Gracoメーカー312781Eの使用説明書/サービス説明書
ページ先へ移動 of 22
312781E EN Instr uctions-P ar ts Fluid Mix Manif old For proportional mixing of plural component coatings. For prof essional use only . See page 2 f or model inf ormation, including maximu m working pressure. Important Safety Instructions Read all warnings and inst r uctions in this manual.
Related Manua ls 2 312781E Contents Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 312781E 3 Installation Air Connections See F IG . 1, F IG . 2, or F IG . 3. 1. Connect 5/32 in. (4 mm) OD air tube s from the valv e solenoids to the air inlets of each valv e . 2. ProMix 2KS and ProMix 3KS systems only: Conn ect an air supply line to air pu rge v alve (APV) inlet (1/4 in.
Installation 4 312781E F IG . 1. ProM ix 2KS and Pr oMix 3KS W all Mount Fluid Stations MA MB DV B MS SPV DV A APV TI12556a SM FI SV A SVB RV B RV A Ke y: Pr oMix 2KS Fluid Station MA Component A Mete.
Installation 312781E 5 F IG . 2. ProM ix 2KE Fluid Controls, Seque ntial Dosing F IG . 3. ProM ix 2KE Fluid Contr ols, Dynamic Dosing ti15699a Key: MA Component A Meter D V A1 Component A Dose V alv e.
Installation 6 312781E Setup the Fluid Manif old f or Dynamic Dosing If you will be operating using dynamic dosing, the fluid manifold must be setup properly f or your application. Order the 15U955 Injection Kit (accessor y) . NO TE: F or ProMix 3KS, order two 15U955 Injection Kits.
Operation 312781E 7 Operation Purging F ollow t he purging procedure in t he propor tioner system manua l. NO TES: • Pu rge before using equipmen t, which was tested with lightweight oil that could contamin ate you r mater ial.
Maintenance 8 312781E Mix Manif old V alve Settings T o open dispense or purge v alve s, turn hex n ut (E) counterclockwise . T o close, turn clockwise . F IG . 4. Maintenance Daily • Purge the mixing system at the end of pr oduction. • Check and refill fluid su pplies for all components and solv ent.
Troubleshooting 312781E 9 T r oub leshooting Isolate a Mixing Pr oblem A mixing prob lem can be caused b y a prob lem with the controller , meters , and solenoid valv es , as well as the mix manif old. 1. T o isolate the problem, check fo r any visible f aults or errors: a.
Repair 10 312781E Repair NO TE: Purge the mix manif old wit h solven t after repair to remov e any e xcess g rease that is u sed f or lubricating par ts. Remo ve the Integrator Mixer See the Pa r t s drawings on page s 14-19. Clean and inspect all par ts.
Repair 312781E 11 Repair the V alves and Seats (Pr oMix 2KS and ProMix 3KS only) V alve Seat Kit 24A86 1 is av ailab le. See page 15. P ar ts included in the ki t are marked with a symbol, f or e xam- ple (16‡). F or best result s, use a ll par ts included in th e kit.
Repair 12 312781E Reb uild the Mix Manifold Manif old Rebuild Kit 15U931 is a vailab le. See page 15. P arts included in the kit are marked with a symbol, for e xample (3 *). F or best results, use all par ts included in the kit. See the Pa r t s drawings on page s 14-19.
Repair 312781E 13.
Parts 14 312781E Pa r t s P art No. 289695, for Pr oMix 2KS Pr oportioner TI11578a 31 41 1 23 15‡* 14* 13* 16‡ 21 11 48 42 43 22 3 49 19 17 18* 5* 12 20 24 25 28 29 30 32 33 35 36 37 38 39* 40* 44 45* 15‡* 15‡* 15‡* 16‡ 17 20 19 31* 39* 18* 31* 46 47 Apply pipe sealant to all pi pe threads when reassembling.
Parts 312781E 15 P art No. 289695, for Pr oMix 2KS Pr oportioner * P arts included in Manifold Rebuild Kit 15 U931 (pur- chase separately). ‡ P ar ts included in V alve Seat Kit 24A861 ( purchase separate ly). (Optional Carbide Se at Kit 15U932 is av ailab le separately .
Parts 16 312781E P art No. 256875, for Pr oMix 3KS Pr oportioner TI14363a Apply pipe sealant to all pi pe threads when reassembling. 1 31 41 1 23 15‡* 14* 13* 16‡ 21 8 48 22 3 49 19 17 18* 5* 12 2.
Parts 312781E 17 P art No. 256875, for Pr oMix 3KS Pr oportioner * P arts included in Manifold Rebuild Kit 15 U931 (pur- chase separately). ‡ P ar ts included in V alve Seat Kit 24A861 ( purchase separate ly). (Optional Carbide Se at Kit 15U932 is av ailab le separately .
Parts 18 312781E P art No. 262398, for Pr oMix 2KE Pr oportioner , Sequential Dosing * P ar ts included in Manif old Reb uild Kit 15U931 (pur- chase separately). Integrator Kits 1 3 5* 21 23 24 25 28 29 30 31* 35 36 37 39* 40* 31* 45 46 47 48 49 ti16301a *31 39* 38 Ref.
Parts 312781E 19 P art No. 262399, for Pr oMix 2KE Pr oportioner , Dynamic Dosing * P arts included in Manifold Rebuild Kit 15 U931 (pur- chase separately). Restrict or Kit ti16327a 1 3 31* 35 40* 55 45 *5 31* 54 36 23 37 39* 38 *39 24 28 29 30 59 57 58 56 25 Ref.
Parts 20 312781E.
Technical Data 312781E 21 Te c h n i c a l D a t a Maximum Fluid Working Pres sure . . . . . . . . . . . . . . . . . . 289 695, 256875, and 262398: 4000 psi (28 MP a, 280 bar) 262399: 4500 psi (31 MP a, 310 bar) Dispense V alv e Fluid Inlet Size . . .
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. Thi s manual contains Eng lish.
デバイスGraco 312781Eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Graco 312781Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco 312781Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco 312781Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco 312781Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco 312781Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco 312781Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco 312781Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco 312781Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。