GefenメーカーEXT-COMPAUD-CAT5-444の使用説明書/サービス説明書
ページ先へ移動 of 22
www .gefen.com f 4x4 Component Matrix Over CA T -5 EXT -COMP AUD-CA T5-444 User Manual.
T echnical Support : T elephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 T echnical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday . Write T o: Gefen Inc. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 9131 1 www .gefen.com support@gefen.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 4x4 Component Matrix Over CA T -5 Front Panel Layout 5 4x4 Component Matrix Over CA T -5 Front Panel Descriptions 6 4x4 Component Matrix Over CA .
1 Congratulations on your purchase of the 4x4 Component Matrix Over CA T -5. Y our complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
READ THESE NOTES BEFORE INST ALLING OR OPERA TING THE 4X4 COMPONENT MA TRIX OVER CA T -5 The extender functionality of the 4x4 Component Matrix Over CA T -5 requires • the use of the supplied 1 foot component video and audio jumper cables.
3 Features Switches easily between any four component/audio sources • Sends up to four video inputs to any four remote displays • Maintains 1920 x 1200, 1080p, and 2k resolution video • Extends .
4 12 3 4 5 67 8 9 1 0 1 1 4X4 COMPONENT MA TRIX OVER CA T -5 FRONT P ANEL LA YOUT.
5 Power LED Indicator 1 This LED will become active once the included 24V DC power adapter is properly connected. Output 1 Source LED Indicator 2 The currently selected source being displayed on Monitor Output 1 will be visually acknowledged by an active LED.
6 4 5 6 7 1 2 3 4X4 COMPONENT MA TRIX OVER CA T -5 BACK P ANEL LA YOUT.
7 Component With Audio Extension Input 1 Connect the included jumper cables between the Component With Audio Outputs (Item 5 on this page) and these inputs. Inputs include component video, analog audio, and digital audio connectors. There are 4 inputs that are used in conjunction with the CA T -5 output ports for extension.
8 Front Panel Back Panel T op Panel 5 2 11 3 7 4 1 8 9 10 6 4X4 COMPONENT AUDIO OVER CA T -5 RECEIVER P ANEL LA YOUT.
9 IR Receiver 1 This receiver will receive commands from both the included RMT -4IR remote control and from other commercial IR remote controls. IR commands from commercial IR remote controls are relayed from this unit back to the 4x4 Component Audio Over CA T -5 sending unit where they will be output by the attached IR Blasters.
10 The RMT -16IR remote control will allow the user to select which source each of the 4 connected displays will be viewing at the source location. Each of the 4 displays are assigned a group of 4 buttons that correspond to the 4 source inputs. Please use the information below when selecting the desired source for each display .
11 Each extended location with a 4x4 Component Matrix Over CA T -5 Receiver can use an RMT -4IR remote control to choose which source will be viewed by the attached display . Pressing the numbered buttons will switch to the source connected to the same numbered input on the 4x4 Component Matrix Over CA T -5.
12 How to Connect the 4x4 Component Matrix Over CA T -5 Connect up to 4 component video/audio source devices to the 4x4 1. Component Matrix Over CA T -5 sending unit using the included 5 RCA component video/audio cables. Optionally , connect up to 4 digital coaxial audio source devices to the 4x4 2.
13 The 4x4 Component Matrix Over CA T -5 Receiver can be placed at each remote location. Each receiver can switch between the four sources connected to the 4x4 Component Over CA T -5 Matrix sender . The unit has two methods of switching using either the direct selection buttons or the RMT -4IR remote control.
14 ADJUSTING THE 4X4 COMPONENT MA TRIX OVER CA T -5 RECEIVER Each 4x4 Component Matrix Over CA T -5 Receiver has two trim pots used to adjust the brightness and focus of the video output. These adjustment trim pots are located on the front panel of each unit.
15 RMT -4IR REMOTE IR CODE CONFIGURA TION 4x4 Component Matrix Over CA T -5 receiver Remote Channel 1: Default Remote Channel 4: Remote Remote Channel 1: Default 1 2 Remote Channel 2: 1 2 Remote Chann.
16 Binary T able ASCII Corresponding RMT16-IR Button Binary ASCII Corresponding RMT16-IR Button Binary 1 1 001 1 0001 9 9 001 1 1001 2 2 001 1 0010 a 10 01 10 0001 3 3 001 1 001 1 b 1 1 01 10 0010 4 4.
12345678 Gefen has speci fi cally engineered their products to work with the TIA/EIA-568-B speci fi cation. Please adhere to the table below when fi eld terminating cable for use with Gefen products. Failure to do so may produce unexpected results and reduced performance.
18 Rear of unit Front of unit Rack mount ears are provided for installation of this unit into a 1U rack mount space. Locate the side screws on the unit. 1. Remove the front 2 screws that are located closest to the front of the unit. 2. Using the removed screws, screw the rack mounting bracket into the unit.
19 Video Ampli fi er Bandwidth ....................................................................... 350 MHz Input Video Signal .............................................................................. 1.2 volts p-p Video Resolutions .........
デバイスGefen EXT-COMPAUD-CAT5-444の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Gefen EXT-COMPAUD-CAT5-444をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGefen EXT-COMPAUD-CAT5-444の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Gefen EXT-COMPAUD-CAT5-444の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Gefen EXT-COMPAUD-CAT5-444で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Gefen EXT-COMPAUD-CAT5-444を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGefen EXT-COMPAUD-CAT5-444の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Gefen EXT-COMPAUD-CAT5-444に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGefen EXT-COMPAUD-CAT5-444デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
