GlancetronメーカーGT19wideの使用説明書/サービス説明書
ページ先へ移動 of 23
T ouch Screen LCD Monitors USER’ s GUIDE Rev .A Glancetron GT19-W ide www .glancetron.com.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright.
T able of Contents Usage Notice Precautions............................................................................................................................. 1 Introduction About Glancetron GT -19Wide .......................................
1 Usage Notice ! W arnin g - T o prevent the risk o f fi re or shock hazards, do not expose this product to rain or moisture. ! W arnin g - Please do not open or disassemble the product as this ma y cause e l ec tri c s h oc k.
Introduction About Glancetron GT -19Wide The Glancetron GT -19Wide is a 47cm (18.5”) fl at panel screen with an active matrix, thin- fi lm transistor (TFT) liquid crystal display (LCD). Features include: • Direct analog signal input • Active matrix TFT LCD technology • 1366 x 768 WXGA resolution • 47cm (18.
3 Package Overview LCD Display Power Cord VGA Signal Cable RS-232 Cable USB Cable ( A to B) Quick Start Guide DC Power Supply T ouch Driver CD Screw Audio-in Cable.
Installation Product Overview • Front V iew • Bottom V iew (Without Stand) POWER SWITCH DC IN VGA RS-232 USB 4.
Kensington Security Slot The monitor can be secured to your desk or any other fi xed object with Kensington lock security products. The Kensington lock is not included.
VESA Mount Y our Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which de fi nes a physical mounting interface for fl at panel monitors, and corresponding with the standards of fl at panel monitor mounting devices, such as wall and table arms.
7 Start Y our Installation Please follow these instructions so that you can hookup the cables to associated connector . 1. Lay the LCD fl at on an even surface. 2. Move the stand into position as seen in the step 2 diagram. 3. Remove the cable cover as seen in the step 3 diagram.
Remove the Deskstand Remove 4 screws and then remove hinge. 8.
Connecting the Display (Figure 10.1) T o setup this display , please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC adapter to the power connector on the monitor and the other end into an electrical outlet (10.
(Figure 10.1) 10.
User Controls Front Panel Controls Icon key Name Menu Up Down Enter Power OSD Key Menu off status Menu on status Menu appear Menu disappear / return to main item Brightness Main item select up / Adjus.
12 How to Use the OSD Menus Icon key Name Menu Up Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menus. 2. Choose the adjustment items by pressing the “Enter ” button.
On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically . Left/Right Moving screen image horizontal position to left or right.
Appendix T roubleshooting If you are experiencing trouble with the LCD display , refer to the following. If the problem persists, please contact your local dealer or our service center .
W arning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There may be three sources for this problem. Please check the cable connections or contact your local dealer or our service center for more information.
Product Dimensions 457.80 278.40 312.20 60.00 67.50 214.81 214.17 Front View Side View T op View 16.
Compatibility Modes Mode Resolution H-Frequency (KHz) V -Frequency (Hz) IBM VGA 720X400 31.47 70 IBM VGA 640X480 31.47 60 Apple Mac 640X480 35.00 66 VESA VGA 640X480 37.86 72 VESA VGA 640X480 37.50 75 VESA VGA 800X600 35.16 56 VESA VGA 800X600 37.88 60 VESA VGA 800X600 48.
T ouch Screen Driver Installation The Glancetron GT -19Wide is available with both RS232 and USB connections. The touch driver is located on the enclosed CD-ROM for these operating systems: Windows ® 7, VIST A 64/32 bits, XP , 2000, ME, 98, NT4.0, CE, XP Embedded, Linux, Apple ® Mac OS.
19 Glancetron GT -19Wide Install Instructions: If you are using a PC running Windows ® 7, VIST A, XP , 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the LCD display .
If you are using a PC running Windows ® CE, follow the instructions below: 1. Power on the computer . 2. Make sure that the RS232 or USB cable is connected to the computer . 3. Using Platform Builder , build an image fi le by following the step-by-step instructions found in the folder fi le on the CD-ROM.
デバイスGlancetron GT19wideの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Glancetron GT19wideをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGlancetron GT19wideの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Glancetron GT19wideの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Glancetron GT19wideで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Glancetron GT19wideを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGlancetron GT19wideの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Glancetron GT19wideに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGlancetron GT19wideデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。