GrizzlyメーカーH6145の使用説明書/サービス説明書
ページ先へ移動 of 20
COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages.
H6145 28° Clipped Head Framing Nailer -1 - 6. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PER- SONNEL TO OPERATE MACHIN- ERY. Make sure operation instruc- tions are safe and clearly under- stood. 7. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visi- tors a safe distance from the work area.
H6145 28° Clipped Head Framing Nailer -2 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source .
H6145 28° Clipped Head Framing Nailer -3 - Operating this nailer can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment.
H6145 28° Clipped Head Framing Nailer -4 - INTRODUCTION If you have any c omme nts reg ard ing th is man ual, pl ease w rite to u s at the follow ing add ress : Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Mo st i mpor t antl y , we s tand b ehin d ou r too ls.
H6145 28° Clipped Head Framing Nailer -5 - SET UP Figure 1. Model H6145 inventory. B C D G Unpacki ng Y our Mo del H 61 4 5 lef t our ware hou se i n a c arefu lly pac ked b ox.
H6145 28° Clipped Head Framing Nailer -6 - Compressed Air Sy stem The M ode l H 61 4 5 is des igne d t o b e o per- ated at 70-1 20 PS I us ing cle an, dr y , r egu - late d, c omp ress ed a ir . DO NOT exce ed th e max imum op er ati ng pre ssu re for your mod el .
H6145 28° Clipped Head Framing Nailer -7 - Safety Y ok e A safet y yoke me chan ism (b ump fi re) o n the nos e of the nai ler ac ts as a se con d- ar y safet y d evic e. W hen th e t rig ger i s pres sed , the nailer wil l not f ire un til t he safet y yoke m ech anis m i s de pres sed.
H6145 28° Clipped Head Framing Nailer -8 - OPERATIONS Loadin g Figure 3. Sliding pusher toward the catch lever pusher. When replacing nails in your Model H6145, follow these guidelines: Diameter: 7 .
H6145 28° Clipped Head Framing Nailer -9 - Figure 6. Loosening cap screw for depth adjustment. The nose of the gun houses a depth adjust- ment mechanism for setting the nail depth.
H6145 28° Clipped Head Framing Nailer -10 - A jammed nail must be cleared before using the nailer again. The two places where a nail ca n get jammed are the maga- zine and the discharge area. To clear a jammed nail from the maga- zine: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2 .
H6145 28° Clipped Head Framing Nailer -11 - Replacin g Pist ons / O - Rin gs If yo u us e your na iler day i n an d day out , repa ir pisto ns are chea p ins uran ce agai nst wa sted do wn tim e and los t profi ts, in the event that a p isto n or pi ston sha ft bec ome s wo rn o ut.
H6145 28° Clipped Head Framing Nailer -12 - CLEANING & LUBRICATION Cleanin g Use a go od s olven t to cl ean t he no se ass emb ly of the nail er . Always be s ure th at t he n ail er i s dr y bef ore us ing it agai n. Do not a llow du st, c hips , s and, etc .
H6145 28° Clipped Head Framing Nailer -13 - H6145 PARTS BREAKDOWN .
H6145 28° Clipped Head Framing Nailer -14 - H6145 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6145001 SPCL CAP SCR M8-1.25 X 30 48 PW02M FLAT WASHER 5MM 2 PH6145002 AIR DEFLECTOR 49 .
H6145 28° Clipped Head Framing Nailer -15 - 1. O-rings must be replaced & operation of safety yoke must be checked. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting & use teflon tape 1. Replace damaged seals. 1. Tighten screws and fit - tings.
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Name _________________________________________________________________________ Street ________________________________________________________________________ City____________________State________Zip_.
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street______________________________.
デバイスGrizzly H6145の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Grizzly H6145をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly H6145の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly H6145の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly H6145で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly H6145を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly H6145の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly H6145に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly H6145デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。