GEメーカーVentilaの使用説明書/サービス説明書
ページ先へ移動 of 12
Use and Care of Recirculation Hood Models JN322, JN334, JN335, JMW, & JN635 and Ventilating Hood Models JV322, JV324, JV332, JV334, JV335, JV624, JV634, & JV635 — IMPORTANT SAFETY C. When cutting or drilling into wall or ceiling, INSTRUCTIONS do not damage electrical wiring and other hidden utilities.
2 If You Need Service... ● Do not attempt to repair or replace any part of 1 your hood unless it is speciikxdly recommended in this book. All other servicing should be referred to a qualified technician. ● Disconnect hood circuit breaker or fuse before performing any service.
To Operate —Vents (“JN” models only) Lamp switch Fan switch Trim Lamp Switch Models: JN322, JV322 & JV332 Press for OFF and ON. Lamp Stitch All other models. CENTER position OFF, LE~ position NIGHT LIGHT, RIGHT position BRIGHT LIGHT. Fan Switch CENTER position OFF, LEFT position LOW SPEED, RIGHT position HIGH SPEED.
Installation Instructions for General Electric Hood Models: JN322, JN334, JN335, JN634, JN635, JV322, JV324, JV332, JV334, JV335, JV624, JV634, JV635 Important-save for the local electrical inspector% use Power supply connection box on underside of hood.
1. PREPARATION OF WALL CABINET AND WALL FLUSH OR RECESSED BOITOM CABINET NOTE: For easier installation make all hood and vent cutouts in the cabinet and wall before cabinet is permanently fastened in place. It is recommended that the power supply be brought into the hood from the wall below the cabinet as shown in Fig.
2. DUCT INSTALLATION T@e “B” Models: See Figs. 4 and 9. The hood exhaust has been designed to mate with standard 7“ round duct. (A round damper kit may be ordered. Order GE model number JXDA22.)* A. If a rectangular duct is desired, a round-to-rectangular adapter must be used.
3. POWER SUPPLY A. CIRCUIT VOLTAGE: This hood must be connected to a supply circuit of the proper voltage and frequency as specified on the rating plate. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for hoods of this rating.
IMPORTANT: After installation, peel off the transparent protective film stripping from the decorative trim on the front of the hood. (See Fig. 12.) B. ELECTRICAL CONNECTION 1. Be sure the power supply is disconnected before making electrical connections.
Lamp Replacement Remove the lamp and replace with an ordinary screw- base lamp bulb NOT MORE THAN 60 WATTS. Models JN334, JN335, JN634, To remove the lamp cover, if desired: JN635, JV324, JV334, JV335, ● Press the sides with 2 fingers until the side prongs JV624, JV634, JV635 have a are released.
Questions? Use This Problem Solver PROBLEM POSSIBLE CAUSE FAN DOES NOT ● A fuse may be blown or a circuit breaker tripped. Replace fuse or reset circuit breaker. OPERATE WHEN THE SWITCH IS ON FAN FAILS TO . Fan blade striking the hcmd sheI1. CIRCULATE AIR s Excessively soiled filter should be checked and corrected before using the hood again.
Help Us Help You... Write down the model and serial numbers. You’ll find them on a label on the back wall of the hood. These numbers are also on the Consumer Product Ownership Registration Card that came with your hood.
YOUR RANGE HOOD Staple sales slip or cancelled check WARRANTY here. Proof of original purchase date is needed to obtain service I — under warranty. WHAT IS COVERED FULL ONE-YEAR WARRANTY For one yea.
デバイスGE Ventilaの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE Ventilaをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE Ventilaの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE Ventilaの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE Ventilaで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE Ventilaを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE Ventilaの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE Ventilaに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE Ventilaデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。