GefenメーカーEXT-HDRS2IR-4K2K-1FOの使用説明書/サービス説明書
ページ先へ移動 of 40
EXT-HDRS2IR-4K2K-1FO User Manual *Pr eferred RELEASE A1 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR.
ii 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer ’s instructions.
iii Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notied within two (2) years from the da.
iv T echnical S upport 8:00 AM to 5:00 PM Monday - Friday , Pacic T ime (818) 772-9100 (800) 545-6900 Fa x (818) 772-9120 Email support@gefen.com We b http://www .
v v Operating Notes • This product operates with SC-terminated single strand multimode ber optic cable. Singlemode ber is not supported. 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR is a trademark of Gefen, LLC. © 2014 Gefen, LLC.
vi Features and Packing List Features • Extends HDMI, RS-232, and Bi-Directional IR over a single ber strand • Extends Ultra HD 4K x 2K (3840 x 2160 @ 30Hz) up to: ► 3300 feet (1000 meters) over 50/125μm OM3e/OM4 ber ► 500 feet (150 meters) over 50/125μm (OM3) ber ► 165 feet (50 meters) over 62.
vii Packing List The 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR ships with the items listed below . If any of these items are not present in the box when you rst open it, immediately contact your dealer or Gefen.
viii Table of Contents 1 Get ting St arted Introduction............................................................................................................ 2 Sender Unit .........................................................................
.
.
1 Ge t ting St ar t ed 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR Introduction............................................................................................................ 2 Sender Unit ..................................
page | 2 Page Title Introduction Sender Unit P 5V DC HDMI In Reset USB IR In/Ext IR Out L Fiber RS-232 EXT-HDRS2IR-4K2K-1FOS w/ RS-232 and 2-way IR Extender over One Fiber S 4K Ultra HD ® P 5V DC HDM.
page | 3 Page Title Introduction ID Name Description 1 RS-232 Connect an RS-232 cable from this port to an RS-232 device. See Using RS-232 (page 17 ) for more information. 2 Fiber Connect an SC-terminated multimode ber optic cable from this connector to the Fiber connector on the Receiver unit.
page | 4 Page Title Introduction Receiver Unit P 5V DC HDMI Out Reset USB IR In/Ext IR Out L Fiber RS-232 EXT-HDRS2IR-4K2K-1FOR w/ RS-232 and 2-way IR Extender over One Fiber R 4K Ultra HD ® P 5V DC .
Page Title page | 5 Introduction ID Name Description 1 RS-232 Connect an RS-232 cable from this port to an RS-232 device. See Using RS-232 (page 17 ) for more information. 2 Fiber Connect an SC-terminated multimode ber optic cable from this connector to the Fiber connector on the Sender unit.
Page Title Connection Instructions ► Video 1. Connect the included HDMI cable between the Ultra Hi-Def source and the HDMI In port on the Sender unit. 2. Connect an Ultra HD display to the HDMI Out port on the Receiver unit using another HDMI cable.
.
.
2 Basic Oper ation 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR Bidirectional IR Control........................................................................................ 10 Controlling the Source from the Viewing Location ........
page | 10 Controlling the Source from the Viewing Location 1. Connect the included IR extender to the IR In/Ext port on the Receiver unit. If using an automation system, connect the 3.5mm mini-stereo connector from the IR In/Ext port on the Receiver unit to the automation system.
page | 1 1 Controlling the Display from the Source Location 1. Connect the included IR extender to the IR In port on the Sender unit. If using an automation system, connect the 3.5mm mini-stereo connector from the IR In port on the Sender unit to the automation system.
page | 12 Controlling the Source / Display from Different Locations Using bidirectional IR, the 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR allows the source and/or display to be controlled from the viewing location or the source location.
page | 13 LED Indicator Status Basic Oper ation The Power (P) and Link (L) LED indicators on the Sender and Receiver unit provides basic information on the current status of the 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR.
page | 14 LED Indicator Status Basic Oper ation Basic Oper ation Sender unit Receiver unit Description • TheReceiverunitisnotpowered. • TheLinkLEDflashesquicklyontheSenderunit. • TheSenderunitisnotpowered.
page | 15 The bottom of the Sender unit has two banks of DIP switches. The bottom of the Receiver unit has a single bank of DIP switches. Each bank is comprised of four DIP switches. Each DIP switch provides control over a dif ferent function. Remove the piece of colored tape to reveal the DIP switch banks.
