GrizzlyメーカーH6143の使用説明書/サービス説明書
ページ先へ移動 of 20
COPYRIGHT © AUGUST, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN .
H6143 16 Ga. Finish Nailer -1 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck - ties, rings, bracelets, or other jew- elry which may get caught in moving parts.
H6143 16 Ga. Finish Nailer -2 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source .
H6143 16 Ga. Finish Nailer -3 - Operating this nailer can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment.
H6143 16 Ga. Finish Nailer -4 - INTRODUCTION If you have any c omme nts re gard ing th is man ual, pl ease w rite to u s at th e follo wing add ress : Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Mo st i mpor t antl y , we st and b ehi nd o ur too ls.
H6143 16 Ga. Finish Nailer -5 - SET UP Figure 1. Model H6143 inventory. Unpacki ng Y our Mo del H 6 143 l eft ou r ware hous e in a c arefu lly pac ked b ox. If you di scover th e nai ler is dam age d af ter you have sig ned fo r del iver y , pl ease i mme diat ely cal l Cus tomer Ser vice at ( 5 70 ) 546 -9 66 3 for advic e.
H6143 16 Ga. Finish Nailer -6 - Compressed Air Sy stem The M ode l H 61 4 3 is des igne d to b e o per- ated at 60 –1 0 0 PSI using c lean, dr y , reg u- late d, c ompr ess ed a ir . DO NO T exce ed th e 120 P SI m axi mum op er atin g pre s- sur e fo r you r m ode l.
H6143 16 Ga. Finish Nailer -7 - Safety Nose Mechanism A s afety me cha nis m on the no se o f the nai ler p rotec ts ag ain st ac ci dent al f irin g. Whe n the tri gge r is pres sed, t he nail er will not fire un til th e safet y nos e me cha nism is dep ress ed.
H6143 16 Ga. Finish Nailer -8 - OPERATIONS Loadin g Figure 3. Sliding magazine pusher back and engaging catch lever. When replacing nails in your Model H6143, follow these guidelines: Gauge: 16 Length: 1 1 ⁄ 4 " – 2 1 ⁄ 2 " Capacity: 74 To load your nailer: 1.
H6143 16 Ga. Finish Nailer -9 - Figure 6. Depth adjustment controls. A depth adjustment knob is attached to the nose for setting the nail depth. To adjust the dep th: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Rotate the adjustment knob ( Figure 6 ) clockwise to drive the nails deeper or counterclockwise to drive the nails shallower.
H6143 16 Ga. Finish Nailer -10 - A jammed nail m ust be cleared before using the nailer again. To clear a jammed nail from the dis- charge area: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Pull back and latch the magazine pusher. 3. Remove the nail stick from the maga- zine.
H6143 16 Ga. Finish Nailer -11 - Replacin g Pist ons / O - Rin gs If yo u use your nail er day i n an d day out , re pair pist ons are cheap ins uran ce agai nst wa sted d own tim e and lo st prof its, in t he event t hat a p isto n or p isto n shaf t bec ome s wo rn out.
H6143 16 Ga. Finish Nailer -12 - CLEANING & LUBRICATION Cleanin g Use a go od so lvent to c lean t he n ose ass emb ly of the nai ler . Al ways be sure tha t th e n ailer is dr y before us ing it a gain. Do n ot all ow du st, c hip s, san d, etc .
H6143 16 Ga. Finish Nailer -13 - H6143 PARTS BREAKDOWN .
H6143 16 Ga. Finish Nailer -14 - H6143 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6143001 SPECIAL CAP SCREW 48 PH6143048 PIN 2 PH6143002 AIR DEFLECTOR 49 PEC09M E-CLIP 6MM 3 PH6143003 BUMPER WASHER 50 PH6143050 DIRECTION PIN 4 PSB38M CAP SCREW M5-.
H6143 16 Ga. Finish Nailer -15 - TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trig- ger valve area. 1. O-rings in trigger valve hous- ing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking between housing and hose.
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name _________________________________________________________________ Street _________________________________________________________________ City _______________________ State _______.
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street______________________________.
デバイスGrizzly H6143の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Grizzly H6143をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly H6143の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly H6143の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly H6143で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly H6143を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly H6143の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly H6143に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly H6143デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。