Gold's GymメーカーGGBE8057.0の使用説明書/サービス説明書
ページ先へ移動 of 44
Model No. GGBE8057.0 Serial No. Write the serial number in the space above for future reference. QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or if a part is damaged or missing, PLEASE CONT ACT OUR CUST OMER SER VICE DEP ARTMENT DIRECTL Y .
2 W ARNING DECAL PLACEMENT W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 I MPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .
3 W ARNING: T o reduce the risk of serious injury , read all important precautions and i nstructions in this manual and all warnings on the weight bench before using the weight bench. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of the weight bench.
4 Right Side Curl Bar BEFORE YOU BEGIN T hank you for selecting the versatile GOLD’S GYM ® PRO SERIES weight bench. The weight bench of fers an impressive selection of exercise stations designed to develop every major muscle group of the body .
5 M10 x 155mm Screw (131) M8 Nylon Locknut (170) M6 Nylon Locknut (156) M8 Jamnut (177) Bracket Retainer (73) M10 x 100mm Screw (1 17) M10 x 1 10mm Screw (130) M10 x 30mm Screw (134) M10 x 60mm Bolt (.
6 M6 W asher (149) M8 x 40mm Bolt (136) M8 x 65mm Bolt (146) M8 x 90mm Bolt (172) Large W asher (135) M8 W asher (164) M8 x 22mm Shoulder Bolt (143) M10 Lock W asher (86) M10 W asher (148) M6 x 16mm S.
7 Before beginning assembly , carefully read the fol- lowing information and instructions: • T o hire an authorized service technician to assemble the weight bench, call 1-800-445-2480. • Assembly requires two persons. Some steps may require three persons.
8 3. Attach the Front Leg (3) to the Bench Frame (1) with two M10 x 100mm Screws (1 17) and two M 10 W ashers (148). T ighten the Screws used in steps 1 and 3. 4. Attach the Backrest (32) and the Headrest (99) to the Backrest Frame (8) with six M6 x 20mm Screws (122).
9 6. Grease an M10 x 165mm Bolt (123). Attach the B ackrest Supports (7) and two Backrest Bushings (48) to the Bench Frame (1) with the Bolt, two M 10 W ashers (148), and an M10 Nylon Locknut (153). Do not overtighten the Nylon Locknut; the Backrest Supports must pivot easily .
10 10. Slide two Foam Pads (35) onto the Front Leg (3). Then, press two Pad Caps (37) into the Foam Pads. Insert the two Pad T ubes (159) into the Leg Lever (4). Slide two Foam Pads (35) onto each Pad T ube. Then, press a Pad Cap (37) into each Foam Pad.
1 1 13. Orient one of the Front Uprights (1 1) and one of the Base Feet (16) as shown. Attach the Front Upright and the Base Foot to the Base (14) with two M10 x 155mm Screws (131). Then, orient a 38mm x 100mm Large Outer Cap (180) so that the thick end is at the bottom (see the inset drawing), and press it onto the Base Foot.
12 15. Attach a Floor Guard (78) to the the Base (14) with two M4 x 20mm Self-tapping Screws (120). Attach the remaining three Floor Guards (78) to the Base (14) in the same way . 15 78 78 78 14 120 120 120 14. Orient a Rear Upright (12) as shown. Attach the Rear Upright to the Base (14) with two M10 x 1 10mm Screws (130) and two M10 Washers (148).
13 16. Orient the Center Upright (13) as shown and i nsert it into the Base (14). Hold the Foot Plate (15) and the Weight Carriage Base (20) against t he Base. Attach the Foot Plate, Center Upright, and Weight Carriage Base to the Base with two M10 x 1 10mm Screws (130).
14 18 19. Insert the Barbell Guide (1 12) into the indicated hole in the Base (14). Next, lift the Barbell Guide up into the hole in the T op Frame (not shown). Attach the Barbell Guide to the Base with an M10 x 55mm Bolt (127), two M10 W ashers (148), two M10 x 6.
15 20. Attach a Barbell Guide (1 12) to the T op Frame ( 17) with an M10 x 55mm Bolt (127), two M10 W ashers (148), two M10 x 6.5mm Spacers (151), a nd an M10 Nylon Locknut (153). Attach the other Barbell Guide (not shown) to the T op Frame (17) in the same way .
