HaierメーカーHBF1055TVEの使用説明書/サービス説明書
ページ先へ移動 of 18
Automatic Drum W ashing Machine HBF1055TVE HBF855TVE T able of Contents Before using Names of Parts---------------------------------inside front cover Matters Needing Attention------------------------.
Names of Parts T able Cover Program Knob Operation Button Drainage hose clip Back plate Packing bolt (3) W ashing Allocating box W ash Door Observing Glass Window Drainage hose Earth terminal Power su.
Safety 1. A separate earthed socket is required for the power supply . After installation of the washing machine,the power plug should be accessible during the normal wash. 3. Fuses in the power circuit should be rated for 15A. Refer to a washing machine techni- cian or a Haier designated service point for power cable replacement.
Matters Needing Attention 2 Use ƽ.
9. Keep the door slightly open when the washing machine is not being used. Never cover the machine with a plastic sheet. 4. Do not wash foam rubber or similar sponge materials. 5. Before washing, do up zippers, buttons , laces and repair damaged areas,under- wear or small articals should be placed in the laundry bag or a pillowslip.
As shown in figure1 remove all the packing materials (including the foam base). Fig 1 Remove the packing screws as shown in figure 2. The packing bolts protect the appliance from shock during trans- portation The steps below should be followed before using the appliance, 1.
Connection of water inlet hose and washing machine W a t e rd r a i n a g eh o s e Connection of power supply The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine.
6 C o n t r o l P a n e l T urn the knob at "0", then turn of f the power and turn the program knob for setting desired wash program. The program knob will not rotate with the programmed washing process.
7 Operational Functions Extra Rinse Button Soak Button Pause/Start Button Press this button,the washing machine will not drain before the final spin-drying cycle.a soaking cycle will be started,and the inner drum will rotate once every 4 minutes(at both directions).
Program Selection 8 Heavy Prewash Normal Light Delicate Normal Light Delicate Normal Delicate Normal Delicate Silk 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 V ery heavy soil Non-fade heavily soiled woolen.
1. Power supply Plug in the power supply 120V~/60Hz. 3. Laundry treament 2. W ater supply T urn on the tap ensure that the water is clear . Caution: Before staring the washing machine turn on the water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak.
1. Laundry loading Evenly load the laundry in the washing machine and then tightly close the door of the washing machine Note: 1) When first using the washing machine, let it run un- loaded for one program to pre- vent the laundry from being tainted by oil or dirty water from the washing machine.
11 6. End W ait 2-3 minutes after the washing process is finished , press the power button again to cut off the power supply . Open the door to take out the laundry .
Other Functions 1. Power-off memory funtion: This machine has a power-off menmory funtion. In case of abrupt power failure or the power must be cut off during a program cycle, the present settings will be saved, and operation will resume when the power is switched on again.
Insert the bolts. 5. If the machine is to be moved a distance location, replace the vibration mounting locks which were re- moved during installation as shown below. 1. T urn of the water and electricity supply af- ter every wash. Open the door to prevent the formation of moisture and odors.
The following circumstances do not constitute problems. Do not contact the maintenance service until the problem has been confirmed. Problem Possible Cause The washing machine fails to operate Poor co.
Model Maximum working current (A) W ater pressure (MPa) W ashing power (W) Spinning power (W) Spinning speed (r/min) Size (HXDXW) (mm) W eight (kg) HBF1055TVE 120V~/60Hz 13 0.
W iring Circuit 16 Motor M1 M2 M3 M5 M7 M8 CN2-1 CON8 CON6 CN3-3 CN2-3 CN2-5 CN2-7 CN2-9 CN2-11 CON3 CN3-5 CN3-7 CON2 CON1 PCB N G L FA MRN MRL MRC MR EVF EVP PS EVC 12 13 14 11 P PCB-Printed Circuit .
デバイスHaier HBF1055TVEの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Haier HBF1055TVEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHaier HBF1055TVEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Haier HBF1055TVEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Haier HBF1055TVEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Haier HBF1055TVEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHaier HBF1055TVEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Haier HBF1055TVEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHaier HBF1055TVEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。