HaierメーカーHW70-1201B-Uの使用説明書/サービス説明書
ページ先へ移動 of 20
AutomA tic Drum W Ashing mAchine USER MANUAL hW 80 - 1 4 01 B -u hW 70 - 1 4 01 B -u hW 70 - 1401 s -u h W 70-1 4 01 -u hW 70 - 1201 B- u hW 70 - 1201 s -u hW 70 - 1201 - u hW6 0-1 4 0 1 B-u hW6 0-1 4.
t ABle of contents IMPORTANT DISPOSAL INSTRUCTIONS As a responsible retailer we care about the environment. As such we urge you to follow the correct disposal procedure for your product and packaging materials. This will help conserve natural recourses and ensure that it is recycled in a manner that protects health and the environment.
03 Before use 1 x I nlet ho se as sem bly 1 x D rai n hose b rac ket 1 x U ser m anua l 4x Blan kin g plug s Delay components THANKS FOR PURCHASING A HAIER PRODUCT Please read these instructions carefully before using this appliance.
04 Before use T1 T2 T3 S1 S2 S4 S3 T4 Control panel Door handle Work top Washer door Start/Pause Detergent distribution drawer Filter cover PREP ARING THE MACHINE Remove all the packing materials to prevent unsteadiness, including the polystyrene base.
05 Before use sAfety instructions DO ... ... Make sure that the transport bolt are removed. ... Use a separate earthed socket for the power supply . ... Make sure that the plug is accessible. ... Hold the plug and not the electric cable when unplugging the power supply .
06 Before use 3. 1 . 2. 4. DISMANTLE THE TRANSPOR T A TION BOL TS The transportation bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process. Remove the back cover . 1. Remove the four bolts on the rear side and take out the synthetic 2.
07 Before use 1 . 2. 1 . 8 0 - 1 0 0cm 2. INLET HOSE 1. Connect the nut on the inlet hose to the connector on the water valve. 2. Apply inlet hose to a water tap with cold, fresh water . Note: Use the hose-set supplied with the appliance. Old hose-sets should not be reused.
08 Before use A B C D E F G H K L J OPERA TIONAL FUNCTIONS control p Anel A Pro gra m kno b B Power Sw itc h C St ar t/Paus e but t on D Spi nnin g Spee d Set t ing b ut to n E Washi ng tem per at ure.
09 Before use F ¬Delay Button T ouch this button lightly , the washing machine will star t operation after a period of time and the corresponding indicator will go on.
2 1 3 1 Detergent compartment for prewash mode 2 Detergent compartment 3 Compartment for softener and other additives 10 using the APPLiAnCe progrAm selection PROGRAM MODES Preset spin speed Program M.
11 using the APPLiAnCe consumption AnD technicAl DA t A TECHNICAL DA T A CONSUMPTION T ABLE The wash cycle times are intended as a guide only . The actual time used may vary due to different water pressure, initial water temperature, etc.W ARNING: Never overload the washing machine.
12 using the APPLiAnCe W Ashing methoDs POWER SUPPL Y Connect the washing machine to the power supply (220V to 240V~/50Hz). W A TER CONNECTION T urn on the tap. The water must be clean and clear . Note: Before use, check for leakage in the joints between the tap and the inlet hose by turning on the tap.
13 using the APPLiAnCe LOADING THE MACHINE Open the washer door , put in the laundr y piece by piece. Close the door tightly . ¬ When first using the washing machine, let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine.
14 using the APPLiAnCe SETTING W ASHING TEMPERA TURE Press and hold down the temperature button until the desired temperature is selected . SETTING SPIN SPEED Press and hold down the speed button until the desired speed is selected.
15 using the APPLiAnCe Bed sheet (single) Cotton Approximately 800g Blanket Wool Approximately 3000g Blended fabric clothes / Approximately 800g Jackets Cotton Approximately 800g Jeans / Approximately.
16 1. 2. 1 . 2. maintenance cleAning & cAre AFTER W ASHING T urn off the water supply and pull out electricity plug after each wash. Open the washer door to prevent formation of moisture and odours. If the washing machine is left idle for a long period, drain the water in the machine and replace the drain hose.
17 maintenance W A TER INLET V AL VE AND INLET V AL VE FIL TER T o prevent blockage to the water supply by ingress of foreign substances, clean the water inlet valve and inlet valve filter regularly .
18 maintenance DisplA y coDes DISPLA Y CODES AND SPECIAL FUNCTIONS ¬ Control panel lock function: Press the "Delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a program. It can no longer be changed by operating buttons or knobs.
19 maintenance trouBleshooting TROUBLESHOOTING The following circumstances do not constitute problems. Do not contact the Service Center until the problem has been confirmed. PROBLEM CAUSES SOLUTIONS Washing machine fails to operate. ¬ Poor connection to the power supply .
Impor t a nt S afe t y In f or m a t Ion 20 Do not use a multiple socket extension cord. A separate earthed socket is required which shall be accessible at all times.
デバイスHaier HW70-1201B-Uの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Haier HW70-1201B-Uをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHaier HW70-1201B-Uの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Haier HW70-1201B-Uの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Haier HW70-1201B-Uで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Haier HW70-1201B-Uを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHaier HW70-1201B-Uの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Haier HW70-1201B-Uに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHaier HW70-1201B-Uデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