DIP Switch Conguration page | 16 As of this writing, the only available feature supported by the DIP switches is the baud rate. Other DIP switches are reserved for future use. Baud Rate The baud rate is controlled by DIP switches on the Sender unit.
page | 17 The 4K Ultra HD Extender w/ RS-232 and 2-way IR supports RS-232 pass-through, allowing the control of remote RS-232 devices. The Sender and Receiver unit which are being used to pass-through the RS-232 data must be set to the same baud rate as the RS-232 host and client.
.
3 Appendix 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR Updating the Firmware ........................................................................................ 20 Installing the Device Driver ......................................
page | 20 Updating the Firmware Installing the Device Driver If you are updating the rmware for the rst time, the 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR device driver must be installed. 1. Connect the included 5V DC power supply to the Sender unit.
page | 21 Appendix Updating the Firmware 6. The Computer Management window will open. 7. In the left window pane, under System T ools , click Device Manager . 8. In the right window pane, locate Other devices . The device “4k2k FO Extender Serial Port” will be displayed.
page | 22 1 1. Select Browse my computer for driver software . 12. Click the Browse... button. 13. Select the directory containing the 4K2KFiberOpticExtender.
page | 23 Updating the Firmware 14. The following Windows Security dialog will be displayed: 15. Click Install this driver software anyway to being installing the driver .
page | 24 Updating the Firmware 16. Once the driver has been successfully installed, the following dialog will be displayed: The COM port for the driver will also be indicated. COM12 is shown in the examples below . Y our COM port assignment may vary .
page | 25 Updating the Firmware Appendix Updating the Firmware Before beginning the update procedure, make sure you have the following: ► Windows® PC with installed terminal-emulation program ► Mini USB cable ► 4K Ultra HD Extender over One Fiber w/ RS-232 and 2-way IR Sender and Receiver unit(s) 1.
page | 26 Updating the Firmware 10. Press ‘4’ on the computer keyboard. The following will be displayed: Please send FW le for Sender 2xx MCU Waiting for the le to be sent ... (press ‘a’ to abort) CCCCCCCCCC 1 1. Begin the le transfer using the terminal program.
page | 27 Updating the Firmware 23. Connect the USB cable to the Receiver unit. 24. Press any key on the computer keyboard. The following will be displayed: ------ Receiver Appl Menu (Ver 1.
page | 28 Surface Mounting Instructions The Sender and Receiver units can be mounted on any at surface, as shown below (screws not included). There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the HDMI cables.
page | 29 Specications Supported Formats Video • 4K x 2K (Ultra HD) • 1920 x 1200 (WUXGA) • 1080p Full HD Audio • 7.1 Linear PCM • Dolby® Digital • DTS-HD Master Audio™ Connectors, I.
20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com Stretch it. Switch it. Split it. Gefen’s got it. ® 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.
デバイスGefen EXT-HDRS2IR-4K2K-1FOの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Gefen EXT-HDRS2IR-4K2K-1FOをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGefen EXT-HDRS2IR-4K2K-1FOの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Gefen EXT-HDRS2IR-4K2K-1FOの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Gefen EXT-HDRS2IR-4K2K-1FOで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Gefen EXT-HDRS2IR-4K2K-1FOを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGefen EXT-HDRS2IR-4K2K-1FOの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Gefen EXT-HDRS2IR-4K2K-1FOに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGefen EXT-HDRS2IR-4K2K-1FOデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
