GrizzlyメーカーH3098の使用説明書/サービス説明書
ページ先へ移動 of 28
COPYRIGHT © AUGUST, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #545803624 PRINTED IN JAPAN ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED.
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints.
SECTION 1: SAFETY ........................................................................................................................2 SECTION 2: INTRODUCTION .......................................................................................
-2- H3098 Western Guitar Kit SECTION 1: SAFETY These instructions assume that you are intimately familiar with the safe operation and use of woodworking machinery and woodworking tools, and understand the techniques used to repro- duce this project. If you do not qualify for both of these criteria, STOP building this project for your own safety.
H3098 Western Guitar Kit -3- We are proud to offer the Model H3098 Western Guitar Kit. This kit is part of a growing Grizzly family of fine woodworking products. When assembled according to the guidelines set forth in this manual, you can expect years of enjoyment from this guitar.
-4- H3098 Western Guitar Kit SECTION 3: PARTS INVENTORY Figure 1. Components. 1 4 5 6 7 Figure 2. Hardware. 201 2 202 3 203 204 205 206 207 208 209 210 1 PH3098001 Guitar Body 2 PH3098002 Guitar Neck .
H3098 Western Guitar Kit -5- The majority of the wooden components in this kit are fully machined from the factory and are ready for assembly. A small amount of drilling, sanding and light machining will need to be performed to complete the guitar.
-6- H3098 Western Guitar Kit Like the guitar body, most of the guitar neck has been machined at the factory; however, the neck headstock can be customized to reflect personal taste.
H3098 Western Guitar Kit -7- Attaching the neck to the guitar body is the most crucial part of assembling the guitar. Failure to attach the neck correctly could result in difficult bridge and string adjustments, or even worse, it could lead to unrepairable damage.
-8- H3098 Western Guitar Kit Once the neck/body assembly is completely dry, the truss rod can be installed. To install the truss rod: 1. Test fit the truss rod into the truss rod chan- nel.
H3098 Western Guitar Kit -9- The position mark holes have been predrilled into the side of the fingerboard. To install the position marks: 1. Place a small drop of glue in each position mark hole. 2. Slide the end of the position mark stick into a hole and use a sharp knife to cut it flush with the fingerboard.
-10- H3098 Western Guitar Kit The correct distances between the inside edge of the nut, the center of the 12th fret and the center of the saddle slot are crucial to the performance of this guitar. Figure 8 shows the correct dis- tances. To determine the correct bridge location: 1.
H3098 Western Guitar Kit -11- In preparation for the finish coating, the fol- lowing parts of the guitar (Figures 10 & 11) need to be covered: • Bridge Location • Fingerboard • Sound Hole (Hole Filled With Newspaper) Use a small stick of wood to carefully press all the masking tape edges securely to the guitar pieces.
-12- H3098 Western Guitar Kit Finishing supplies are not supplied with the guitar kit. Note— The guitar body is made from spruce wood and the neck from poplar wood. Clear fin- ishes such as lacquer look exceptionally stunning and glossy on these surfaces.
H3098 Western Guitar Kit -13- Attaching Bridge To attach the bridge to the body: 1. Remove the masking tape from the bridge location. 2. Apply a thin, even layer of wood glue to the back of the bridge. 3. Position the bridge on the bridge location penciled on the body.
-14- H3098 Western Guitar Kit The correct position of the guitar strings is shown in Figure 13 . The thin High E string is called the "1st" string and the thick Low E string is called the "6th" string. To install the guitar strings: 1.
H3098 Western Guitar Kit -15- 6. Route the string to the inside of the corre- sponding tuning peg and through the peg hole. Note— Allow enough string slack to allow 2-3 complete winds around the tuning peg. 7. Turn the tuning button counter-clockwise to tighten the string.
-16- H3098 Western Guitar Kit Correct string height is crucial for maximizing the playability of your new guitar. The string height is the distance between the top face of the fret and the bottom face of the string ( Figure 15 ). Measurements are taken at the following loca- tions.
H3098 Western Guitar Kit -17- To check the string heights of the 1st and 6th strings at the 12th fret: Measure the string heights at the 12th fret ( Figure 17 ).
-18- H3098 Western Guitar Kit Tuning The end pin is positioned on the guitar as shown in Figure 18 . To attach the end pin to the guitar body: 1. Using a 3 ⁄ 32 " drill bit, drill a 3 ⁄ 4 " deep hole at the mounting location . 2. Using a phillips head screwdriver, secure the end pin to the guitar body with the included wood screw.
H3098 Western Guitar Kit -19- To tune the guitar: 1. Play a known Low E pitch. A piano, a tuning fork, or an electronic computer file will work. 2. Play an open (non-fretted) 6th string. The goal is to match the open 6th string to the known Low E pitch.
-20- H3098 Western Guitar Kit This section contains aftermarket accessories and warranty/return information for the Model H3098. If you need parts or help in assembling your machine, or if you need operational information, call the service department at (570) 546-9663.
H3098 Western Guitar Kit -21- NOTES.
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse; abuse; negligence; accidents; repairs or alterations; assembly, finishing or modification of kits; or lack of mainte- nance.
CUT ALONG DOTTED LINE 9. How many of your woodworking machines are Grizzly? _____________ 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8&qu.
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_____________________________.
.
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! -OR- • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR Visit Our Website T oday And .
デバイスGrizzly H3098の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Grizzly H3098をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly H3098の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly H3098の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly H3098で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly H3098を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly H3098の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly H3098に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly H3098デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
