Gracoメーカー332574Dの使用説明書/サービス説明書
ページ先へ移動 of 28
332574D EN Operation - Repair RS ™ Gun Cutter Assemb lies For use with the RS Guns. For prof essional use only . Impor tant Safety I nstructions Read all warnings and instructions in this manual and t he RS Gun and Cutter , Opera- tion-Repair manual.
2 332574D Contents Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Component I dentificati on . . . . . . . . . . . . . . . . . . . . 4 Cutter , 24E5 12, Extern al Mix Gun, Series C and Prior Cutter , 24P6 81, Inter nal Mix Gun, Serie s A .
Related Manuals 332574D 3 Related Manuals The f ollowing is a list of co mponent man uals written in English. These manua ls and any tr anslated v ersions av ailable can be f ound at www .
Component Identification 4 332574D Component Identification Cutter , 24E512, External Mix Gun, Series C and Prior Cutter , 24P681, Internal Mix Gun, Series A F IG .
Component Identi fication 332574D 5 Cutter , 24E512, External Mix Gun, Series D Cutter , 24P681, Internal Mix Gun, Series B F IG . 2 Key: AA Cutter Head AB Cutter Head Clamp Screw A C Anvil AD Anvil C.
Setup 6 332574D Setup 1. Engage tr igger lock. 2. I nstall cutter : a. If necessar y , use a crescent w rench to adjust piv ot (541) so that it is par allel to gun front en d and the o pen end point s to the fr ont of the gun. See F IG . 3. b . Bac k out scre ws (630).
Operation 332574D 7 Operation Cutter Assembl y RS guns with a cutter installed have two modes of ope r- ation. When the trigger is pu lled halfw a y , mater ial spra ys but the cutter is not activated. When the tr igger is pulle d all the wa y , the air motor in the cutter is star ted and glass begins dispensing.
Operation 8 332574D Adjust Cutter Speed When dispensing a material and glass mixture, the speed at which the cutter spins can be adjusted to ensure the correct r atio of glass to dispense d material. NO TE: It ma y be possible to pre vent pr emature an vil and b lade wear b y slo wing the cutter speed and ad ding an additional st rand of ro ving.
Operation 332574D 9 Adjust An vil to Idler T ension T o adjust th e anvi l (A C) to idler (AJ) tension, the idler position can be adjusted. Se e F IG . 4 on page 7. 1. F ollow Pressure Relie f Procedure fou n d w i t hi n t he RS Gun and Cutter , Operation-Repair man ual.
Maintenance 10 332574D Maintenance T ools Required The f ollowing tools ar e required to perf or m regular main- tenance on the gu n. • 7/16 in. wr ench • 1/2 in. wre nch • 9/16 in. wr ench • 5/8 in. wre nch • 11/16 in. wrench • 3/4 in. wre nch • 13/16 in.
Maintenance 332574D 11 Replace An vil F or par t ref erences, see F IG . 5 on th is page and cutter par ts illustration on page 20. 1. F ollow Pressure Relie f Procedure fou n d w i t hi n t he RS Gun and Cutter , Operation-Repair man ual. 2. Engage tr igger lock.
Maintenance 12 332574D Replace Blades If glass is no t getting cut prop erly , verify the tens ion is correct bef ore replacing the b lades. 1. F ollow Pressure Re lief Procedure f ound within th e RS Gun and Cutter , Operation-Repair manual. 2. Engage tr igger lock.
Maintenance 332574D 13 Replace Chopper Chute Liner 1. F ollow Pressure Re lief Procedure f ound within th e RS Gun and Cutter , Operation-Repair man ual. 2. Engage tr igger lock. 3. Remove the cover . 4. Remo ve the cutter co ver plate . 5. Replace the chute liner .
Troubleshooting 14 332574D T r oubleshooting Prob lem Cause Solution Premature anvil or bl ade wear Excessiv e tension between an vil and cutter head Adjust An vil to Cutter Head T ension , page 8 Cut.
Repair 332574D 15 Repair Air Motor Component Remo v al Ref er to F IG . 10 f or the follo wing steps. 1. Loosen the set screws and pull gently to remov e the cutter head ass emb ly . 2. Remove the f o ur screws that secure the air motor to the plate. 3.
