GeminiメーカーGEM-P800の使用説明書/サービス説明書
ページ先へ移動 of 16
Usin g Y our GEM-P800 Security Sy stem ARMED STATUS GEMINI 1 2 3 4 5 6 7 8 Oi219c page 1 Tuesday, September 16, 1997 08:24.
Introduction Congratulations on y our purc hase of an advanc ed GEMINI-P800 Secur ity System. Meticulously developed by a leading manuf actur er of s tate-of- the-art sec urity products, this system will provide you w ith unprecedented peace- of-m ind & inc orpo- rates som e of the m ost sophis ticated f eatures available today.
3 Important - T est Your Sy stem Weekly ! 1 Bell / Battery Test Test y our bell or s iren by pressing followed by . This will cause the bell, or siren to s ound for 2 seconds and also initiate a test of the battery . 2 Zone Test W alk throughout the prem ises , opening each protected door or window, and activating each m otion sensor .
ARMED STAT US GEMINI 1 2 3 4 5 6 7 8 4 Key pad Controls and Indi cator s Status Light will light when all zones are secure and system is ready to be Armed. A C Light will light to indicate that AC Power is present. Trouble Light will light and the Keypad sounder will pulse to indicate that a system tr ou- ble is present.
A rming Your Sy stem When Leaving 1 Before arm in g y our system, m ak e s ure the g reen Statu s li g ht is ON. T his indic ates that all of your protective zones are secure. If any z ones are open, the cor respondin g Zone num ber will be lit. Secure these zones bef ore proceedin g .
Protecting Yourself While at Home 1 Bef ore arm in g y our system, m ak e s ure the g reen Statu s li g ht is ON. T his indic ates that all of your protective zones are secure. If any z ones are open, the cor respondin g zone number will be lit. Secure thos e zones before proc eedin g .
Emergency Buttons The three s ets of em er gency buttons, if progr am m ed, are always active whether the system is ar m ed or disarm ed. Discus s these Buttons with y our installer. The em ergency signal will only be activated when the two respective buttons are pres sed at the sam e tim e.
Disarming Your Sy stem when Returning 1 Enter your premises throu g h the Entry/Exit door. The k eypad w ill sound a steady tone to remind you to disarm the system before your Entry Delay tim e ex pires. 2 Enter your User Code and press . The red Ar m e d li g ht will g o out, indicatin g that the system has been dis arm ed.
Preparing a Fire Escape Plan Even with the most advanc ed fire alar m s ystem, adequate protection r equires an es cape plan. To prepar e your plan, draw floor plans of your building. (space is pr ovided on the next page) Show two exits - a f ront or back door and a window from each room .
10 Fire Protection Floorplan Draw a plan of your premis es below. Oi219c page 10 Tuesday, September 16, 1997 08:24.
Special Functions By pressing A followed by the the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Easy A rm (when system is dis arm ed) The Easy Arm feature allows the s y stem to be arm ed by pressing f ollowed by .
12 The G EM-P800 is constantly monitor ing its own com ponents, as well as all c ritical services , such as AC pow er and the telephone line, to insure that it is alway s ready to provide the protection for which it was des igned. W hen a system trouble does occur , it will caution you by lighting the TROUBLE light and beeping the keypad buzz er.
13 Sy stem Troubles Keypad Beeps or Flashes Zone light ON System Tr ouble Condition Action 2 Beeps 2 Fire Trouble A problem has been detected in the Fire Circuit. Call installing company for serv ice. 2 Beeps 3 W ireless Receiver Trouble A problem has been detected w ith the wireless receiv er.
Your Installer has assigned a User 1 Code which can be used to not only Arm and Dis arm the system, but also to enter the User Program Mode, where y ou can program other user c odes. The following explains how you will use this code to progr am or erase additional user codes .
A mbush Code - In the event that y ou are forc ed by an intruder to disarm your system, this special code c an be used to disarm the system , and simultaneously send a silent alarm to Central Station. If y our s ystem has the Am bu sh f eatu re enabled, the code assigned as the User 8 code will function as y o ur Ambush Code.
NA PCO LIM I TED WA RRA NTY THE FOLL OW ING STATEM ENT IS REQUI RED BY THE F C C . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the m anufacturer's instructions, may cause interference to radio and television reception.
デバイスGemini GEM-P800の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Gemini GEM-P800をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGemini GEM-P800の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Gemini GEM-P800の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Gemini GEM-P800で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Gemini GEM-P800を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGemini GEM-P800の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Gemini GEM-P800に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGemini GEM-P800デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
