American DynamicsメーカーAD1684Bの使用説明書/サービス説明書
ページ先へ移動 of 28
Model AD1684B Receiver Dual Channel General Purpose Receiver Installation Instructions This manual describes the installation and operating procedures for the AD1684B Dual Channel Receiver. The Receiver provides for the control of a Pan/Tilt drive and a motorized Lens for two separate cameras.
This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the purchaser under a license for use on a single system.
The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301D ! W W W W A A A A R R R R N N N N II I I N N N N G G G G To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.
.
CONTENTS Page DESCRIPTION............................................................................... 1 FEA TURES ..................................................................................... 1 Pan/T ilt and Lens Control ...................
.
AD1684B DESCRIPTION DESCRIPTION The AD1684B Receiver is used with American Dynamics Matrix Switching Systems to control pan, tilt, zoom, focus, iris, and auxiliary functions at a camera site. This Receiver is classified as a dual channel type, since two independent control channels are supplied.
SETUP AD1684B SETUP Receiver Configuration Setup AD1684B Receivers may be configured as a two-channel Pan/Tilt and Lens control unit or a single channel unit with four auxiliaries. A two-position Berg jumper, labeled J5 (see Figure 1), is provided to establish this configuration.
Camera Number Setting There are two DIP switches which associate the camera number with the respective channel, A or B. DIP switch S1 is for Pan/Tilt and lens control of Channel A, and DIP switch S2 is for Pan/Tilt and lens or auxiliary control of Channel B.
SETUP AD1684B 4 Table 4 - S2 Pan/Tilt and Lens Camera Number Switch Settings or Auxiliary Settings Channel B L = left ("off"); R = right ("on") CAMERA SWITCH CAMERA SWITCH NUMBER 1.
AD1684B INSTALLATION INSTALLATION This installation should be made by qualified service personnel and should conform to all local codes. Safeguards must be taken to avoid unintentional operation by employees and maintenance personnel working about the premises, by falling objects, by customers, by building vibration, and by similar causes.
CONNECTIONS AD1684B CONNECTIONS Code Line Connections The Code Line connection to the Receiver is made with user- supplied, shielded 2-wire twisted pair, Belden 8760 or equivalent (for Plenum use Belden 88760 or equivalent). The maximum code line length is 5000 feet.
AD1684B CONNECTIONS Pan/Tilt and Lens Connections The Receiver connection to a Pan/Tilt and a motorized Lens is with a 10-pin connector. This connector is located on the left side of the PCB and is labeled J7 (see Figure 1, page 2).
CONNECTIONS AD1684B Table 5 - Dual Pan/Tilt and Lens 10-pin Connector Pinout Channel A - J7 PIN No. FUNCTION Pan/Tilt PINOUT LENS PINOUT 01 Focus __________________ __________________ 02 Zoom ________.
AD1684B CONNECTIONS Auxiliary Connections The Receiver connection of auxiliary equipment is with a ten (10) pin connector, labeled J6, located on the right side of the PCB (see Figure 1, page 2).
CONNECTIONS AD1684B Pre-position (Preset) Connections The Receiver connection to a Pan/Tilt or Lens unit with pre- position servos is with a ten (10) pin connector labeled J4 (see Figure 1, page 2). For dual-channel operation a second 10-pin connector labeled J3 is used for channel B.
AD1684B CONNECTIONS Table 7 - Pre-position Pan/Tilt and Lens 10-pin Connector Pinout Channel A - J4 PIN No. FUNCTION Pan/Tilt Servo PINOUT Lens Servo PINOUT 01 + REF __________________ _______________.
CONNECTIONS AD1684B Power Input Connections Refer to the instructions provided with the enclosure for suitable conduit connectors (when required), and mounting and caution information. Two PG-16 liquid-tight bushings are supplied for use with cord diameters from .
TYPICAL SYSTEM CONNECTIONS.
.
TYPICAL SYSTEM CONNECTIONS AD2150 Controller to AD1684B MAXIMUM DISTANCE between AD1684B and AD2150 is 5000 Ft, using shielded, 18 AWG cable AD2150 AD1684B BWS RS232 PORTS 123 KEYBOARDS 2345 CAMERAS A.
TYPICAL SYSTEM CONNECTIONS AD1996 Controller to AD2091 Code Generator, to AD1684B AD1684B AD2091 AD1996 ABCDEF ON OFF ABCDEF ON OFF ABCDEF ON OFF ABCDEF ON OFF B W S B W S B W S B W S B W S B W S B W .
TYPICAL SYSTEM CONNECTIONS AD1684B to AD1240P Pan/Tilt with Pre-position AD1684B 13-Pin Connector 1240P PAN/TILT 123456789 1 0 1 1 1 2 1 3 BLACK WHITE SHIELD FOCUS ZOOM IRIS DC GROUND AC COMMON DOWN UP DC GROUND RIGHT LEFT + REF PAN TILT FOCUS ZOOM - REF SHIELD SHIELD N.
.
INDEX.
.
Auxiliaries Configuration Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
An American Dynamics Product Designed and built by Sensormatic CCTV Systems Division One Blue Hill Plaza Pearl River, New York, 10965 Business: (914) 624-7600 Technical Support Center: 1-800-442-2225 .
デバイスAmerican Dynamics AD1684Bの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
American Dynamics AD1684Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAmerican Dynamics AD1684Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。American Dynamics AD1684Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。American Dynamics AD1684Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
American Dynamics AD1684Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAmerican Dynamics AD1684Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、American Dynamics AD1684Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAmerican Dynamics AD1684Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。