GEメーカーJN327, JV327の使用説明書/サービス説明書
ページ先へ移動 of 12
Use and Car e of Recir culation Hood Model JN327 and V entilating Hood Models JV327, JV337 & JV347 IMPOR T ANT SAFETY INFORMA TION READ ALL INSTRUCTIONS BEFORE USING. W ARNING—TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJUR Y TO PERSONS, OBSER VE THE FOLLOWING: A.
IMPOR T ANT SAFETY INSTRUCTIONS (continued) W ARNING—TO REDUCE THE RISK OF INJUR Y TO PERSONS IN THE EVENT OF A RANGE T OP GREASE FIRE, OBSER VE THE FOLLOWING: * A. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray , then turn off the burner .
T o Operate Lamp Switch Models: JN327, JV327, JV337 Press for OFF and ON. Lamp Switch Model: JV347 Rotate clockwise, first position for NIGHT LIGHT , second position for BRIGHT LIGHT . Fan Switch Models: JN327, JV327, JV337 CENTER position OFF , DOWN position LOW SPEED, TOP position HIGH SPEED.
W ARNING—T O REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR Y TO PERSONS, OBSER VE THE FOLLOWING: A. Installation work and electrical wiring must be done by qualified persons(s) in accordance with all applicable codes and standards, including fire-rated construction.
1. PREP ARA TION OF W ALL CABINET AND W ALL NOTE: For easier installation make all hood and vent cutouts in the cabinet and wall before cabinet is permanently fastened in place. It is recommended that the power supply be brought into the hood from the wall below the cabinet as shown in Fig.
Models JV337, JV347 Model JV347 ducted installation: Use the reusable metal grease filter (WB02X8391). Remove the baffle from the top of the hood. Re-install the baffle so the short side marked “VENTED” is visible. The long side of the baffle should be inside the hood.
3. POWER SUPPL Y A. CIRCUIT VOL T AGE: This hood must be connected to a supply circuit of the proper voltage and frequency as specified on the rating plate. W ire size must conform to the requirements of the National Electrical Code or the prevailing local code for hoods of this rating.
B. ELECTRICAL CONNECTION 1. Be sure the power supply is disconnected before making electrical connections. 2. Remove the connection box cover located on the left side of the fan unit. 3. Attach the power supply through the knockout hole in the back or top of the hood.
Lamp Replacement Model JV347 has a lamp cover . The lamp cover need not be removed for lamp removal or installation. Remove the lamp and replace with an ordinary screw- base lamp bulb NOT MORE THAN 60 W A TTS. T o remove the lamp cover , if desired: • Press the sides with 2 fingers until the side prongs are released.
PROBLEM POSSIBLE CAUSE F AN DOES NOT • A fuse may be blown or a circuit breaker tripped. Replace fuse or reset circuit breaker . OPERA TE WHEN THE SWITCH IS ON F AN F AILS T O • Fan blade striking the hood shell. CIRCULA TE AIR • Excessively soiled filter should be checked and corrected before using the hood again.
Help Us Help Y ou… W rite down the model and serial numbers. Y ou’ll find them on a label on the back wall of the hood. These numbers are also on the Consumer Product Ownership Registration Card that came with your hood.
WHA T IS COVERED FULL ONE-YEAR W ARRANTY For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home to repair or replace any part of the hood that fails because of a manufacturing defect.
デバイスGE JN327, JV327の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE JN327, JV327をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE JN327, JV327の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE JN327, JV327の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE JN327, JV327で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE JN327, JV327を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE JN327, JV327の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE JN327, JV327に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE JN327, JV327デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。