Graco Inc.メーカー3A1450Dの使用説明書/サービス説明書
ページ先へ移動 of 20
II 2 G c IIB T3 Instr uctions - P ar ts List President ® 4-Ball Pumps 3A1450D EN Air -powered pumps f or lo w pressure, high v olume circulation of finishing materials. Do not use for flushing or pur ging lines with caustics, aci ds, abrasive line strippers, and other similar fluids.
Models 2 3A1450D Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warnings 3A1450D 3 Wa r n i n g s The f ollo wing warnings are f or the setup , use , groun ding, maintenance , and repair of this equipment . The e xclama- tion point symbol ale r ts you to a gener al warning and the hazard symbo ls ref er to procedur e-specific risks.
Warnings 4 3A1450D PERSONAL PRO T ECTIVE EQUIPMENT Y ou must wear appr opriate protectiv e equip ment when oper ating, servicing, or when in the opera ting area of the equipment t o help protect y ou from serious injury , including e ye injury , hearing loss, inhalatio n of to xic fumes, and burns.
Installation 3A1450D 5 Installation Gr ounding Pump: use a ground wir e and clamp (Y). See F IG . 1. Loosen the g rounding lug loc knut (W) and wash er . Inser t one end of the gr ound wire into the slot in the lug and tighte n the lock nut secure ly .
Installation 6 3A1450D Plumbing See F IG . 2. Install a fluid shutoff v alve (D) betw een the mix tank (A) and th e pump . When using a stainless steel pump , use stainless steel plumbing to maint ain a corrosion-resistant syst em.
Installation 3A1450D 7 Key: AM i x T a n k B 255143 W all Brack et Accessor y (253692 Pump Stand Accessor y is also av ailable) C Fluid Supply Line; 1-1/2 in.
Operation 8 3A1450D Operation Pressure Relief Pr ocedure 1. Close the b leed-type master a ir v alve (M ). 2. Open the dispensing v alve , if used. 3. Open all fluid dr ain valv es (N) in the system, ha ving a waste container ready to ca tch drain age.
Maintenance 3A1450D 9 Maintenance Preventive Maintenance Schedule The oper ating cond itions of y our par ticular system determine how often maintenance is req uired. Estab lish a prev entive maintenan ce schedule by recording when and what kind of maintena nce is needed, and then determine a regular schedule f or checking you r system.
Maintenance 10 3A1450D Changing the TSL Check the condition of the TSL an d the le vel in the res- er v oir ev er y week, minim um. TSL should be changed at least ev er y month. P ar t No. 206995 Throat Seal Liquid (TSL) carries resi- due from the pump ro d into the reservoir .
Troubleshooting 3A1450D 11 T roub leshooting Prob lem Cause Solution Pump output low on both strokes . Restricted air supp ly lines. Clear any obstructions; be sure all shutoff valv es are open; increase pressure, but do not exceed maximum working pres- sure.
Repair 12 3A1450D Repair Disassembl y 1. Relie ve the pressure , see Pressure Relief Pr oce- dure page 8. 2. Disconnect the hoses fr om the low er and plug the ends to pre vent f luid contamination. 3. See F IG . 4. Remove the 2-piece shield (109 ) by inser ting a screwdriver stra ight into the slot, and using it as a le ver to re lease the tab .
Repair 3A1450D 13 Reassemble the Coupling Adapter and Tie Rods to the Motor NO TE: Use this procedure only if the coupling ad apter (108) and tie rod s (104) ha ve been disa ssemb led from the motor , to ensure proper alignme n t of the mo tor shaft to the piston rod (R) .
Repair 14 3A1450D.
Parts 3A1450D 15 Pa r t s 24H627 3:1 Ratio Pump with 750cc CST Lower 24H628 3:1 Ratio Pump with 750cc SST Lower 24H629 2:1 Ratio Pump with 1000cc SST Lower 24H997 2:1 Ratio Pump with 1000cc CST Lower .
Dimensions 16 3A1450D Dimensions A B C Model Lower Si ze A in. (mm) B in. (mm) C in. (mm) D in. (mm) Appro x. We i gh t lb (kg) 24H627 750 cc 46.3 (117 6) 29. 8 (757) 17.5 (445) 11.5 (292) 73 (33) 24H628 750cc 24H629 1000cc 74 (34) 24H997 1000cc 24J074 750cc 40.
Mounting Hole Layouts 3A1450D 17 Mounting Hole La y o uts TI16666a 17.75 in. (451 mm) F our 7/16 in. (11 mm) diameter holes f or mounting to wall 9.0 in. (229 mm) 11.75 in. (299 mm) 12.375 in. (314 mm) 7.375 in. (187 mm) 16.88 in. (428.8 mm ) 253692 Floor Stand Acce ssory 14.
Performance Charts 18 3A1450D Pe r f o r m a n c e C h a r t s Fluid Outlet Pressure T o find fluid outlet pressure (MP a/bar/psi) at a specific flow (lpm/gpm) and operating pressure (A/B/C): 1. Locate de sired flow at bottom of chart. 2. Follow v er tical line up to inte rsection with selected operat- ing pressure curve (so lid line) .
Technical Data 3A1450D 19 Te c h n i c a l D a t a Air inlet size: 1/2 npt(f) Fluid inlet siz e: 1-1/2 npt(f ) Fluid outlet siz e: 1 npt(f) W etted par ts: See Low er manual 3A0539.
All written and visual data con tained in th is document reflects the late st product information available at the time of pu blica tion. Graco reserves the right to make changes at any time without notice. Original instructions. This manua l contains English.
デバイスGraco Inc. 3A1450Dの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. 3A1450Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. 3A1450Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. 3A1450Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. 3A1450Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. 3A1450Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. 3A1450Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. 3A1450Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. 3A1450Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
