24 SW Configurator EM64T with OEM-Software without OEM-Software for PRIMERGY Serv.
System configurator and order-information guide Start PRIMERGY RX600 S3 PRIMERGY RX600 S3 Status 2007-01-24 Section I Basic unit PRIMERGY RX600 S3 SCSI PRIMERGY RX600 S3 SAS Rack unit 4U Rack unit 4U .
System configurator and order-information guide A PRIMERGY RX600 S3 Status 2007-01-24 Section II Processor A 4-way processor system requires a multi-processor operating system Later upgrading to a four-way-processor system is also possible VRM´s for 1st/2nd CPU are on the Motherboard, for the 3nd / 4th CPU addition VRM Modules are required.
System configurator and order-information guide B PRIMERGY RX600 S3 Status 2007-01-24 Section III Memory The system can be equipped with up 4 memory boards with 2 memory banks each. One Memory Board is allready supplied in the base unit. Each memory board can be equipped with up to 2x 8GB = 16GB memory.
System configurator and order-information guide C PRIMERGY RX600 S3 SAS Status 2006-12-31 Section IV on-board SCSI / SAS Controller SCSI Base Units The system is equipped with a two channel Utra 320 onboard SCSI controller including a full featured RAID controller with 256MB Cache (suporting the RAID level 0, 1, 5, 10, 50).
System configurator and order-information guide D PRIMERGY RX600 S3 Status 2007-01-24 SAS Base Units AB. on-board SCSI-/ SAS RAID-Controller for accessible drives and SAS HDD´s -> SAS Version The .
System configurator and order-information guide E PRIMERGY RX600 S3 Status 2007-01-24 Section V USB devices / optical devices One of the following USB devices must be used for integrating the drivers during installation process if no automized (e.
System configurator and order-information guide F PRIMERGY RX600 S3 Status 2007-01-24 Section VII Tapes devices S26361-F3128-E101 internal SCSI-Cable for connetion of internal Tape devices max.
System configurator and order-information guide G PRIMERGY RX600 S3 Status 2007-01-24 Section VIII optional SCSI / RAID controller B. SCSI - controller for internal and external devices. S26361-F2399-E1 1-channel SCSI U160 Controller Adaptec 29160 plug: internal: HD 50-pin & HD68 max.
System configurator and order-information guide H PRIMERGY RX600 S3 Status 2007-01-24 Section IX Fibre channel controller Qlogic controller Emulex Controller No mix and match for Qlogic and S26361-F30.
System configurator and order-information guide I PRIMERGY RX600 S3 Status 2007-01-24 Section X Communication / Network on-board LAN Controller Teaming: Failover, Load Balancing Dual Gbit Ethernet Contr.
System configurator and order-information guide J PRIMERGY RX600 S3 Status 2007-01-24 Section XI System Management Products (RemoteView) S26361-F1790-E221 S26361-F2425-E103 RemoteView Software V5.
System configurator and order-information guide PRIMERGY RX600 S3 Status 2007-01-24 Change Report Date Order number Changes 2007-01-24 S26361-F3124-E200 VRM module for 3rd/4th CPU - no longer available 2007-01-24 S26361-F3124-E361 Processor Xeon MP 3.
デバイスFujitsu Siemens Computers RX600 S3の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Fujitsu Siemens Computers RX600 S3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFujitsu Siemens Computers RX600 S3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fujitsu Siemens Computers RX600 S3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fujitsu Siemens Computers RX600 S3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fujitsu Siemens Computers RX600 S3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFujitsu Siemens Computers RX600 S3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fujitsu Siemens Computers RX600 S3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFujitsu Siemens Computers RX600 S3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。