FurunoメーカーFA-150の使用説明書/サービス説明書
ページ先へ移動 of 58
Installation Manual UAIS TRANSPONDER F A-150 SAFETY INSTRUCTIONS ............................................................................................................ .........I SYSTEM CONFIGURA TIONS ...........................................
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : NOV 2004 . Printed in Japan All rights reserved.
i WARNING Turn off the power at the switch- board before beginning the installation. Fire or electrical shock can result if the power is left on. Do not install the equipment where it may get wet from rain or water splash. Water in the equipment can result in fire, electrical shock or damage the equipment.
ii SYSTEM CONFIGURA TION : Standard : Option GPS/VHF combined antenna GVA-100 GPS antenna GSC-001 GPA-017S Distributor unit DB-1 VHF antenna Power supply PR-240 100-115/ 200-230 VAC 1 φ , 50/60Hz 12-.
iii EQUIPMENT LISTS S t andard supply No. Name T ype Code no. Qty Remarks 1 UAIS T rans p onder F A -1501 - 1 2 Monitor Unit F A -1502 - 1 GSC-001 - GPS Antenna GP A -017S - 3 GPS/VHF Combined GV A -100 - 1 Select one.
iv Optional supply No. Name T ype Code no. Remarks 1 Monitor unit F A-1502 - CP20-02700 004-381-160 8D-FB-CV(30m)+CP20-02701 2 Antenna cable set CP20-02710 004-381-170 8D-FB-CV(50m)+CP20-02701 CP24-00.
1 1. MOUNTING NO TICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solv ents that can damage coating and plastic par ts, especially plastic connectors. 1.1 Antenna Unit s 1.
2 How to att ach the connector N-P-8DFB for cable 8D-FB-CV Outer Sheath Ar mor Dimensions in millimeters. Inner Sheath Shield Remov e outer sheath and ar mor by the dimensions shown left. Expose inner sheath and shield by the dimensions shown left. Cut off insulator and core by 10mm.
3 1.1.2 VHF antenna Location The location of the mandatory AIS VHF- antenna should be carefully considered. Digital communication is more sensitive than analog/voice communication to interference created by reflections in obs tructions like masts and booms.
4 • When coaxial cable RG-10/UY (shipyard s upply) is used, attach the coaxial plug M-P-7 (dockyard supply) as shown on the next page. Horizontal sep aration distance More than 10 m More than 0.
5 How to att ach the plug M-P-7 Lay the coaxial cable and attach an M-ty pe plug (if necessary) to the cable as follows. 1. Remove the sheath by 30 mm. 2. Bare 23 mm of the center conductor . T rim braided shield by 5 mm and tin. 3. Slide coupling ring onto cable.
6 Mounting procedure 1. Dismount the bottom cover , cut the ca ble-tie inside the unit and take out the coaxial connector attached to the combined box. 2. Loosen four screws to loosen whip an tenna fixture and pull out the coaxial connector coming from the combined box through the hole in the whip antenna fixture.
7 Stanchion The top of the stanchion comes into contact with the flange. Inst alling distributor unit DB-1 The length of the cable between the distribut or unit and transponder unit is 1 m so locate the distributor unit within 1 m fr om the transponder unit.
8 1.2 Monitor Unit The monitor unit can be installed on a desktop or flush mounted in a p anel. Install it on the chart table or near the steering place, referring to the outline drawing. When selecting a mounting location for the monitor unit, keep the following in mind: • Keep the unit out of direct sunlight.
9 F type Use the optional flush mount kit OP20-29. Name T ype Code No. Qty Cosmetic panel 20-016-1051 100-251-370-10 1 Self-tapping screw 5x20 000-162-609-10 4 Hexagon-head bolt M6x12 000-162-897-10 2 S pring washer M6 000-158-855-10 2 1. Prepare a cutout in the mounting location whose dimensions are 183 (W) x 92 (H) mm.
10 1.3 UAIS T ransponder Mount the transponder , where it is protected from rain and water splash. This unit can be installed on a bulkhead. In st all it, referring to the outline drawing. When selecting a mounting location for the transponder, keep the following in mind: • Keep the transponder out of direct sunlight.
11 1.4 Power Supply (option) When selecting a mounting location fo r the unit, keep the following in mind: • Keep the unit out away from areas subject to water splash. • Locate the unit away from exhaust pipes and vents. • The mounting location s hould be well ventilated.
