GEメーカーL0523252の使用説明書/サービス説明書
ページ先へ移動 of 12
Installation Instructions Built-In Dishwasher l If you have questions, call 800-GECARES or visit our website at: www.GEAppliances.com I BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT- Observe all governing codes and ordinances.
Installation Preparation PARTS SUPPLIED: [] Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package).
Installation Preparation PREPARE DISHWASHER ENCLOSURE 34" to 35" Underside of Countertop to Floor Max. Square and Plumb Figure A Floor MUST be Even with Plumbing and Electric Senlice Room Floor. Must EnterShaded Area • The rough cabinet opening must be at least 24" deep and 17-5/8" to 18" wide.
Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. Electrical Requirements • This appliance must be supplied with 120V, 60 Hz.
Installation Instructions PREPARE HOT WATER LINE • The line may enter from either side, rear or floor within the shaded area shown in Figure E • The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" dia.
Installation Instructions I STEP 21ADJUST LEVELING LEGS • Move the dishwasher close to the installation location and lay it on its back. / Adjust to Installation Height Figure H • Measure installation height and dishwasher height. Extend leveling legs out from the dishwasher base, 1/4" less than installation height.
Installation Instructions I STEP 61 POSITION WATER LINE AND HOUSE WIRING • Position water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher and components under dishwasher.
Installation Instructions I STEP 91 POSITION DISHWASHER UNDER COUNTERTOP • Check to be surethatwires are secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components. TIP: Check tub insulation blanket, if equipped.
Installation Instructions I STEP 111SECURE DISHWASHER TO CABINET The dishwasher must be secured to the countertop. • Position the dishwasher so that the tub flange aligns with the front face of the cabinet frame.
Installation Instructions I STEP 131 CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES. The drain hose molded end will fit 5/8", 3/4" or 1" diameter connections on the air gap, waste tee or disposer. Cuton the marked line as required for your installation.
Installation Instructions I STEP 141 CONNECT POWER SUPPLY Skip this step if equipped with power cord, Verify that power is turned off at the source. • Remove junction box cover "A". • Locate the three dishwasher wires, (white, black and green) with stripped ends.
Installation Instructions I STEP 161 DISHWASHER WET TEST [] Turn on power supply (or plug power cord into outlet, if equipped). [] Turn dial to Normal "Wash" position. [] Close door. [] Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, checkto be sure that water and power are turned on.
デバイスGE L0523252の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE L0523252をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE L0523252の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE L0523252の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE L0523252で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE L0523252を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE L0523252の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE L0523252に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE L0523252デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。