16 23. Attach the W eight Carriage Frame (18) to the W eight Carriage Guides (21) with two M8 x 40mm Bolts (136) and two M8 Nylon Locknuts (170). Do n ot tighten the Nylon Locknuts yet. 23 24. Attach the W eight Carriage Frame (18) to the Center Upright (13) and the T op Frame (17) with two M10 x 25mm Screws (128).
17 26. Grease the bottom of the Right Adjustment B racket (24), and slide the Right Arm (23) onto the Right Adjustment Bracket. See the inset d rawing. O rient two Bracket Retainers (73) so that the teeth bend downward, and press them onto the Right Adjustment Bracket.
18 30. Attach a Barbell Adapter (102) to the Barbell (1 13) with an M10 x 25mm Screw (128) and a Large W asher (135). Then, press a 48mm x 3mm Round Inner Cap (103) into the Barbell Adapter . Attach the other Barbell Adapter (not shown) in the same way .
19 32. T ighten three Weight Storage T ubes (67) onto a R ear Upright (12). A ttach the remaining three Weight Storage T ubes (not shown) onto the other Rear Upright (12) in the same way . 12 12 67 67 67 33. Attach an Upright Pin/T ether (28) to a Weight Rest (26) with an M4 x 16mm Self-tapping Screw (147).
20 34. See the CABLE DIAGRAM on page 34 to iden- tify the cables as you assemble them. Identify the Arm Cable (145). Grease an M8 x 2 2mm Shoulder Bolt (143). Attach the Cable to the Left Adjustment Bracket (25) with the Shoulder Bolt and an M8 Nylon Locknut (170).
21 37. W rap the Arm Cable (145) over a “V”-pulley (75). Attach the “V”-pulley , a Large Cable T rap (77), a nd two Full Pulley Guards (76) to the other side of the bracket on the Center Upright (13) with an M 10 x 60mm Bolt (133) and an M10 Nylon Locknut (153).
22 40. W rap the High Cable (81) around a Small Pulley (74). Attach the Small Pulley to the T op Frame ( 17) with an M10 x 45mm Bolt (140) and an M10 Nylon Locknut (153). 4 0 140 41. Feed the High Cable (81) through the indicated slot in the T op Frame (17).
23 43. W rap the High Cable (81) under a Small Pulley (74). Attach the Cable, a Small Cable T rap (93), a nd two Half Pulley Guards (91) to the second hole from the top of the “U”-bracket (158) with an M 10 x 48mm Bolt (125) and an M10 Nylon Locknut (153).
24 45. Feed the High Cable (81) through the indicated slot in the T op Frame (17). W rap the Cable a round a Small Pulley (74). Attach the Small Pulley to the T op Frame with an M10 x 45mm B olt (140) and an M10 Nylon Locknut (153). 45 46. Feed the High Cable (81) through the T op Frame (17).
25 48. Identify the Rear Cable (94) . Press the Weight Carriage Block (100) into the Weight Carriage (19). Insert one end of the Rear Cable into the the center of the Weight Carriage Block.
26 5 0. W rap the Rear Cable (94) under a Small Pulley ( 74). Attach the Small Pulley , a Small Cable T rap (93), and two Half Pulley Guards (91) at the sec- ond hole from either end of the two Pulley Plates (92) with an M10 x 48mm Bolt (125) and an M10 N ylon Locknut (153).
27 53. W rap the Low Cable (80) over a Small Pulley (74). Attach the Small Pulley and two Half Pulley G uards (91) to the Double “U”-bracket (98) with an M10 x 45mm Bolt (140) and an M10 Nylon L ocknut (153). M ake sure that the Half Pulley Guards are oriented as shown.
28 56. W rap the Low Cable (80) under a Small Pulley (74). Attach the Small Pulley and two Half Pulley G uards (91) to the Weight Carriage Base (20) with an M10 x 45mm Bolt (140) and an M10 N ylon Locknut (153). M ake sure that the Half Pulley Guards are oriented as shown.
29 This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 35 for impor- t ant information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for several exercises.