12 2. WIRING 2.1 Connection Connect the equipment, referring to the in terconnection diagram at the back this manual. GPS Antenna GSC-001 or GPS-017S PC 150M-W2VN or F AB-151D Either one RG-10U/Y RG-10U/Y Attached to Distributor (approx. 1m) Distributor unit DB-1 AC IN DC IN DC OUT 12-24 VDC (Connect to the alternative power source.
13 EXT ALM: Connect ship's alarm system. DISP: Connect the monitor unit. COM4 COM2 COM3 COM1 DC (-) DC (+) COM6 COM5 Blue Sign Internal ports of the T ransponder COM1: Long range communication device (Inmarsat C, etc.
14 *: Waterproofing connectors Wrap connector with vulcanizing tape and th en vinyl tape. Bind the tape end with a cable-tie. W aterproofing connector **: DPYC-2.5, TTYCS-1Q and TTYCS-4 are Japan Industry S tandard cables. Use them or the equivalents, referring to the Appendix.
15 How to att ach wires to the W AGO connector Procedure 1. T wist the cores. 2. Press the terminal opener downward. 3. Insert the wire to hole. 4. Remove the terminal opener . 5. Pull the wire to confirm that it is secure. T erminal opener Wiring for W AGO connector W AGO connector Wire T wist Press downward.
16 2.2 Changing Ship’ s Mains S pecifications The AC-DC power supply PR-240 is shipped ready for connection to a 200-230 V AC ship’ s mains. If the ship’s mains is 100 V AC-1 15 V AC, change the tap connection and terminal board connecti on as below .
17 3. SETTING AND ADJUSTMENT After inst alling the equipment, set up the ow n ship’s st atic information (MMSI, IMO number , ship’s name, call sign, type of ship and GPS antenna position). Also, set up the I/O ports. 3.1 Inland AIS S pecific Settings This section shows how to activate and set up the Inland AIS feature.
18 Selecting AIS mode The Inland AIS has two operating modes: Inland (inland waterways) and SOLAS (SOLAS compliant class A AIS transponder). Select INLAND AIS mode as follows: 1.
19 3. Enter the password to show the IN ITIAL SETTINGS menu. Note that the password is known by only the FURUNO dealer . [INITIAL SETTINGS] SET MMSI SET INT ANT POS. SET EXT ANT POS. SET SHIP TYPE SET I/O PORT SET BLUE SIGN SW QUIT [MENU] SET MMSI INITIAL SETTINGS menu 4.
20 3.2 Setting MMSI, IMO No., Name and Call Sign 1. Display the INITIAL SETTINGS menu re ferring to step 1-3 in "Setting blue sign status" on p age 18 - 19. [INITIAL SETTINGS] SET MMSI SET INT ANT POS. SET EXT ANT POS. SET SHIP TYPE SET I/O PORT SET BLUE SIGN SW QUIT [MENU] SET MMSI Appears for Inland AIS only INITIAL SETTINGS menu 2.
21 3.3 Setting GPS Antenna P osition 1. Open the INITIAL SETTINGS window , referring to step 1-3 in "Setting blue status" on p age 18 - 19. 2. Press ▲ or ▼ key to choose SET INT ANT POS. and pres s the [ENT] key . [SET INT ANT POS.] QUIT[MENU] SET INT ANT POS.
22 3.4 Setting Ship T ype 1. In the INITIAL SETTINGS window , press the ▲ or ▼ key to choose the SET SHIP TYPE and press the [ENT] key . [SET SHIP TYPE] TYPE NO : 0 * * * * * TYPE DETAIL * * * * NOT AVAILABLE 2. Press the [ENT] key and set number for ship type by using ▲ or ▼ key , referring to the table below .
23 3. Select an appropriate port among COM1, COM2, COM3, COM4, COM5 and COM6. If you chose COM1, for example, do as follows. 4. Press the [ENT] key to display the COM1 setting window . [SET COM1] MODE : LONG RANGE SPEED: IEC 61162-2 QUIT [MENU] 5. Press the [ENT] key again to display the MODE setting window .
24 The table below shows the port s and corresponding items to be set. Port and data format/dat a transmission rate Port External device (MODE) Format/Rate (SPEED) LONG RANGE IEC61 162-1, IEC61 162-2 .