Repair 16 332574D Air Motor Component Installation 1. Lubr icate o-rings an d install the air motor into the muffler housing. 2. Orient the nut bearing cap upside down and insta ll the plunger with o-ring, spring, and w asher . 3. Scre w the air motor assemb ly on the nut bearing cap .
Repair 332574D 17 Air Motor Replacement 1. V er ify o-rin g (603) is installe d between the ba ck plate (601) and the air motor (602). 2. With the air mot or and back plate oriented as shown below , use f our screws (604) to secure them together . NO TICE The air m otor will not function proper ly if the a ir motor is installed incorrectly .
Parts 18 332574D Pa r t s Cutter Assembl y , 24E512-External Mix, 24P681-Internal Mix with Cutter Heads NO TICE T o pre vent undesir ed operation, do not disassem- ble any part of the air motor (602) e xcept f or the air motor muffle r as shown belo w .
Parts 332574D 19 ❄ P ar ts included in an vil slee ve kit 24S001. ★ P ar ts included in idle r assembly kit 24H273. ◆ P ar ts included in cutter co ver kit 24H282. ‡ P ar ts included in cutter co ver kit 24P683. ❖ P ar ts included in cutter hea d kit 24R482.
Parts 20 332574D Cutter Assembl y , 24E512-External Mix, 24P681-Internal Mix with Blade Car tridges NO TE: Series A cutter assemblie s are no longer a vaila ble f or purchase and are shown f or ref erence only and spare par ts orde ring.
Parts 332574D 21 ✿ P ar ts included in cutter hea d kit 24H271. ❄ P ar ts included in anvil slee ve kit 24L037. ★ P ar ts included in idle r assembly kit 24H273. ◆ P ar ts included in cutter co ver kit 24H282. ‡ P ar ts included in cutter co ver kit 24P683.
Parts 22 332574D Air Motor , 24E511 NO TICE T o pre vent undesir ed operation, do not disassem- ble an y part of the air motor that is not a vailab le f or individual sale. See re lated par ts tab le. 1206 1208 1207 1217 1209 1213 1211 1212 1210 1214 1215 1216 1 Apply a light amount of lubricant 118665 to o-r ings.
Parts 332574D 23 ✿ P ar ts included in muffler f elt kit 24H280. ❄ P ar ts included in six pack kit 24E459. Ref P art Description Qty 1206 16C443 NUT , bearing retainin g 1 1207 16C438 PLUNGER, qu.
Accessories 24 332574D Accessories Chopper Air Shutoff, 24F706 External Mix Gel Gun to Chop Gun Con v er sion T o con v er t you r ext er nal mix gel gun to a ch op gun, pur- chase and insta ll the f .
Accessories 332574D 25 Co ver and Chutes Blade Cartridg es P ack of 5 ca r tridges • 4 b lade car tridge - 24E4 48 • 6 b lade car tridge - 24F 602 • 8 b lade car tridge - 24E4 49 Cutter Chute Liner , 16P833 To o l s Hex K eys for Guns, 24F007 Includes: • One 3/32 in.
Accessories 26 332574D Cutter Head Kits Cutter Base Assembl y , 24R480 Clamp Cutter Assembl y , 24R481 Cutter Head Assembl y , 24R482 Cutter Head Assembl y , 24H271 Blades, 24R606 P ack of 100 b lades.
Technical Data 332574D 27 Te c h n i c a l D a t a RS Cutter Assemblies US Metric Air Inlet Working Pressure 24E512 80-125 psi 5.5-8.6 ba r , 0.55-0.86 MP a 24P681 Minimum Air Flow (at 1 00 psi, 7 bar , 0.7 Mp a) 24E512 16.5 s cfm 0.47 m 3 per min. 24P681 Cutter Maxim um Glass Output At 100 psi (7 bar , 0.
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. For patent information, see www.graco.com/patents.
デバイスGraco 332574Dの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Graco 332574Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco 332574Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco 332574Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco 332574Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco 332574Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco 332574Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco 332574Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco 332574Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。