30 4 132 Weight USING THE LEG LEVER T o use the Leg Lever (4), slide the desired weights (not included) onto the Leg Lever . Secure the weights w ith the Weight Clip (132). Y ou can store unused weights on the weight storage tubes (not shown) on the rear uprights.
31 1 14 11 ADJUSTING THE ARMS T o change the position of the Right Arm (23), pull the Arm Knob (85) out of the Right Adjustment Bracket (24). Then, rotate the Right Arm to the desired posi- tion, and reengage the Arm Knob into the Right Adjustment Bracket.
32 A TT ACHING THE ACCESSORIES TO THE HIGH PULLEY ST A TION T o use the high pulley station, first place the desired weights on the weight carriage (see ADDING WEIGHTS TO THE BARBELL OR THE WEIGHT C ARRIAGE on page 31). Next, attach the Lat Bar (58) to the High Cable (81) with a Cable Clip (63).
33 Make sure that all parts are properly tightened each time the weight bench is used. Replace any worn parts immediately . The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent; do not use solvents to clean the weight bench .
34 CABLE DIAGRAM The diagram below shows the proper routing of the cables. The numbers in each drawing show the proper rout- ing for that cable. Use the diagram to make sure that the cables, cable traps, and pulley guards are assembled correctly .
35 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
36 The repetitions in each set should be performed smoothly and without pausing. The exertion stage of e ach repetition should last about half as long as the return stage. Proper breathing is important. Exhale d uring the exertion stage of each repetition and inhale during the return stroke.
37 MONDA Y Date: / / EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.
38 Key No. Qty . Description Key No. Qty . Description 1 1 Bench Frame 2 1 Rear Leg 3 1 Front Leg 4 1 Leg Lever 5 1 Curl Bar Frame 6 1 Seat Carriage 7 2 Backrest Support 8 1 Backrest Frame 9 1 Seat Fr.
39 Key No. Qty . Description Key No. Qty . Description 101 2 38mm x 100mm Inner Cap 1 02 2 Barbell Adapter 103 2 48mm x 3mm Round Inner Cap 104 2 Barbell Carriage 105 4 Bar Slide Bushing 106 4 Barbell.
40 1 2 3 4 5 35 35 35 35 35 35 36 37 37 168 38 38 39 40 41 41 42 37 37 43 44 45 46 11 7 11 7 11 6 11 8 11 8 11 9 147 147 79 148 148 153 10 34 122 6 9 3 3 49 52 53 54 54 55 55 53 52 56 122 147 147 154 .
41 11 12 13 11 12 14 15 26 27 28 26 27 28 28 29 30 29 30 31 57 5 8 59 59 60 61 62 62 63 6 4 65 66 67 68 67 68 67 68 67 68 67 68 67 68 69 70 71 72 70 71 72 179 165 165 165 75 75 76 76 76 76 77 77 78 78.
42 17 18 19 21 20 22 23 24 25 74 74 7 4 74 74 74 74 74 74 74 74 82 83 84 84 83 82 85 87 88 87 88 85 87 87 82 82 89 90 91 91 91 91 98 92 93 80 91 93 95 95 95 95 87 88 88 95 87 87 97 97 68 68 100 94 94 .
43 1 02 1 03 104 105 1 06 106 105 107 108 109 108 11 0 111 11 2 11 2 11 3 11 4 105 102 103 106 105 107 108 109 11 5 108 111 106 127 148 151 148 151 127 148 151 151 148 166 166 132 153 153 153 104 1 61 161 128 135 128 135 161 161 153 EXPLODED DRA WING D—Model No.
Part No. 255088 R0607A Printed in China © 2007 ICON IP , Inc. T o order replacement parts, please see the front cover of this manual. T o help us assist you, be prepared to pro- vide the following in.
デバイスGold's Gym GGBE8057.0の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Gold's Gym GGBE8057.0をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGold's Gym GGBE8057.0の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Gold's Gym GGBE8057.0の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Gold's Gym GGBE8057.0で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Gold's Gym GGBE8057.0を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGold's Gym GGBE8057.0の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Gold's Gym GGBE8057.0に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGold's Gym GGBE8057.0デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