25 Priority setup 1. Press ▲ or ▼ to choose SET PRIORITY at the SET I/O POR T sub-menu and press the [ENT] key . [SET PRIORITY] L/L, COG, SOG HDG ROT QUIT [MENU] PRIORITY menu 2. "L/L, COG , SOG" is selected; press the [ENT] key . [SET L/L, COG, SOG] COM4: 1 COM5: 2 COM6: 3 QUIT [MENU] 3.
26 Quality setup (Inland AIS only) If your speed, course or heading sensor is type approved, choose quality setting as shown below . 1. Press ▼ to choose SET QUALITY at the SET I/O POR T sub-menu then press the [ENT] key . QUIT[MENU] [SET QUALITY] SPEED : LOW COURSE : LOW HEADING : LOW 2.
27 4. A TT ACHING LAN KIT (OPTION) T o connect to PC network or NA VNET 3D network, the optional LAN kit is required. Name: LAN kit T ype: OP24-8 Code no.: 005-956-020 Name Code no. Qty Remark 1 NET100 board 008-535-840 1 03P9332 2 Hex. spacer 000-801-678 4 Att aching 1.
28 Setting LAN port for PC network 1. Press the [MENU] key , choose INIT IAL SETTING , enter password, choose SET I/O PORT and press the [ENT] key to show the SET I/O POR T sub menu. 2. Press ▲ or ▼ to choose SET LAN POR T and press the [ENT] key .
29 4. Press the [ENT] key , enter sub net ma sk in the SUB NET MASK field and press the [ENT] key . (Setting range: 000 .000.000.000 to 255.255.255.255) 5. Press the [ENT] key , enter port number in the NA VNET POR T NO. field and press the [ENT] key .
30 This page intentionally lef t blank..
31 5. IEC 61 162-1/2 DA T A SENTENCES IEC 61 162-1/2 format data is input or outp ut from the dat a port COM1-COM6. The table below shows the input/output dat a specifications. T ransponder Port Menu setting Input/Output Data format LONG RANGE Input/Output* IEC61 162-2 (38.
32 Input dat a/Sentences Sentence (Priority) Contents ABM Addressed binary and safety related message ACA AIS regional channel assignment message ACK Acknowledge alarm AIR AIS interrogation request BB.
%1&'01 6;2' %2 ⇛ޓޓ࿑ 176.+0' ฬޓޓ⒓ 0#/' ᢙ㊂ 36; ↪ㅜ㧛⠨ 4'/#4-5 ⇟ภ 01 ဳฬ㧛ⷙᩰ &'5%4+2 6+105 +056#.
%1&'01 6;2' %2 ⇛ޓޓ࿑ 176.+0' ฬޓޓ⒓ 0#/' ᢙ㊂ 36; ↪ㅜ㧛⠨ 4'/#4-5 ⇟ภ 01 ဳฬ㧛ⷙᩰ &'5%4+2 6+105 +056#.
%1&'01 6;2' (2 ⇛ޓޓ࿑ 176.+0' ฬޓޓ⒓ 0#/' ᢙ㊂ 36; ↪ㅜ㧛⠨ 4'/#4-5 ⇟.
Antenna Cable Set CP20-02700 (004-381-160) CP20-02710 (004-381-170) A-8 %1&' 01 6;2' 52 +6'/ 01 0#/'1( 2#46 176.
Antenna Cable Set CP20-00300 (000-041-938) CP20-00310 (000-041-939) A-9.
Y. Hatai D-1.
Y. Hatai D-2.
Y. Hatai D-3.
Y. Hatai D-4.
Mar,27'07 R.Esumi D-5.
May 20 '03 D-6.
Feb.22'05 D - 7.
Jan. 9, '03 D - 8.
26/Oct/09 R.Esumi D-9.
Feb.02'05 D-10.
Nov.28'03 D-11.
Oct.02'03 D-12.
.
Y. Hatai D-13.
34 12 56 TYPE 名前 NAME kg DWG. No. SCALE APPROVED DRAWN CHECKED MASS C B D A IEC61162-2: 38.4KBPS IEC61162-1: 4800BPS FA-150 U-AIS TRANS PONDER INTERCONN ECTION DIAGRAM 相互結線図 国際船舶自動識別装置 P P P MJ-A10SPF0012,5m,φ8.
デバイスFuruno FA-150の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Furuno FA-150をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFuruno FA-150の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Furuno FA-150の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Furuno FA-150で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Furuno FA-150を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFuruno FA-150の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Furuno FA-150に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFuruno FA-150デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
