GefenメーカーEXT-DVI-1CAT6-GIの使用説明書/サービス説明書
ページ先へ移動 of 28
Audio Embedder 3GSDI EXT-DVI-1CAT6-GI User Manual DVI over 1 CAT6 w/ Galvanic Isolator Release A2 *Pr eferred.
ii 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer ’s instructions.
iii Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notied within two (2) years from the da.
iv T echnical S upport (818) 772-9100 (800) 545-6900 8:00 AM to 5:00 PM Monday - Friday , Pacic T ime Fa x (818) 772-9120 Email support@gefen.com We b http://www .gefen.com Mailing Addr ess Gefen, LLC c/o Customer Service 20600 Nordhoff St. Chatsworth, CA 9131 1 Pr oduct R egistr ation Register your product here: http://www .
v • Always connect a bonding wire between an approved safety ground and the grounding screw on the chassis. • Electromagnetic Interference This product is subject to the following two conditions: .
vi Features and Packing List Features • Compliant with Medical Standards EN60601-1 and EN60601-1-2, 3rd Edition • Extends DVI up to 132 feet (40 meters) over CA T -6a • Extends DVI up to 100 fee.
.
viii Table of Contents 1 Get ting St arted Introduction............................................................................................................ 2 Sender unit .........................................................................
.
.
DVI over 1 CAT6 w/ Galvanic Isolator 1 Ge t ting St ar t ed Introduction............................................................................................................ 2 Sender unit ........................................................
page | 2 Page Title Introduction Sender unit DVI over 1 CAT6 w/ Galvanic Isolator S 5V DC Power DVI In Link EXT -DVI-1CAT6-GIS Gefen DVI over 1 CAT6 w/ Galvanic Isolator S 5V DC Power DVI In Link EXT .
page | 3 Page Title Introduction ID Name Description 1 Link Connect a CA T -5e cable (or better) from this port to the Link port on the Receiver unit. 2 5V DC Connect the included 5V DC power supply to this power receptacle.
page | 4 Page Title Introduction Getting S tart ed Getting S tart ed Receiver unit DVI over 1 CAT6 w/ Galvanic Isolator R 5V DC Power DVI Out EQ Link EXT -DVI-1CAT6-GIR Gefen 1 2 3 4 5 6 7 0 DVI over .
page | 5 Page Title Introduction Getting S tart ed ID Name Description 1 Link Connect a CA T -5e cable (or better) from this port to the Link port on the Sender unit.
page | 6 Connection Instructions 1. Connect the included DVI cable from the imaging source (e.g. camera) to the DVI In port on the Sender unit. 2. Connect a DVI cable from the DVI Out port, on the Receiver unit, to a video scaler or high-resolution imaging display .
.
.
DVI over 1 CAT6 w/ Galvanic Isolator 2 Basic Oper ation DIP Switch Conguration .................................................................................... 10 Default Settings ................................................................
page | 10 DIP Switch Conguration Basic Oper ation Basic Oper ation On the bottom panel of the Sender unit is a bank of 4 DIP switches. Remove the piece of colored tape to reveal the DIP switch bank. These DIP switches provide control over EDID management and color depth.
page | 1 1 EDID Management The DVI over 1 CA T6 w/ Galvanic Isolator can be switched between two EDID modes: Internal or Pass-through. After changing DIP switch 1, the Sender unit must be power-cycled for changes to take effect. DIP Switch 1 Description ON (default) Pass-through mode.
page | 12 The Receiver unit of the DVI over 1 CA T6 w/ Galvanic Isolator has a trim pot that is used to equalize the output signal, compensating for extension distance and cable skew . If there is no output video or if output video contains video artifacts and/or video noise such as snow , use the steps below to adjust the trim pot.
.
.
DVI over 1 CAT6 w/ Galvanic Isolator 3 Appendix Surface Mounting Instructions ............................................................................. 16 Specications ............................................................................
page | 16 The Sender and Receiver units can be mounted on any at surface, as shown below (screws not included). There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the DVI cables.
page | 17 Specications Appendix Connectors & Indicators Video Input (Sender) • 1 x DVI 29-pin, female (digital only) Video Output (Receiver) • 1 x DVI 29-pin, female (digital only) Link (Se.
20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com Stretch it. Switch it. Split it. Gefen’s got it. ® 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.
デバイスGefen EXT-DVI-1CAT6-GIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Gefen EXT-DVI-1CAT6-GIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGefen EXT-DVI-1CAT6-GIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Gefen EXT-DVI-1CAT6-GIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Gefen EXT-DVI-1CAT6-GIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Gefen EXT-DVI-1CAT6-GIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGefen EXT-DVI-1CAT6-GIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Gefen EXT-DVI-1CAT6-GIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGefen EXT-DVI-1CAT6-GIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
