GEメーカーFeb-50の使用説明書/サービス説明書
ページ先へ移動 of 16
. ( — —— —— — — — — — — —— —— — —— — —— —-— — —— ——— —— — — —— — —— — — —— — —— — — —— — —- — .
BEFORE YOU BEGIN . . . The GE model 2-9450 is a multiple line business telephone that is designed for easy installation in your home or office. However, it is important that you follow these few simple guidelines.
FEATURES: ■ 32 One-Touch Memory 9 Volume Control Buttons 9 Pulse~one Switch ■ Temporary Tone ■ Intercom ■ Page ■ Call Transfer ■ Fast Redial ■ Mute ■ Do Not Disturb ■ Auto Busy Redial ❑ Hold ■ Conference ■ Speakerphone LOCATION OF CONTROLS: 1.
. 1. Identify Your Existing Wiring System In order for you to properly connect your GE 2-9450 telephones to an ex- isiting wiring system it is imperative that you understand its configura- tion. The following are the most common multiple line situations.
:: ~ -. . . 4 incoming lines with 3 wall jack 4 incoming lines with 4 wall jacks u LINE 1-2 RJ14 JACK LINE 1 RJ1l JACK u m o w m LINE 3 RJ1l JACK a m o * o LINE 2 RJ1l JACK LINE 4 RJ1l JACK LINE 3 LINE 4 RJ1l JACK RJ1l JACK Label the jacks at each location.
, I i 2. Plan Your Installation Afier identifying the system wiring, use the WORK SHEET to the right to plan you installation. Up to 16 GE 2-9450 telephones may be connected to form your office configuration. Each phone will be assigned a Station Number (first column).
., ;. Work Sheet Station ~nes to be Connected bcation Number ;:;=; Tel. 1 Tel. 2 Tel. 3 Tel. 4 # User’s Name # No. 1 ; ; No. 2 / / No. 3 / / No. 4 / / No. 5 / d No. 6 / / No. 7 / / No, 8 / / No, 9 / / No. 10 / / No. 11 / / No. 12 d / No. 13 / / No. 14 / / No.
The GE 2-9450 telephone has been factory assembled for use on a desk or table. A. Remove the clear ACRYL/C COVER that covers / the MEMORY /NDEX. Carefully remove the MEMORY INDEX CARD and the QUICK REFERENCE GUIDE. B. NOTE: THIS STEP IS ESSENTIAL. 1 You must install a 9V Alkaline Battery.
E. Connect a LONG TELEPHONE L/NE CORD to the jack on the back of the telephone Iabelled L/NE 3-4. Connect the other end to wall jack(s) Iabelied 3 & 4 in the same manner described above. F. Connect either end of the CO/LED CORD to the jack on the side of the TELEPHONE BASE UNIT.
! I 4 Install Wall Mounted Telephones (optional) /~~O~~A~Z Telephone line cords must be con- ■ netted (St eps E through L) before AC power con- O .50 nection is made (Step M). Please follow these steps E ‘n 5 ‘7 optional) in their proper sequence.
D. Reverse the HANDSET HOOK by firmly sliding it out of cradle, rotating it 180°, and sliding it back into the cradle. E. Remove the BACK COVER PLATE from the TELE- PHONE BASE UN/T by pushing in the two tabs. F. If the wall jack is Iabelled Line 1-2, connect the short TELEPHONE L/NE CORD to the jack on the telephone Iabelled LINE 1-2.
● O. Plug the AC POWER SUPPLY into the nearest electrical outlet. R After you plug in the AC POWER SUPPLY you should see the /NTERCOM LED flash red and green. Consult the WORKSHEET above to see which Station Number you have assigned to this telephone.
5. System Verification Problem? Check the following for a solution before calling our toll free “HELP” number at 800-448-0329 The following procedure should be used to test system configuration and identify possible system connection errors.
6. Troubleshooting Chart PROBLEM LED’s do not light. j Telephone does not ope~ate during power outages. Telephone functions with the handset, but there is no response to any button with the phone on hook. LED above intercom button is flashing red and green.
. 6. Troubleshooting Chart PROBLEM Telephone does not in- dicate the Line in Use of other types of telephones. No dial tone when handset is picked up. No dial tone when line button is pressed. Will not dial. There is a clicking sound during dialing. You cannot be heard by other party.
. . I FCC REGISTRATION INFORMATION Your GE telephone equipment is registered with the Federal Communications Commission and IS in compliance with parts 15 and 68, FCC Rules and Regulations.
デバイスGE Feb-50の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
GE Feb-50をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE Feb-50の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE Feb-50の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE Feb-50で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE Feb-50を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE Feb-50の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE Feb-50に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE Feb-50デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
