GEメーカーZBD1870NSSの使用説明書/サービス説明書
ページ先へ移動 of 14
GE Consumer & Industrial Appliances I n s t a l l a t i o n I n s t r u c t i o n s I f yo u ha ve q ue st io ns , ca ll 8 00 . 62 6 .2 00 0 o r vi si t ou r we bs ite a t : ww w .
IMP OR T ANT – The dishwasher MUST be installed to allow for future r emoval fr om the enclosure if service is required. If you received a damaged dishw asher , you should immediately contact your dealer or builder . Optional Accessories – See the Owner ’s Manual for available custom panel kits.
P ARTS SUPPLIED: ■ Two #8 Phillips head wood scr ews, 5/8" long to Two #8 Phillips head wood scr ews, 5/8" long to secure dishwasher to underside of countertop (in literature package).
Installation Preparation PREP ARE DISHW ASHER ENCLOSURE • The rough cabinet opening must be at least 24" deep, 17-5/8" to 18" wide and approximately 34-1/2" high fr om fl oor to underside of the countertop. • The dishwasher must be installed so that drain hose is no more than 10’ in length for pr oper drainage.
Installation Preparation PREP ARE ELECTRICAL WIRING #282 French FOR PERSONAL SAFE TY: Remove house fuse or open cir cuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. #282 French The improper connection of the equipment grounding conductor can r esult in electric shock .
Installation Instructions PREP ARE HOT W A TER LINE • The line may enter from either side, r ear or fl oor within the shaded area shown in Figur e F . • The line may pass through the same hole as the electrical cable and drain hose. Or , cut an additional 1-1/2" dia.
Installation Instructions Figure I • Lay the dishwasher on its back. Remove the four screws securing the toekick to the dishwasher , and remove the toekick . • Remove the single screw just abov e and to the side of each front leveling leg. • Remove the side panels and set the dishwasher upright .
90 ° Elbow Fill Hose Thread Seal T ape Wa ter V a lve Bracket White G r o u nd Black Check That White, Black and Green Dishwasher Wires Are Threaded Thru Hole in Back Remove Junction Box Cover Insert.
Installation Instructions STEP 6 P OSITION W A TER LINE AND HOUSE WIRING • Position water supply line and house wiring on the fl oor of the opening to avoid interference with base of dishwasher and components under dishwasher .
Countertop Figure S Control Panel Counter top Figure T Dishw asher Door 1/2” Min. Installation Instructions STEP 9 P OSITION DISHW ASHER UNDER COUNTER T OP • Push the dishwasher into the cabinet . • Push the sides with your hands. Do not use your knee against the door since door damage will occur .
8 Turn Legs to Adjust Installation Instructions STEP 10 LEVEL DISHW ASHER IMP OR T ANT – Dishwasher must be level for pr oper dish rack operation and wash performance. • Make sure 1/2" minimum gap is maintained (see Figur e T). • Place level on door to check that the dishwasher is level side- to-side.
Installation Instructions STEP 12 CONNECT W A TER SUPPL Y Connect water supply line to 90° elbow . • Slide compression nut , then ferrule over end of water line. • Insert water line into 90° elbow . • Slide ferrule against elbow and secure with compression nut .
11 White G r o u n d Black Check That White, Black and Green Dishwasher Wires Are Threaded Thru Hole in Back Remove Junction Box Cover Insert Power Cord Wires Thru Strain Relief and Tighten Use UL Listed Wire Nuts A C B D Installation Instructions STEP 14 CONNECT POWER SUPPL Y Skip this step if equipped with power cord.
Installation Instructions STEP 16 DISHW ASHER WE T TEST ■ Turn on power supply (or plug power cor d into outlet , Turn on power supply (or plug power cor d into outlet , if equipped). ■ Start the unit to check for leaks. Start the unit to check for leaks.
デバイスGE ZBD1870NSSの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE ZBD1870NSSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE ZBD1870NSSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE ZBD1870NSSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE ZBD1870NSSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE ZBD1870NSSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE ZBD1870NSSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE ZBD1870NSSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE ZBD1870NSSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。